Determine the strain if stress value is 33 MPa and modulus of elasticity is 80 MPa
Q: two span beam subjected to shear and flexure only is reinforced as follows: SECTION @ MIDSPAN @…
A:
Q: 1200 kN, M=D1800 kN.m and f =28 MPa. Check the adequacy of the section. 500 mm 60mm gure1 80 29 mm…
A:
Q: 1- What are the differences between torsion and tension tests? 2- Which engineering applications do…
A: 1st Answer:- The tensile and the torsion are two different mechanical properties to be analysed in…
Q: What is the difference between instantaneous and additional sustained load deflections? What are the…
A: Immediate Deflection Long-term Deflection Deflection occur after construction or casting and…
Q: Q3: Q3/ A 300x500 mm column as shown in the figure below. If P= 1200 kN, M,=1800 kN.m and f =28 MPa.…
A:
Q: if the allowable 6tresses are St = 20Mpa and 6c = 8UM Pa, cdetermine the value of X such that w be…
A:
Q: The bolted type connection will be used to assemble the given steel members. Determine the safe load…
A:
Q: While visiting Cape Canaveral, we came upon an engineer digging a hole. "How deep is that hole?" We…
A: Following is required answer :
Q: SITUATION. A closed cylinder of radius 10 cm, height of 30 cm is filled with water. If the cylinder…
A:
Q: 4.49. If 100 m³/s of water flows in a channel 8 m wide at a depth of 0.9 m, calculate the downstream…
A:
Q: monolith floor framing plan is shown in the figure. the column are 300 mm square, girderes are 250…
A: Dead load include self weight of slab + finish load+ ceiling load + partition loads. Live load =4.8…
Q: A triangular slab ABC shown in Fig. 15.7 is simply sUpPorted along edges Aß and AC but has a free…
A:
Q: concrete floor slab 100mm thick is cast monotholic with concrete beams 2.0 m on centers. the beams…
A:
Q: L
A:
Q: A simple curve has a radius of 220 m and angle of intersection of 128°. The curve is to be shifted…
A:
Q: Calculate the nominal shear strength (kN) of 4-legged stirrups 12-mm-diameter, spaced at 220 mm on…
A: Based on the different types of specifications, first we will calculate the width of the beam. To…
Q: Bond is IOU with face value (V), coupon rate (b), no. of payment periods/year (C). dividend (1), and…
A: Given bond = 10000 bond time = 5 years interest = 6%
Q: The base of a solid in the first quadrant are bounded by the line 4x + 5y = 20 and the coordinate…
A:
Q: A two span beam subjected to shear and flexure only is reinforced as follows: Given: Stirrup…
A:
Q: Q2: Design a round spiral column to support an axial dead load Po of 240 k and an axial live load P,…
A:
Q: Q-4: A precast concrete pile of size 50 cm x 50 cm is to be driven into clay strata whose unconfined…
A:
Q: Bar AB rotates as shown with an angular velocity equal to 10 rad/s. Assume AB ha a length of 500mm…
A:
Q: 1m 10 kN 5 kN/m 2m 2m- 4m A beam with a hinge is loaded as above. Draw the shear force and bending…
A:
Q: A storm sewer inlet collects flow from a with the following characteristics: – Area=4ac. – Land use:…
A: Given, Area (A) - 4 acres Length (L) = 800 ft Slope (Y) = 1%
Q: 2.) Find also the principal stresses oi and oz and its orientations 0p1 and 0p2 from the x-axis.…
A:
Q: A barge is loaded with 150 tons of coal. The weight of the empty barge in air is 35 tons. If the…
A: Given data Coal weight C = 150 tons Weight of empty barge B = 35 tons Width of barge b = 18 ft…
Q: 3/76 Determine the speed v at which the race car will have no tendency to slip sideways on the…
A: Determine the speed u at which the race car will have no tendency to slip sideways on the banked…
Q: Underneath a conventional plug flow reactor and a plug flow reactor with tapered aeration that both…
A: PLUG FLOW REACTOR & PLUG FLOW REACTOR WITH TAPERED AERATION: The input and recirculated sludge…
Q: A vertical parabolic sag curve of Laon Laan underpass has a grade of -4% followed by a grade of +2%…
A: We know that ; r = g2 - g1L L = g2 - g1r where ; g2 = 2 % = 0.02 g1 = - 4 % = - 0.04 r = 0.6 % =…
Q: C
A: A dummy activity is used to connect network representation to maintain the logic of network diagram.…
Q: Q 1 .An aquifer has following different formations, their thickness and Hydraulic conductivity are…
A:
Q: 1. A body Cnsists of aright Circular Soli d Cone of haight a Solid hamisphere of 40mm 40mm and…
A: step 1-
Q: For the conditions shown in schematic 1m figure, find the force F required to lift the Absolute…
A:
Q: On the first six tests of Junlie's Mathematics subject, his scores were 92, 78, 86, 92, 95, and 91.…
A:
Q: Refer to Fig. STA-002. Determine the torque (kN-m) at D W 8 kN/m P =40KN 2.5m 0. 3m Fig. STA-002 O…
A:
Q: A two span beam subjected to shear and flexure only is reinforced as follows: SECTION @ MIDSPAN @…
A:
