Determine the rating of the primary fuse and the minimum ampacity rating of the primary and secondary conductors for a 5 MVA dry-type transformer with a primary of 13.8 kV and a secondary of 600v, three-phase 4wire. Choose the correct answer: a. I Line 314.145amps, I Load 6,21.2amps, 450amp fuse b. I Line 261.79amps, I Load 6,021.2amps, 350amp fuse c. I Line 344.15amps, I Load 6,021.2amps, 450amp fuse

Determine the rating of the primary fuse and the minimum ampacity rating of the primary and secondary conductors for a 5 MVA dry-type transformer with a primary of 13.8 kV and a secondary of 600v, three-phase 4wire. Choose the correct answer: a. I Line 314.145amps, I Load 6,21.2amps, 450amp fuse b. I Line 261.79amps, I Load 6,021.2amps, 350amp fuse c. I Line 344.15amps, I Load 6,021.2amps, 450amp fuse

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter13: Transmission Lines: Transient Operation

Section: Chapter Questions

Problem 13.24P

See similar textbooks

Similar questions

A single-phase l0-kVA,2300/230-volt,60-Hz two-winding distribution transformer is connected as an autotransformer to step up the voltage from 2300 to 2530 volts (a) Draw a schematic diagram of this arrangement, showing all voltages and currents when delivering full load at rated voltage. (b) Find the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the rated values as a two-winding transformer. How much of this kVA rating is transformed by magnetic induction? (C) The following data are obtained from tests carried out on the transformer when it is connected as a two-winding transformer: Open-circuit test with the low-voltage terminals excited: Applied voltage =230V, input current =0.45A, input power =70W. Short-circuit test with the high-voltage terminals excited: Applied voltage =120, input current =4.5A, input power =240W. Based on the data, compute the efficiency of the autotransformer corresponding to full load, rated voltage, and 0.8 power factor lagging. Comment on why the efficiency is higher as an autotransformer than as a two-winding transformer.
A single-phase 50-kVA,2400/240-volt,60-Hz distribution transformer has a 1-ohm equivalent leakage reactance and a 5000-ohm magnetizing reactance referred to the high-voltage side. If rated voltage is applied to the high-voltage winding, calculate the open-circuit secondary voltage. Neglect I2RandGc2V losses. Assume equal series leakage reactances for the primary and the referred secondary.
Rework Problem 3.14 if the transformer is delivering rated load at rated secondary voltage and at (a) unity power factor, (b) 0.8 power factor leading. Compare the results with those of Problem 3.14. -
Using the transformer ratings as base quantities. work Problem 3.14 in per-unit.
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
Consider the oneline diagram shown in Figure 3.40. The three-phase transformer bank is made up of three identical single-phase transformers, each specified by X1=0.24 (on the low-voltage side), negligible resistance and magnetizing current, and turns ratio =N2/N1=10. The transformer bank is delivering 100 MW at 0.8 p.f. lagging to a substation bus whose voltage is 230 kV. (a) Determine the primary current magnitude, primary voltage (line-to-line) magnitude, and the three-phase complex power supplied by the generator. Choose the line-to-neutral voltage at the bus, Va as the reference Account for the phase shift, and assume positive-sequence operation. (b) Find the phase shift between the primary and secondary voltages.
Find the following : 1.Ripple Voltage (vpp) 2. Zero-to peak ripple(Vop) 3.secondary winding of the transformer high line and low line
4. A single-phase, 1000-kVA, 2400/8000-V, 60HZ distribution transformer has the following parameters: Resistance of the 2400-V winding: R1 = 2.75 2 Resistance of the 8000-V winding: R2 = 29.4 2 Leakage reactance of the 2400-V winding: X1= 1.8 Q Leakage reactance of the 8000-V winding: X2 = 20 2 Exciting admittance on the 2400-V side: 0.002 - j0.008 S %3| Draw the equivalent circuit referred to the high voltage side of the transformer. a. b. Draw the equivalent circuit referred to the low voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits. 5. The transformer in Problem 4. is supplying a rated load of 1000-kVA at a rated secondary voltage of 8000 V and at 0.8 power factor lagging. Neglecting the transformer exciting current, determine the input terminal voltage of the transformer on the low-voltage side.
A fault occurs at point F of the system in the figure. Calculate the sub-transient current in phase c of machine 1, assuming that the currents before the fault are zero. Both machines have a nominal capacity of 1200 kVA, 480 V, with reactances X”=X2= 11% and X0 = 3.5%. The nominal capacity of each three-phase transformer is 1200 kVA, 480 V Δ/ 2400 V and with reactances X1=X2=X0= 6%. Transmission line reactances are X1=X2=22% and X0 = 35% on a 1200 kVA, 2400 V basis. Neutral grounding reactor reactances are 8% on a kVA and kV basis. of the machines. a) Calculate the fault current if a ground fault occurs in phase a, b) The fault current if it is a line-to-line fault c) the voltage in phase b and c for the line-to-ground fault in phase a .
Three-phase, 50 Hz 34500/10500 /Y connected transformer single-phase visible on the high voltage (primary) windings side Equivalent circuit parameters are given below. Each of the low voltage (secondary) windings of this transformer When a 7.5 ohm star connected resistive load is connected and the rated voltage is applied to the high voltage windings Find the transformer efficiency. Total iron losses of three phases will be taken as 85000 W.
A single-phase 100 kVA, 2400/240 V, two-winding transformer will be used as a step-down auto-transformer in a 2640/2400 V system. The connection diagram of the transformer is given below. Calculate the I1, I2 and Ix currents given in the figure. Compare the kVA values of the auto transformer with the kVA values of two-winding transformers.
The ratings of a single-phase three-winding transformer are as follows:*primary winding: 300 MVA, 14kV*secondary winding: 300MVA, 200kV*tertiary winding: 40MVA, 20kV. The leakage reactances are:*Xps = 0.1 at 300MVA, 14kV*Xpt = 0.16 at 40MVA, 14kV*Xst = 0.14 at 50MVA, 200kV Neglecting the winding resistance and exciting current, calculate Xp, Xs and Xt using 300 MVA and 14kV as the base for the primary winding.