Determine the magnitude of the vertical reaction force at D. Assume a = 4.9 ft, b = 9.8 ft, c = 19.6 ft, w = 1060 lb/ft, and P = 3000 Ib. P w A D a Answer: D= i Ib

Q: which are the main instrucations used in FAPT-TURN? Cutting area definition?

A: The instruction used in FAPT-TURN can be given as,

Q: Identify the number of spur gears available in a Single Purchase Crab Winch a. One b. Three c. Four…

A:

Q: It carries the cutting tool and precisely controls its movement either parallel to the ways ,called…

A: Option d is correct.

Q: Complete the following table for 7 types of Engineer’s Hammers.        Types                 Hand…

A:

Q: is used to cut machine other material. O Chromium steel Nickel steel O Martensitic tool steel O Tool…

A: To find the material that are used to cut machine other material .

Q: 44. Bigger diameter end mill cutting tool is preferred during milling operation. Select one: True O…

A: In general, milling is a machining process in which the rotary motion of the cutter is used to…

Q: Angle between side cutting edge and axis of tool is known as: * Back rake angle Side rake angle Side…

A:

Q: O b. tail stock O c. bed

A: Given Data→ Housing Driving pulleys Back gears

Q: The __________ square has a moveable inch-graduated blade. Select one: A. SPEED SQUARE B. FRAMING…

A: The combination square has a movable inch graduated blade.

Q: cutting edge a

A: ANSWER- SIDE CUTTING EDGE ANGLE

Q: 3. (a) In the set-up shown, if the support columns are removed, what will happen to the see-saw?…

A:

Q: QUESTION 2 If you have to precisely rotate your workpiece, which is held on an indexing head, by a…

A:

Q: Up milling operation is performed for finishing cut. Select one: True False

A:

Q: In a single cylinder reciprocating engine, the primary unbalanced force is maximum

A: In a single cylinder reciprocating engine, there is one primary and one secondary unbalanced force.

Q: True or False: The BREAK command requires two separate points when breaking a circle.

A: The BREAK command is used to break the selected object between two points.

Q: 6. Approximate a spindle speed of 1000 rpm into rad/s. Spindle diameter = 200 mm 2.25 rad/s .16 mm/s…

A:

Q: Center drilling operation performed on lathe machine uses a single-point cutting tool. Select one:…

A: Answer is false

Q: When it comes to finding the moment arm, you must use the distance of the line from the pivot to the…

A: Explanation When it comes to finding the moment arm, you must use the distance of the line from the…

Q: What kind of endmill has many smaller teeth meant to distribute the load to reduce vibration during…

A: Select the endmill as below features: Utilize a bigger endmill with a bigger center measurement.…

Q: Name the operation which is enlarges the top portion of drilled hole with tapered shape? a. Step…

A: The process of creating a V-shaped tapered edge near the surface of a hole is known as…

Q: Describe and sketch open drill jigs with its components

A: Open type jig , in which the top plate is arrange to swing about a fulcrum point , so that it is…

Q: What are Solid Noncircular Shafts?

A: Shafts are the rotating members of machines that transmit power and torque. Shafts are of two types.…

Q: The positive rake angle in a single point cutting tool is used to cut non-ferrous metals and low…

A: Positive rake angle is used to reduce shear strain, low power consumption, low cutting force, Less…

Q: Identify the side rake angle (in degrees), from the following single point tool signature…

A: The tool signature of a single point cutting tool is mentioned below (i) Back rake angle(ii) Side…

Q: Identify the name of the milling machine operation in which the cutting takes place by both the end…

A:

Q: The rate of metal removal in drilling is determined as the product of the drill cross-sectional area…

A: Metal removal rate in drilling is given by:- πd^2×fN/4 where f is feed velocity and N is rpm  And…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.