Q: A coin purse has 3 OLD one-peso coins and 7 NEW one-peso coins. Suppose you randomly pick a coin and…
A: Given data: 3 old coins 7 new coins
Q: Which of the following is/are true regarding a project network? I. The probability of completing the…
A:
Q: A 470 mm-diameter, non-slender, spiral column is symmetrically reinforced with 8-16 mm vertical…
A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…
Q: simply supported beam
A:
Q: Find the value of normal stress if force applied is 2 N and cross sectional area 2 mm2
A: Stress is the internal resistive force offered by material against the external load applied on it.…
Q: Use STAAD.Pro to determine the support reactions on the frames below and draw the bending moment…
A: QUESTION 1 You Can find support reactions in the top right table BENDING MOMENT DIAGRAM
Q: Groundwater ingress from a mine and contaminated water from an industrial plant is pumped into a…
A:
Q: n 2: If the force Fx = 100 k s of the plate =t 1 in
A:
Q: Design the shear reinforcement for the beam shown if it carries a service dead load of 36 kN/m and a…
A:
Q: RODS AC AND BC ARE USED TO SUSPEND THE 100 KN WEIGHT. IF EACH ROD IS MADE OF A MATERIAL FOR WHICH…
A: The given data is shown below: Weight=100 kNAverage normal stress=200 MPa
Q: A singly reinforced rectangular beam 300 mm wide and 600 mm deep is subject to a factored shear…
A: Nominal Shear Strength: The strength which is required by the element or fiber per unit surface area…
Q: ater profile created by an obstruction below and conveys a discharge of 2
A:
Q: Repeat the previous problem, only now the driver of car A is traveling at VA = 130 km/h as it passes…
A:
Q: If a pre-jump depth and post-jump depth in a hydraulic jump is 0.620 m and 4.980 m respectively, The…
A:
Step by step
Solved in 3 steps
- The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.Determine the value of stress if modulus of elasticity is 62 MPa and strain value is 0.0025Problem: A steel rod with a cross-sectional area of 180 mm2² is stretched between two fixed points. The tensile load at 25°C is 3,600N. Assume thermal coefficient equal to 11.7 x 106 mm/ (mm°C) and E= 200 GPa. a. What is the temperature at which the stress will be zero? b. What is tthe temperature at which the compressive stress will be 48 MPa?
- (a) Determine the elastic strain when a stress of 80 MPa is applied to the model (rheological ) shown below. (b) Compute the total strain after a month (30 days). 5. 20 GPa |200 GPA.days 40 GPa | 300 GPA.days1. Given the data, plot the stress-strain diagram 2. Determine the proportional limit 3. Determine the modulus of elasticityFind the modulus of elasticity Stress=2 MPa Strain=0.1
- A steel bar, whose cross section is 0.60 inch by 4.10 inches, was tested in tension. An axial load of P = 31,025 lb. produced a deformation of 0.115 inch over a gauge length of 2.10 inches and a decrease of 0.0080 inch in the 0.60-inch thickness of the bar. a. Determine the lateral strain. b. Determine the axial strain. c. Determine the Poisson’s ratio v. d. Determine the decrease in the 4.05-in. cross-sectional dimension (in inches).A steel rod with a cross-sectional area of 188 mm2 is stretched between two fixed points. The tensile load at 23°C is 6,332 N. What will be the stress at -15°C ? Assume a = 11.7 x 10-6 m/(m.°C) and E = 198 GPa. Answer must be in MPa.2. A steel bar, whose cross section is 0.55 inch by 4.05 inches, was tested in tension. An axial load of P = 30,500 lb. produced a deformation of 0.105 inch over a gauge length of 2.05 inches and a decrease of 0.0075 inch in the 0.55-inch thickness of the bar. * Determine the lateral strain. Your answer Determine the axial strain. Your answer Determine the Poisson's rati v. Your answer Determine the decrease in the 4.05-in. cross-sectional dimension (in inches). * Your answer
- A mild steel bar of square cross-section 40 mm x 40 mm is 400 mm long it is subjected to a longitudinal tensile stress of 440 N/mm² and lateral compressive stress is 200 N/mm² in perpendicular directions. E = 2 x 105 N/mm², μ = 0.3. What is the approximate elongation of the bar in the longitudinal direction?Determine the modulus of elasticity of material that has proportial stress 110 MPa and proportional strain 0.002Shown is a composite plate joined together by rivets. The components consist of two tension bar plates that is ¾ X 4 inch and riveted together by two splice plates which is 0.8 X 6 inch. Each rivet has a diameter of 25.4 mm. Considering that the allowable stress for the tension bar plates and splice plates is σ=20.0 ksi, the allowable shear stress for the rivets is σ=25.0 ksi and the allowable bearing stress on the rivets and splice plates is σ=25.0 ksi. What will be the maximum permissible load P such that none of the allowable stresses will be exceeded?