Answered: Determine the pressure change of the…

Name: Determine the pressure change of the differential pressure gauge expre
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Determine the pressure change of the differential pressure gauge expressed in Pa – Pb, express the pressure in inches of oil (Sg = 0.85) Sg = 16.4Sg = 3.45Accite (sg = 0.90)6 pulg8 pulg10 pulg6 pulg6 pulgp = 145.62 Ib/ft3Sg = 6.20

Engineering

Mechanical Engineering

Determine the pressure change of the differential pressure gauge expressed in Pa – Pb, express the pressure in inches of oil (Sg = 0.85)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A particle moving along a straight line has an acceleration which varies according to position as shown. If the velocity of the particle at the position x = -7 ft is v = 6 ft/sec, determine the velocity v when x = 13 ft. a, ft/sec² 9 M -7 0 0 8 x, ft -4 1 11 13
1. ! SHOW COMPLETE SOLUTION ! *pls draw FBD *pls use data give properly : rate will be low if not explained properly Problem 1: The pulleys are frictionless and of negligible weight Find: 1.1 Tension (N) in the cord supporting block B. 1.2 Acceleration at Block A (m/s^2) 1.3 Acceleration at Block B (m/s^2) 1.4 Acceleration at Block C (m/s^2)
V3kg=3.025 m/s Wt=8.644 rad/s
EM, = 0; F3c(3/5)A – 0.5C(4+1} = 0 EF, = 0; 4, +F3c (3/ 5)– C(A+1)=o F3c kN A, kN %3D kN yla) M(KN.m) m v3 V2 kN vl V; = kN x2 x2 M = M3 M3 %3D v2 (C) (d) I| || ||
The following data was collected in a road project: Free haul distance = 50 meters Cost of borrow= 5 pesos per GYm Cost of haul = 0.25 pesos per meter station • Stationing of one limit of free haul = 2+763.12 Stationing of one limit of economic haul = 2+948.03 Assume the ground surface has a uniform slope from cut to fill. STATION AREA CUT FILL 2+440 51 2+740 BALANCING POINT 3+040 69 Compute the length of economic haul. b. Compute the overhaul volume. a. C. Compute the volume of borrow. d. Compute of the volume of waste.
F1: 0318, F2: 1,894, M: 8,942
A hydraulic lift has a maximum fluid pressure of 500 kPa. What should the piston cylinder diameter be to lift a mass of 850 kg. what is the answer? incluide diagram. a. 0.0017 m^2 b. 1.7m^2 c. 0.017 m^2 d. 16.677 m^2
Problem 4: A boat is shown in the figure below. Its geometry at the water line is the same as the top surface. The hull is solid, Is the boat stable? Top surface 5.5 m 0.3 m 2.4 m Water surface 1.5 m Cross section 0.6 m 6,773 FEB 23 rw MacBook Air 80 888 DII F1 F2 F3 F4 F5 F6 F7 F8 F9 ! @ $ & * 1 2 3 4 5 6 7 8 w #
5) Calculations for the red dog food can rolling down the slope in the Rube Goldberg design are as follows (we will name it Step 1): Step 1 (calculations are given): Coefficient of friction → μ = 0.14 Mass of the object → m = 368 gm = 0.368kg Initial height of the object (red can on top of books) → h=8.89, cm = 0.0889 m Slope of the file folder → 0= 14° Travelling Distance by the object = 11.5 inch = 0.292 m And length that the object will travel = h/sin 0 = 0.0889/ sin14° = 0.367 m So, the radius of the object → R = 0.367 -0.292 = 0.075 m Initial Velocity of red can → u = 0 Velocity and Force Calculations for Step 1: -From total mechanical energy conservation: → Initial mechanical energy = final mechanical energy → mg - In case of pure rolling, the velocity of the center of mass: →V=Roo= 0.075 x 14.28 = 1.07 m/s. -Hence the change in force acting on the object for the travel: →F=mgsine = 0.368 x 9.81 × sin14° =0.89 N Step 2: The Selective Step (Step 2) in this design and for the…
FLUID MECH Support your answer with the appropriate solution and diagram. 3. A rectangular raft made of solid timbers (s=0.60) is 3 m wide and 6 m long x 60 cm thick. A man weighing 800 N steps on the edge of the at the middle of one of the longitudinal sides. Determine by how much the thickness of the raft will be depressed below the water surface along the side in mm. A. 10 B. 20 C. 30 D. 40
A long steel rod is placed horizontally between two supports, one at each end. The rod bends a little in the center. Which property of this rod can be used to estimate how much the rod should bend at the center? 1. Its Shear Modulus 2. Its Young's Modulus 3. All of these Moduli can be used to compute how much it bends. 4. Its Bulk Modulus.
Q. 2: Method Planform Design You are to design candidate wings for a sport RC electric aircraft to the following requirements: density: p= 1.2 kg/m³ speed: lift: V. = 13.4 mph = 6 m/s L = 11 oz = 3.0N span: b = 63 in = 1.6 m Assume an elliptic load distribution I(y) = ToV1- (2y/b)² for each of the design cases below. Assume de /da = 2ñ for the wing airfoils. Assume the wing reference line (e.g. fuselage axis) is aligned with the flight direction, so that a = 0°. 2.1) Baseline elliptical wing: Assume a spanwise-constant c = 0.8. a) (Elliptic) Determine the chord distribution c(y) and sketch the planform. b) (Elliptic) Determine agero(y). c) (Elliptic) What will ageom (y) look like if the same cambered airfoil is used all across the span? d) (Elliptic) Determine the induced drag for this wing? What is the lift-to-drag ratio?