Determine the reactions (forces and moments) at the journal bearings A, B, and C for the loading shown on the pipe. Note 1: On Canvas, enter the magnitudes only. Give your answers with three significant figures. Note 2: Include a description and the units in the detailed solution 2 ft 1 ft 4 B 200 lb 2 ft 30 lb-ft

Q: Which among the following is a forming process in which thickness of the metal plate is decreased by…

A: Metal forming processes are the processes in which plastic deformation of the material is done in…

Q: 18. How far off from the center of the support is the center of the two holes in the bosses of the…

A: 18)    Distance=4.2-0.66                   =3.54 in

Q: how o create all parts list after the drawing ?

A: Given question: how to create all parts list after the drawing ?

Q: lease write a precise overview/description of the precision tweezer below specifically for each…

A: Given Data : Precision tweezer

Q: If 17 welders can complete a job in 134 hours, how long will it take for 21 welders to do the same…

A:

Q: I have three parts that I need answered pertaining to the print provided below.   Do the dimensions…

A: It is mentioned in the drawing specification that “dimensions and tolerances apply before the…

Q: What kind of font is typical for usage in engineering diagrams?

A: To find: The type of font used in engineering diagrams.

Q: Q3: Mark the Following True or False 1. Hidden lines are used in sectioned area when they are needed…

A: 1.TRUE 2. TRUE 3.TRUE 4.FALSE 5. FALSE 6.FALSE 7.TRUE 8.FALSE 9.FALSE 10.FALSE 11.TRUE 12.TRUE…

Q: In which of the following casting process, the melting pot is an integral part of the machine. * O…

A:

Q: What are the different types of force? Applied Tension Gravitational Spring Air Resistance Normal…

A: (I) Force has been classified on the basis of contact which is as follow 1. Contact force:- These…

Q: R L2 (Side view) (End view)

A: Given data: α (Bend angle) =70° Kba (Strecth factor) =0.33  t  (Stock thickness) = 0.3" R (Width…

Q: can you please write it in a proper way?

A:

Q: With reference to the drawing callout in figure 5 below, which part(s) would 'pass' or 'fail' along…

A: Data given-  Dimensions of standard size  0.25±0.01 So tolerance is equal to 0.02  And the upper…

Q: 1.00 1.38 3.38 38 2.00

A: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

Q: Write TRUE is the statement/s is True. If the statement is false, identify the word/s that makes the…

A: The chip compression ratio can be defined as the ratio of the chip thickness and uncut chip…

Q: FORTUNE FAVOURS THE BRAV

A: A week ago our little villa was invaded by fear-based oppressors. There was dread in the seniors.…

Q: what is the scale if a line is 10 inches but is  drawn 5 inches long.

A: Finding scale if a line is 10 inches but is  drawn 5 inches long.

Q: short notes on any two types of chips formed during metal cutting operation

A: Metal cutting is defined as "the act of eliminating undesirable material from a block of metal in…

Q: This is no answer sorry the answers are offered A B C or D

A:

Q: A piece of 12-gauge sheet metal is 7⁄64 inch thick. A stack of sheet metal is171⁄2 inches thick. How…

A: Given12 guage sheet metal sheet thickness t=7/64 inchthickness of stacked sheets t2=171 2inches

Q: Question attached

A: (a) Relative humidity is the ratio of the partial pressure of water vapour in the mixture to the…

Q: PART VI. Given that f(x,y) = (x +y)/2k, where x=-1,1,2 and y= 0,2,4 1. Find k 2. Find the marginal…

A:

Q: Draw the Mohr stress circles for the states of stress at a point given in the figures below. For (a)…

A: Draw the Mohr stress circles for the states of stress at a point given in the figures below.  To…

Q: What type of lines can be used in a drawing to show that part of an object has been removed ?

A: Solution : There are two types of line which are used to show the removed part of an object : Break…

Q: What's the answer C onwards with working and correct answer and can you label it please as I have…

A: The ideal diesel cycle does not occur in practical life because the losses are not eliminated in…

Q: I need answers for 7,8, and 9,

A: A 0.250”X0.250” square hole.

Q: C) What is the maximum possible mass flow rate that the pump can produce?

A:

Q: Choose the correct word to complete the -5 following sentence: The fault was.......... .None of the…

A: Correct answer: (c) undetected

Q: A 15-meter long beam-tank assembly supports the loading shown in addition to its weight, which is a…

A: The outer diameter of cylinder is .The inner diameter of cylinder is .

Q: I need this part answered according to the disrections provided in the image.

A: Match each of the following terms to the phrase that describes it

Q: Please give the details explanation of the answer

A:

Q: Which of the following process for sheet metal cutting, the cut piece is the desired part? Shearing…

A:

Q: I need help answering this Review Activity

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: Quenching is a process that can reduce the grain size and form a lot of grain boundaries in the…

A: Quenching: In this process metal is heated above its recrystallization and than cool it rapidly. The…

Q: With reference to the drawing callout in Figure 4 below, which part(s) would 'pass' or 'fail'…

A:

Q: 10) Define the slip angle.

A: The angle between the direction of the wheel in which it is pointing and the direction in which it…

Q: Write the Column Formulas?

A: Types Critical load Both ends hinged π2EIl2 one end hinged other end fixed 2π2EIl2 both ends…