Determine the magnitude of the equivalent resultant force of the distributed load. Express your answer to three significant figures and include the appropriate units. Specify the location of FR on the beam measured from point A.

Q: Replace the loading by a single resultant force, specify the location of force measured from point…

A: Note that, the center of mass of a uniformly varying loading (UVL) acts at the position of two-third…

Q: It is desired to remove the spike from the timber by applying force along its horizontal axis. An…

A:

Q: Replace the loading on the frame by a single resultant force. Suppose that Fi = 250 lb , F2 = 90 lb…

A: Given data as per question F1 =250 lb F2 = 90 lb M =500 lb. ft considering horizontal forces  as…

Q: Determine the resultant R (single equivalent force) of the three forces acting on the simple truss.…

A: To Find: The resultant R of the three forces acting on the simple stress. Concept used: The net…

Q: 3) The lift force on an airplane's wing is given by the distributed load w(x)=-15(1-0.04x²) kN/m and…

A: The distributed load on the wing is given by The weight is given by

Q: A bent pipe is connected by a thrust bearing and a cable as shown. If a Force, F = 184 lb, is…

A: There will be two reactions at thrust bearing and tension in the cable. Since Force F acts in single…

Q: From the given beam, determine the moment at point B. The unit for Force is in Newton(N) and Length…

A: For different beam supports reaction loads 1. Roller : Vertical Force 2. Hinge : Vertical Force,…

Q: 200 - 400 A 200 N m D E 200 F Dimensions in mm Determine the magnitude of the force (in N) of the y-…

A:

Q: A -3 m- 9 kN/m d -6 m- FR B B

A: Area under UVL load gives load. From varignons theorem the distance d can be found where resultant…

Q: Calculate the moment (positive if counterclockwise, negative if clockwise) of the 200-N force on the…

A: Given : force = 200 N To find : moment of the 200 N force about the center of the bolt

Q: The horizontal force P is subjected on the slit open circular ring beam. Determine the horizontal…

A: Horizontal displacement at point A: - Assume any section x-x and point x on the ring. Now moment at…

Q: Determine the location of the resultant force acting on the beam from point A. Draw a free body…

A:

Q: - Replace the distributed loading with an equivalent resultant force, and specify its location on…

A:

Q: Draw the shear force and bending moment diagram for the loaded beam shown below. Also mark the…

A:

Q: 4. The Distributed load is shown in the figure. Determine; a. the magnitude of the equivalent 42 N/m…

A:

Q: Find the vectors that satisfy the stated conditions. NOTE: Enter the exact answers using the…

A:

Q: Determine the reactive forces and moments at the point O and point A 6 kN/m 15 kN 500 kN m 7.5 m 4.5…

A:

Q: Determine the magnitude and direction angles of the resultant force acting on the flag pole. FB =…

A:

Q: Determine Phe absolute maxi mm moment in the beam due to the loading below

A:

Q: 2 kN/m 2 kN/m -9 m- 5 kN/m 15 m

A:

Q: Dimensions in mm Determine the magnitude of the force (in N) of the x-component of the internal pin…

A:

Q: Given the load the diagram of the overhanging beam 900 lb 400 lb 60 lb/ft A 4 ft RA 8 ft 6 ft Rc…

A:

Q: 2/52 Determine the angle e which will maximize the moment Mo of the 50-lb force about the shaft axis…

A:

Q: Replace the loading by a single resultant force, specify the location of force measured from point…

A: The load distribution, w(x) = x­3/3 kN/m.The length of span of beam, L = 3 m.

Q: Replace the load acting on the beam with an equivalent resultant force. Specify the location at…

A: To get the equivalent resultant force we will just apply the equilibrium conditions for given…

Q: The body on the 15-degree incline is acted upon by force P inclined at 20 degrees with the…

A: Given Data Inclined plane on which body placed P force applied at angle 20' With horizontal…

Q: Find the resultant of the concurrent forces R and S for which the direction is specified by slope,…

A:

Q: 05: Find the magnitude, location and slope of the resultant of the non-concurrent coplanar force…

A: We need to sum the horizontal and vertical forces also take the moment about any point to calculate…

Q: Determine the magnitude of the equivalent resultant force of the distributed loading and specify its…

A:

Q: Suppose that w = 220 kN/m. Specify where the resultant force acts on the beam measured from A.

A:

Q: As in your role as a student in the functional physics course, you are required to determine the…

A:

Q: 400 N/m 200 N/m B 8 m

A:

Q: The block shown in the figure below is acted on by its weight, W = 1300 Lbs, a horizontal force H =…

A:

Q: 0.5 m B Example Replace the force system acting on the post by a resultant force, and specify where…

A:

Q: 1.2 m 0.4 m 0.2 m Calculate the total moment vector (all three components) that force F = 35i + 726j…

A:

Q: Determine the horizontal and vertical components of the resultant force applied to the eye bolt.…

A:

Q: The distribution of soil loading on the bottom of a building slab is shown. Replace this loading by…

A: Given Data

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.