Please answer part b Determine the required stirrup spacing for a 10mm diameter U stirrups. In a reinforced concrete beamwith effective depth of 400mm to carry the next shear of 164KN if fyh=270MPAA Rectangular beam has b= 250mm and d= 330mm, fy= 414MPA fc= 20.7MPa Determine a.) themaximum design moment if the beam is singly reinforced b.) the required steel area if thebeam is required to carry a dead load moment of 50kn.m and a live load moment of 30KN.mUse 2010 NSCP

Design moment capacity : The greatest moment carrying capacity for the beam that is regarded safe…

Determine the required stirrup spacing for a 10mm diameter U stirrups. In a reinforced concrete beam with effective depth of 400mm to carry the next shear of 164KN if fyh=270MPA A Rectangular beam has b= 250mm and d= 330mm, fy= 414MP fc= 20.7MPA Determine a.) the maximum design moment if the beam is singly reinforced b.) the required steel area if the beam is required to carry a dead load moment of 50kn.m and a live load moment of 30KN.m Use 2010 NSCP

Determine the required stirrup spacing for a 10mm diameter U stirrups. In a reinforced concrete beam with effective depth of 400mm to carry the next shear of 164KN if fyh=270MPA A Rectangular beam has b= 250mm and d= 330mm, fy= 414MP fc= 20.7MPA Determine a.) the maximum design moment if the beam is singly reinforced b.) the required steel area if the beam is required to carry a dead load moment of 50kn.m and a live load moment of 30KN.m Use 2010 NSCP

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

AT:Design the steel reinforcement for flexural for the beam shown in the kN fig.below The dead load on the beam is 100 (not include self weight) & the live load is 200KN. useØ25mm& Use effective cover in top& bottom=60mm, use fc' = 27.6 Mpa, fy= 414Mpa. Ptive=200KN kN D.L= 100 d= 550mm 275mm 3m Зт
Draw the stress envelops (shear and moment) for the beam below subjected to the following loads SFD WD= loku/m BMD Sm DEAD LOAD шно вклу/т 8 LINE LOAD 20KN 30kn-m -40k41 RESULTS FROM SEISMIC ANALYSIS WL₂= 13 PD=ISKN 2m B -18 kN/m * -12KN G IS KN-M C
Where is/are the location(s) of the maximum transverese shear stress? A simple I-beam is loaded as shown. 20 mm P KN PKN PKN Į Į -C B с D L/4 m L/4 m Midspan at point C Roller at E at the NA Section B at the top fiber Pin A at point C Midspan at point D Roller E at point D L/4 m L/4 m OE 20 mm 20 mm- 250 mm 150 mm 150 mm A
The beam shown has the following properties: concrete cover=40mm, ds= 10mm, f'c=21 MPa, and fy=280 MPa. Determine the ultimate moment capacity of the beam in kN-m. Determine also the type of failure and the beam condition (under-reinforced, over-reinforced or balanced condition) 250mm 5-ø16mm h =450mm 50mm
the rectangular beam having a dimension of b= 320mm, h=460mm with 4pcs-28mm diameter reinforcing bars, determine the following a) cracking moment if fr =3.4MPa, b) stressed if moment (M)=42kN-m and n=9
Where is/are the location(s) of the maximum compressive flexural stress? A simple I-beam is loaded as shown. 20 mm P KN PKN P KN B 20 mm- B с D L/4 m L/4 m L/4 m Pin support at the NA Midspan at point B Mid span at point D Midspan at the top fiber Roller support at top fiber Section D at the top fiber Section C at +170 mm from the NA L/4 m 20 mm C 250 mm 150 mm 150 mm D A
S f A structure is to be built as shown supporting a uniform load of 18 kN/m. The location for the supports at A and B has been determined. The connection at C may be placed anywhere along the member AD 18 kN/m A C D 3 m B L -7 mi -5 m- If the allowable bending stress for member AD is 8 MPa, which among the choices gives the most economic section? Select the correct response: 275 mm x 550 mm 250 mm x 500 mm 300mm x 600 mm 225 mm x 450 mm rigid
c) The three suspender bars are made of A-36 steel and have equal cross-sectional areas of 450 mm² .Determine the average normal stress in each bar if the rigid beam is subjected to the loading shown. A B C 80 kN 2 m 50 kN D E F -1m--1m--1 m--1m-|
4-1 Figure P4.1 shows a simply supported beam and the cross section at midspan. The beam supports a uniform service (unfactored) dead load consisting of its own weight plus 1.4 kips/ft and a uniform ser- vice (unfactored) live load of 1.5 kips/ft. The con- crete strength is 3500 psi, and the yicld strength of the reinforcement is 60,000 psi. The concrete is normal-weight concrete. Use load and strength- reduction factors from ACI Code Sections 9.2 and 9.3. For the midspan section shown in Fig. P4-1b, compute M, and show that it exceeds Mu- Wo = 14 kips/it plus weight of beam WL - 1.5 kipa/it (a) 20 ft 21.5 in. 24 in. (b) 3 No. 9 bars 12 in. Fig. P4-1
An RCC beam 400*600 (effective depth) is reinforced with 4 no. 25mm diameter bar the beam is subjected to BM 150KNm. find the stress setup in steel and concrete. Consider M20 Fe415
a om long simply supported beam has a width of 350mm and overall depth of 470mm the beam is reinforced with 2- 28mm compression bars and 4-28mm bension bars each located 70mm from the extreme concrete fber. concrete strength is 21 Mpa and yield strength is 420Mpa determine the ff. depth of compression block ultimate moment capacity of the beam derermine the addinonal concentrated ive load that can be acpled at midspan if the dead load inclusing the weight if the beam is 20KN m Select the corect response a- 82.79mm, Mu- 320 SSKN-m, Pu Ba57KN a- 165.58mm, Mu - 328 13KNm, Pu -136 88KN O a 110.81mm, Mu - 351 47KNm, Pu 15o.09KN O a- 110.81mm, Mu 316 23KNM, Pu - 86 BKN a- 82 79mm, Mu- 320 5SKNm Pu1537KN a 165 semm, Mu 295 32KNM, Pu136. 8BKON a- 82.79mm, Mu- 356.17KN m, Pu153 7KN a- 165.58mm, Mu - 295 32KN-m, Pu =78 0SKN a 110.81mm, Mu 316 33KNM, Pu 150.89KN
Check the adequacy of the isolated T-beam shown below according to ACI Code requirements and determine the design flexural strength (Moment) for it, use: • f = 20 MPa. • fy = 420 MPa. Effective depth d = 610 mm. • Reinforcement is 6Ø25mm (ABar = 490 mm?). 500 mm 125 mm 700 mm 6Ø25mm 250 mm