Determine the minimum size of glass tube that can be used to... Determine the minimum size of glass tube that can be used to measure water level if the capillary rise in the tube is restricted to 5mm. Consider surface tension of water in contact with air as 0.073 N/m

Determine the minimum size of glass tube that can be used to... Determine the minimum size of glass tube that can be used to measure water level if the capillary rise in the tube is restricted to 5mm. Consider surface tension of water in contact with air as 0.073 N/m

Name: Determine the minimum size of glass tube that can be used to...Determ
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Determine the minimum size of glass tube that can be used to...Determine the minimum size of glass tube that can be used to measure water level if the capillary risein the tube is restricted to 5mm. Consider surface tension of water in contact with

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A door in the side of a tank is 3.1 m wide and 5.7 m high the tank is filled with oil of relative density 0.78 to a position 1m above the top of the door. What is the line of action of the force from the surface in meters.
If the viscosity of water at 68 oF is 0.01008 poise, then its absolute viscosity expressed in terms of pound-second per square feet (lb-sec/ft^2) must be
Directions: Solve the following problems completely, and make a detailed solution. Any incompletesolution arriving at such answers will never be considered. A barrel contains a 15 cm layer of oil of density 5.88 kN/m3 floating on water that is 30 cm deep. What is the gauge pressure in mmHg at the oil-water interface?
To measure the water depth in a large open tank with opaque walls, an open vertical glass tube is attached to the side of the tank. The height of the water column in the tube is then used as a measure of the depth of water in the tank. (a) For a true water depth in the tank of 3ft, make use of the following equation (with 0 = 0-degree) to determine the percent error due to capillarity as the diameter of the glass tube is changed. Assume a water temperature of 80°F. Show your result on a graph of percent error versus tube diameter, D, in the range 0.1 in.
Solve it
Compute the capillary effect of immersion in mercury of a glass tube of 6mm internal diameter given the surface tension value is 0.51N/m, the specific gravity value is 13.55 and the angle of contact is 140 degrees. Express the answer in the appropriate SI unit.
Engineers investigate the compressibility of fluid for the aircraft hydraulics. You are required to calculate the change in volume of 2litres of water if the pressure on the water is increased from 4 atmospheric pressure to 100atmospheres. Take the isothermal bulk modulus of water to be 2 x 20" atmospheres.
cylinder 12 cm SA A piston 11.96 cm diameter and 14 cm long works in a diameter. A lubricating oil which fills the space between them has viscosity 0.65 poise. Calculate the speed at which the piston will move through the cylinder when an axial load of 0.86 kg is applied. Neglect the inertia of the piston. 0-36 KgwE
Geotechnical
If the barometric pressure is 100 kPa, convert 10 MPа: Match each item to a choice: To psig To КPaa To in Hg absolute To psia Choices: : 2982.79 : 1436.27 : 1877.43 : 10101.325 : 2952.87 : 1450.78 : 1463.08 : 9898.68 : 1587.21 : 10000
Solve it
For a liquid with the contact angle of 53.6 degrees and surface tension of 0.075 N/m, capillary rise is 2.50 m. What is the expected capillary rise in meters if the liquid is replaced with another with a contact angle of 12.7 degrees and a similar surface tension? (answer should be accurate to 2 decimal places) Answer: