Faster faster please DoL.190.0067480380 Wire BC, has a diameter of D, and made of A-36 steel, is used to support member AB at B asshown. Determine the value of the force P (kN) that causes a decrease of D in the diameter ofwire BC. The values of the original diameter (D.) of wire BC, D, L,, and L; are given in tablebelow.L1В400 mm-

Answered: Image /qna-images/answer/39c55f3d-acae-4c77-850b-17f36c5dabe2.jpg

Answered: Determine the value of the force P (kN)

Engineering

Civil Engineering

Determine the value of the force P (kN)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q.1//The bar AD is considered to be absolutely rigid and is horizontal before the load of 200 KN is applied. The connection at A is a pin, and AB is supported on the steel rod BE and the copper rod CF. The length of BE & CF is 250 mm. The cross sectional area of CF is 400 mm, the area of BE is 200 mm. тт. Determine the stress in each of the vertical rods. The weights of all bars are negligible. For copper E=120 GPa, for steel E=200 GPa. 200 KN A• D 1.5 m 500 mm 1500 mm 250 mm steel copper
8) If the elongation of wire BC is 0.2 mm after the force P is applied, determine the magnitude of force P. The wire BC is A36 steel and has a diameter of 3 mm. 200 G Pa E A36 400 mm 300 mm B 200 mm-
The assembly consists of three titanium (Ti-6A1-4V) rods and a rigid bar AC. The cross-sectional area of each rod is given in the figure. If a force of 60 kip is applied to ring F and the allowable stress of the material is 67 ksi, determine the cross-sectional area of each rod and the horizontal displacement of point F. B AAB = a in² E 6 ft -1 ft2 ft- AEF 2a in² 2 ft FO 60 kip D ACD= 1.5a in² C
H.W. steel : Find forces and elongations wires, in each wire. A=80mm L=4m E=200 G Pa Estrelaxation. ск k 200mm Rigid 5k by F 100 100 1KN
Consider the structure shown in (Figure 1). Assume the cornections A, B, and C are pins. Suppose that P=5k, and P₂ = 4 k. w=300 lb/ft Figure 12ft Part C Cz. Cy= 1 of 1 Submit 15. ΑΣΦΑ Part A Request Answer Determine thee and y components of force at the connection A. Express your answers using three significant figures separated by a comma. VAX it vec Az. A₂= Submit B₂.B,- Determine the x and y components of force at the connection C. Express your answers using three significant figures separated by a comma. Submit Request Answer Part B Determine the z and y components of force acting on the member AB at the connection B. Express your answers using three significant figures separated by a comma. AEoit vec Ivec Request Answer ? ? k k ? k
Problem # 4. A 12-mm-diameter steel E 200 GPa] rod (2) is connected to a 30mm wide by 8 mm thick rectangular aluminum [E 70 GPa] bar (1), as shown. required to Determine the force P stretch the assembly 10.0 mm. Ans: = A (1) 0.45 m B (2) 1.30 m - C
Determine the maximum tensile and compressive bending stresses developed in the beam shown. The cross-section has the given properties. NA 1-35 x 10mm a. RA = b. RE= c. fb(c) = d. fb(T) = 80 mm 200 mm A 1.5m kN KN 5kN m MPa MPa B 1.5m SkN/m 2m 5KN n 2m 4
!! Show Comlete & Detailed Solution w/ FBD !!The rigid bars AB and CD are supported by pins at A and D. The vertical rods are made of aluminum and bronze. When the force P = 18 kips is applied, and neglecting the weights of the members, determine the:a. axial force of the aluminum bar;b. axial force of the bronze bar;c. deformation of the aluminum bar;d. deformation of the bronze bar;e. vertical displacement of the point where Pis located.
b. Discuss how the figure below and determine the rigid bar BDE as used to support by two link AB and CD. 0.4 m 0.3 m B D 0.4 m 30 kN E 0.2 m The Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 500 mm2. Link CD is made of steel (E = 200 GPa) and has a cross- sectional area of (600 mm2). For the 30-kN force shown, determine the deflection a) of B, b) of D, and c) of E.
Two aluminum (Ea=77 GPa) rods AB and CD, and a steel (Es=202 GPa) rod EF support a 82.7 kN load P. Each of the rods has a 400 mm2 cross- sectional area. Neglecting the deformation of rod BED, determine the change in length (in mm correctly up to two decimal places) of rod AB. A C P 500 mm В E 400 mm F
For the beam and loading shown, determine the reaction at the roller support. Assume that the flexural rigidity El of the beam is constant. (Round the final answer to two decimal places.) Given: w2wo A -L- { x = 0, y = 0} { x = 0, y = 0} {x=L, y = 0} The reaction at the roller support is 0.37 wo Lt. B
The rigid bar AB, attached to two vertical rods as shown in Fig. is horizontalbefore the load P is applied. Determine the maximum value for P If the stress must not exceed: 160 MPa for steel and 80 MPa for Bronze. Then determine the vertical movement of P. STEEL Lm A-400 mm E-200 GPa BRONZE L-5m A-500 mm E-80 GPa 3m