Determine the force in nember FH for the pin- connected truss shown.' F = 2000 N each F F F IF 0.8 m 0.8 m 0.8 m 0.8 m 0.8 m TA H. 2.5 m E (A) 0 (B) 2320 N (compression) (C) 3840 N (tension) (D) 4130 N (tension) B. C.

Q: list the most popular cars, what they cost, and if they are gas, electric, or hybrid cars for:…

A: The most popular 5 car models for each of the car company is provided below. Toyota: Toyota…

Q: n's Law of Motion odynamics mples (situational or not) from e

A: To give: The summary of Newton's Laws of Motion and Thermodynamics, with some examples.

Q: what are the symbols for frictional force, applied force, normal force, and gravitational force?

A: ■ The frictional force exist due to surface roughness and the relative motion between the bodies. ■…

Q: t is the figure called? explain and elaborate

A: The apparatus is a open cup flash point test apparatus

Q: would it be possible to get a detailed explanation? thank you

A:

Q: For the process shown in the schematic below, which of the statements is/are incorrect? Feed hopper…

A: 1)b. The process can only work with thermoplastics and not with thermosets due to the thermal…

Q: 1- A simple introduction. 2- The benefits of this process. 3- The disadvantages of this process. 4-…

A: The mechanical motion of a punch is used to deep draw sheet metal. Under consistent hydrostatic…

Q: A hydraulic press is used to apply 500 lbs of force to press fit an assembly. The cylinder has a 2"…

A: Given:The force applied by the hydraulic press, The diameter of the piston, The diameter of the rod,…

Q: If a car weighing 2400 lbs is able to go 1000 ft up a mountain incline whose angle of inclination is…

A: Given data: Weight of car = 2400 lbs                      Distance which car moves up the incline =…

Q: Stanum is vital as mankind enters Stone age New age Brass age Bronze age

A: Correct answer: Bronze age

Q: What do you mean by Static Process?

A: The static process can be called the process where things are unchangeable or we can say that the…

Q: Water flows from a large tank into a 6" diameter pipe through an entrance condition of a square…

A: Given:Pipe diameter, D2=6 inchRadius of the rounded inlet, r=0.12 inchFind:The head loss reduced at…

Q: How forces are transmitted?

A:

Q: Which is the "noise"?

A: We can produce sound by creating some vibration with objects.

Q: Figure A. Rectangular block of steel. Adapted from: https://media.wdscomponents.com/ri-…

A: Given: Workpiece is slimmed using slab milling To find: 4 items need to perform slab milling process

Q: Define 'power'.

A: It can simply defined as the amount of work done per unit time. Or the rate of time of doing work or…

Q: Structure and Injecting Energy

A: The concepts of "Structure" and "InjectingEnergy" These terms can have various meanings depending…

Q: What's the worst car ever made?

A: Given Data⇒ worst car Problem statement⇒ Problem says What's the worst car ever made?

Q: Describe the work done is proportional to the force applied (F ) and the distance traveled (s).

A: We know that,Work Done =Force × DisplacementW = F × s From the above equation, If…

Q: "If we push the book on the table, it stops after sometime. Why?"

A: If we push the book on the table, then the book will get some speed. but after some time the book…

Q: a) Given is a penstock with deflection and subsequent cross-section reduction. Determine the…

A: Find the pressure loss.

Q: So what are the correct answers

A: Explanation: If we consider a system that loses heat δQ at temperature T. Since, In this case the…

Q: Explain three pages of laminar flow with the drawing

A:

Q: ACCURATELY

A: We have given ACCURATELY

Q: Problem 3: A small gearing system in your brand-new 3D printer fails as you were printing, leading…

A: To prove: We must demonstrate that the equipment failed under normal operating circumstances in…

Q: Manufacuring Processes An electro chemical machining (ECM) operation is employed too cut a square…

A: Write the given data:

Q: Could you please give some details, and explain more how to get from step 1 to step2. it is not very…

A: Here for the clarity in the solution we can draw line diagram of the system: Here the movement of…

Q: A pair of forces acting directly on the material to reduce in its length are called   Select one:…

A: Solution:

Q: have you figured out part b yet?

A: To determine the magnitude of the reaction force at each bearing, we'll relate the acceleration of…

Q: a BUE? Why does it form?

A:

Q: When using a specific mass of an ideal gas with a specific pressure inversely proportional to the…

A: Ideal gas equation is given by, PV = mRT where, P = absolute pressure of gas V = volume of gas m =…

Q: Derive Equation 13.3.

A: Consider W1 is the apparent weight of the solid with the sinker submerged, and W2 is the apparent…

Q: c. In the field, the position of the interface between oil and water is often difficult to determine…

A:

Q: 6. Low carbon steel can be machined using Abrasive jet machining. 7. Tool life in EDM is infinite.…

A: Note: Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: Which of the following situations has the greatest impulse? A very large collision force acting over…

A: Impulse: The product of the applied force with the time duration of acting is known as impulse. The…

Q: 1. What are the normal use or uses of this product or component? What are the normal operating…

A: Given questions: 1. What are the normal use or uses of this product or component?    What are the…