Determine the quantity (volume) of saline water in a steam generator. The heat energy of 1526 kJ is supplied to saline water in the steam generator to heat from 26°C to 114°C for the generation of water vapor, Take the density & specific heat of the solution as 1026 kg/m3 & 3.3 J/kg°K respectively. Solution: Change in Temperature (in K) Mass of the saltwater (in kg) Quantity (Volume) of saltwater (in m3)

Determine the quantity (volume) of saline water in a steam generator. The heat energy of 1526 kJ is supplied to saline water in the steam generator to heat from 26°C to 114°C for the generation of water vapor, Take the density & specific heat of the solution as 1026 kg/m3 & 3.3 J/kg°K respectively. Solution: Change in Temperature (in K) Mass of the saltwater (in kg) Quantity (Volume) of saltwater (in m3)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An auditorium which is 5m wide by 15m long and a ceiling of 3m. The initial air is maintainedby air conditioning units at 101.3kPa and 22°C. At some point the air conditioning unitstopped its operation and the pressure & temperature becomes 105.0773 kPa & 33°C.Assuming the auditorium is empty. Determine the following:a. The mass of air inside, in kgb. Change in Internal Energy, in kJc. Heat gained by the air, in kJ
i need the answer quickly
Explain how you find the P3 and U3 as well for the heat transfer within 2-3
Ms Png works on a piston-cylinder system which contains 0.05 m3 of nitrogen gasinitially at 200 kPa. At this state, a linear spring that has a spring constant of 150kN/m is touching the piston, but no force is exerting on it. Heat is then transferredto the nitrogen gas, causing the piston to rise and to compress the spring until thevolume inside the cylinder increases to 0.25 m3.a) Determine the final pressure inside the cylinder.b) Sketch the system on a P – V diagram.c) Calculate the total work done of the system.d) Deduce the work done against the spring to compress it.Given cross-sectional area of the piston = 0.25 m2Force applied by linear spring, F = kxk = spring constantx = displacement of the piston/spring
The volume of the radiator used in the heating installation of a system is 20 liters. When the radiator is filled with saturated (dry) steam at 120 kPa pressure, the steam inlet and outlet valves are closed. Find the amount of heat transferred from the heater to the burner until the temperature drops to 30 °C. Given in Tables: Vb= 1.428 m3 /kg hb=2683.4 kj/kg for T=30 0C Pd=4.241kPa Vs=0.0010043 m3 /kg Vb=32.93 m3 /kg hs=125.66 kj/kg hb=2556.4 kj/kg
Water is to be pumped from the bottom of a well 20 ft deep with a specific heat of 1 BTU/lbm F is pumped using a 1-hp jet pump. Heat is lost from the whole system at the constant rate of 500 BTU/min. What is the temperature (℉) of the water as it enters the storage tank assuming that the well water is at 35℉?
The radiator of a steam heating system has a volume of 56 dm3 and uses dry saturated steam at a temperature of 160°C. By perfectly closing the inlet and outlet valves on the radiator, the temperature of the trapped steam decreases to an ambient temperature of 20°C as a result of heat transfer to the environment.a) Determine the mass of vapor trapped in the radiator.b) Determine the quality of the steam when the temperature is 20°C.c) Calculate the vapor pressure when the temperature is 20°C
A tank of air is expanded via heat transfer at a constant pressure such that its volume is 2.5 times its original volume. If the initial temperature of the tank was 23 Celsius, what is the amount of heat transfer required for this process in kJ/kg? Calculate this with the following 3 approaches: Constant Specific Heats (use the average temp) The equation as seen on table A-2 Air property tables
2. A vertical piston-cylinder device contains water and is being heated on top of a range. During the process, 65 Btu of heat is transferred to the water, and heat losses from the side walls amount to 8 Btu. The piston rises as a result of evaporation, and 5 Btu of work is done by the vapor. Determine the change in the energy of the water for this process. draw a figure also, and explain each step by step solution.
A rigid tank initially contains 1kg of saturated water vapor (x-1) at T= 120-C. Now, the tank is started to be cooled until the temperature of the water drops to 80-C. During the process the volume of the tank is kept fixed. a) Calculate the mass of the liquid water left inside the tank after the cooling. b) Calculate the amount of heat extracted from the water inside the tank during this proces
At 1 kg copper part, initially a 500K is plunged into a tank containing 4 kg of liquid water initially at 250K. The copper part and water can be modeled as incompressible with specific heat 0.4 KJ/ kgK and 4 KJ/kgK, respectively. For their copper parts and water as the system. Ignore the heat transfer between the system not in surroundings. Write the energy balance equation for the full system including both copper parts and water part. Define the final equilibrium temperature in K for the system Wright the entropy balance equation and deletes terms are not necessary calculate the amount of entropy produced within the tank in KJ/K Due to part d this process is ________________? - internally reversible - internally irreversible -impossible
A rigid 2 ft3 tank with 134a coolant is initially at 100 psia and 40% quality. Heat is transferred to the refrigerant until the pressure reaches 300 psia. There is a paddle wheel that works with a constant torque of 120 lbf ft making 1000 turns, in addition to an electrical resistance that acts with a 220 volt source for a current of 2 A for 13 minutes. Determine a) the amount of heat transferred Answer (Btu) b) the final temperature Answer (* F)