Determine the required qty. rebar for this slab with a clear dimension of 5.6m x 7.8mSHORT SPAN (BAR SPACING IN MM.)LONG SPANBOTTOM BARS(88)BOTTOM BARSTOP BARS CONT.(TBC)(BB)300200#10 @250SLABMARK$17THICK- BAR ØNESS(7")2V6 400x700160UNLESSOTHERSSPECIFIED12TOP BARS DISCONT.(TBD)2H12 400x600$17(160)2H14 400x6002V11_400x65040C1TOP BARS DISCONT.(TBD)(BAR SPACING IN MM.)TOP BARS CONT.(TBC)#10 @175REMARKSTWO-WAY

Answered: Image /qna-images/answer/ea923a12-a059-47c8-abbc-c0c23defe84c.jpg

Determine the required qty. rebar for this slab with a clear dimension of 5.6m x 7.8m SHORT SPAN (BAR SPACING IN MM.) LONG SPAN BOTTOM BARS (88) BOTTOM BARS TOP BARS CONT. (TBC) (BB) 300 200 SLAB MARK $17 THICK- BAR 2 NESS (7) 2V6 400x700 160 UNLESS OTHERS SPECIFIED 12 TOP BARS DISCONT. (TBD) 2H12 400x600 $17 (160) 2H14 400x600 2V11_400x650 40 C1 TOP BARS DISCONT. (TBD) #10 @250 (BAR SPACING IN MM.) TOP BARS CONT. (TBC) #10 @175 REMARKS TWO-WAY

Determine the required qty. rebar for this slab with a clear dimension of 5.6m x 7.8m SHORT SPAN (BAR SPACING IN MM.) LONG SPAN BOTTOM BARS (88) BOTTOM BARS TOP BARS CONT. (TBC) (BB) 300 200 SLAB MARK $17 THICK- BAR 2 NESS (7) 2V6 400x700 160 UNLESS OTHERS SPECIFIED 12 TOP BARS DISCONT. (TBD) 2H12 400x600 $17 (160) 2H14 400x600 2V11_400x650 40 C1 TOP BARS DISCONT. (TBD) #10 @250 (BAR SPACING IN MM.) TOP BARS CONT. (TBC) #10 @175 REMARKS TWO-WAY

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

5:57 Jul 26 11:00 AM ९४ Find the centroid of given composite figure. Set- up the reference axis on the lower left corner. Radius = 1.5" L Send d Favorite ||| 8" Edit U 3" Delete (23) 4 ✓ ….….. More
The recommended steel ratio for a slab having thickness of 125 mm is 0.00215 determine the required area (mm2) of main reinforcement bars using 12 mm dia. bars and minimum clear cover. Round of your answer to a whole number, no need to write down the unit.
GIVE 10 DISADVANTAGES OF USING HOLLOW BLCOKS.
Qs. Show the compressive strength of the PET(Polyethylene Tetraphthalate ) filled with soil and used as a brick in compressive test machine ,When fractured load is 90 KN is for bricks and 230 KN is for PET unit, analysis of CTM data as an strength If you do not know the answer please skip allow others, dont post wrong I will downvote for sureNote-This is not a writing assignment
+ „blackboard.com/ultra/courses/_96287_1/cl/outline Question Completion Status: 4 8 9 10 A two span beam subjected to shear and flexure only is reinforced as follows: SECTION @ MIDSPAN @ FACE OF SUPPORTS TOP BARS 2-020 mm 5-Ø20 mm BOTTOM BARS 3-020 mm 2-020 mm Given: Stirrup diameter, ds = 10 mm Concrete fc = 21 MPa Steel rebar = 415 MPa Stirrup fy = 275 MPa %3D Beam size b xh = 270 mm x 450 mm Assume all bars laid out in single layer. Calculate the following: Tensile steel ratio in positive bending at midspan = (in 5 decimal places) kN m (nearest whole Design Moment strength of section at midspan for positive bending = 32°C Light rain ^ O O G ) ENG 1:42 pm ロ

Ans - 8.44lb
Internal effortsfeatures on a 750 mm sheet wide (made of ASTM A36 steel) were determined using a software basic structure analysis. The effort characteristic requester from a usage overhead is equal to 1260kN. Calculate the thickness needed for the plate? Adopt fyk = 250 MPa and fuk = 450 MPa.Please help Expert sir
(structural analysis) Calculate and draw: FBD, NFD, SFD and BMD.
Pls help.
Answer the ff in complete solution and draw an fbd
need asap pls. thank u
Problem 1: Calculate Mn and check the minimum steel limit f'c =4 ksi, fy 60 ksi. 2.5" 25" 6-#9 12" 3.5" 4" 25"