(2) In the following Figure below, determine the gauge pressure at point A.Density of mercury = 13.6 g/cm³ = 13,593 kg/m³Density of water = 1.0 g/cm³ = 1,000 kg/m³1|Open to atmosphere, pa38cm- Mercury (13,593 kg/m³)Waterh,= 76 cmB and C are at thesame elevation

Name: (2) In the following Figure below, determine the gauge pressure at po
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: (2) In the following Figure below, determine the gauge pressure at point A.Density of mercury = 13.6 g/cm³ = 13,593 kg/m³Density of water = 1.0 g/cm³ = 1,000 kg/m³1|Open to atmosphere, pa38cm- Mercury (13,593 kg/m³)Waterh,= 76 cmB and C are at thesa

The answer is given below. Please note that as the point B and C are at same level so they are under…

Answered: determine the gauge pressure at point…

Engineering

Mechanical Engineering

determine the gauge pressure at point A.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the figure given, fluid 2 is carbon tetrachloride and fluid 1 is benzene. If patm = 101.5 kPa, determine the absolute pressure at point A. fluid 1 A T 12 cm Patm fluid 2 35 cm ] LIVE 10 nexxt Reimagine Education. www.dlsl.edu.ph
The inclined tube manometer shown in the next figure is used to measure small pressure perturbations (Ap). This manometer is composed of a large tube (diameter (D), area (A)) and a small inclined capillary tube (diameter (d), area (a)) and angle (0). Any small pressure difference will result in fluid displacement (Ah) in the large tube and a significant displacement of the fluid in the capillary at a length (AL.). Ap AL initial level Ap (1) Obtain a relationship between (Ah) and (AL) ! (hint: displaced liquid in large tube is equal to that in the small tube ) (2) What the formula for (z2 – 21) ? (hint : height between level 2 and level 1) (3) Express the pressure (Pz-P1) in terms of (AL, 0, p, g, d, and D) ? (4) At what angle should the manometer be adjusted so that (AL-5 Ah) ?
Select the correct value of H: ( The density of liquid =990 kgim, gravity g = 9.81 mis and L= 90 cm, Pressure P1= 52.369 Kpa) Air Pt Liquid (2)
Answer the following. A: When the pressure of liquid is increased from 3.5 MN/m² to 6.5 MN/m² its volume is found to decrease by (0.08) percent. What is the bulk modulus of elasticity of the liquid? B: An open cylindrical tank (1.2m) in diameter and (1.8m) deep is filled with water and rotated about its central axis at (60 r.p.m). How much liquid is spill and how deep of the water at the central axis.
Q5 A U-tube manometer similar to that shown below is used to measure the gauge pressure of water (mass density p = 1000 kg /m3). If the density of mercury is 13.6 x 103 kg /m³, what will be the gauge pressure at A if h1 = 0.45 m and D is 0.7 m above BC. Wwater Wmercury
(1) The mercury manometer in the Figure below is connected to the inlet and outlet of a water pump (the left side to the inlet and the right side to the outlet). Assuming that the inlet and outlet are at the same elevation, determine the pressure increase for the pump. - Inlet and outlet elevation Water hy =15 cm Mercury 13.93 kpin! Density of mercury = 13.6 g/cm³ = 13,593 kg/m³ Density of water = 1.0 g/cm³ = 1,000 kg/m³
A manometer using oil (density 0.900 g/cm3) as a fluid is connected to an air tank. Suddenly the pressure in the tank increases by 7.61 mmHg. Density of mercury is 13.6 g/cm3. By how much does the fluid level rise in the side of the manometer that is open to the atmosphere? ? cm
The capillary rise and fall in the glass tube used for both measuring water level and mercury level is not to exceed 0.8mm and 0.3mm respectively. Determine the minimum size of a glass tube for both liquids, given that surface tension of water = 0.082N/m and surface tension of mercury= 0.52 N/m with diagram. MODEL QUESTION PAPER
Sometimes manometer dimensions have a signifi canteffect. In Fig. containers ( a ) and ( b ) are cylindricaland conditions are such that p a = p b . Derive a formula forthe pressure difference p a - p b when the oil–water interfaceon the right rises a distance ∆ h< h , for ( a ) d << D and ( b ) d=0.15 D . What is the percentage change in the value of ∆ p ?
A gage attached to a pressurized nitrogen tank reads a gagepressure of 28 in of mercury. If atmospheric pressure is 14.4psia, what is the absolute pressure in the tank?( a ) 95 kPa, ( b ) 99 kPa, ( c ) 101 kPa, ( d ) 194 kPa,( e ) 203 kPa
Round off at the final answer only! As illustrated, the semicircular gate AB is utilized to store kerosene. In meters, how far is the center of pressure from A? Kerosene SG= 0.82 5 m 3 m A B -P Gate: Side view
Q1: An oil pipeline and a 1.3m³ rigid air tank are connected to each other by a manometer, as shown in Fig. If the tank contains 15 kg of air at 80°C, the absolute . .pressure in the pipeline Oil 1.3 m Air, 30°C SG=2.68, It= 75 cm Alt = 20 cm 3D 'D=4 mm 50° Mercury SG = 13.6