Determine the force in each of the members located to the left of FG for the scissors roof truss shown. State whether each member is n tension or compression. 1 kN 2 kN Bo 2 m 2 kN Do E 1 kN Fo G 2 m 2 m 2 m I H K 下。 2 m J. 2 m 1 m 1m 1 m 1 m L 1m Show complete solutions and diagrams. Original work please I will upvote
Q: Determine the reactions at the supports for the beam shown in Fig. 400 kN - m 15 kN/m 6 m Ţ -4 m 160…
A:
Q: Spotify m HBO Max Dis Dibuje los diagramas de fuerza con me Video N Netflix A 20kg O H B 6m 8m 12kg…
A:
Q: Find the deflection at C for the beam as shown in Figure. EI constant. Use conjugate beam method.
A: Given Data EI = Constant Find the deflection at C using conjugate beam method.
Q: 300 mm 2012 3014 250 mm Check the requirements of TS500 for ductile design and Determine the Moment…
A: Given: h = 300 mm b = 250 mm fc = 30 MPa fy = 420 Mpa d' = 25 mm
Q: Determine the moment resisting capacity (Mr) of the given cross-section -H=500 mm- 6 Φ 20 ←B=350…
A: Solution: Stress-strain profile:
Q: It is observed experimentally that the amplitude of free vibration of a certain structure modelled…
A: Given- Number of cycles k=10, Initial stage amplitude of free vibration ui=1 Final stage amplitude…
Q: The invert elevation of a 600 mm sewer drops 0.5 m over a 100-m distance. Determine the discharge…
A: Objective: To determine the flow velocity and discharge for given flow parameters. Given: Diameter…
Q: Problem 813 Determine the moment over the support R₂ of the beam shown in Fig. P-813.
A: Given data : We are asked to determine the moment over the support R2 of the beam ?
Q: rmine the influence of pond geometry and configuration on facultative and maturation waste…
A: Using naturally occurring processes such as solar light, wind, microbes, and algae, Wastewater…
Q: 8. Energy Equation Water at the Lake William Dam enters a hydraulic turbine through a 30 cm diameter…
A: Given, inlet diameter of pipe,d1=30 cmoutlet diameter of pipe,d2=25 cmFlow rate through pipe, Q=0.6…
Q: Q3: Analyze the truss shown using substitute member method. Assume roller at joint (a) and hinge in…
A:
Q: How does house zoning cause house density in Detroit Michigan?
A: The creation of plans, as well as the control and management of towns, cities, and metropolitan…
Q: Home Work (Compound Truss) For the truss shown in figure, find the axial forces for the members…
A:
Q: 2. For the pipe flow-reducing section shown below, D₁ = 8 cm, D₂ = 5 cm, and p2 is at atmospheric…
A: Given : D1 = 8 cm and D2 = 5 cm V1 = 5 m/s h = 58 cm Determine the force resisted by the bolts ?
Q: The direct and indirect costs estimated by a contractor for bidding a project is Rs. 160000 and Rs.…
A: Given- Direct cost=160000 Indirect cost=20000 10% of bid price is mark up
Q: m 135 KN 44 kN/m t 22 kN/m 5m
A: Given Load = 135 kN UDL = 22 KN/m UVL = 44 KN/m
Q: A solid bar of uniform square cross- section of side b and length L is rigidly fixed to the supports…
A:
Q: The disinfection of water is carried out in a stirred tank. The treatment process has water as the…
A: According to given data The disinfection of water is carried out in a stirred tank. The treatment…
Q: What would be maximum possible discharge through a 2.5 m wide rectangular channel. If specific…
A: Given- Width B=2.5 m, Specific energy E=1.2 N-m/m,
Q: Can you please solve the number 2 question in the picture? Thank you
A:
Q: Horizontal highway curve: Given PI at 95 + 54.78, Δ = 24°28’, and D = 5°30’, compute the deflections…
A:
Q: A 290 kg/m light crane rail sits on and is securely fastened to a W400mmx67kg/m crane girder.The…
A: Solution:- Given data:- Vertical load (V) = 80 kNHorizontal load (H) =8 kNA = 8580 mm2d = 400 mmbf =…
Q: The bent rod is supported by a smooth surface at B and by a collar at A, which is fixed to the rod…
A: Given : F = 100 lb M = 35 lb ft To Find :
Q: 5. A compound curve, having Station PCC as 2+320, and Station PC as 2+020, has the Central Angle of…
A:
Q: (0= 25°, D1 = 20 cm, D2=1.5 cm, P1=125 kPa, and Q1=5 m³/hr) Water flows through this horizontal pipe…
A: Answer Let us first draw the free body diagram showing directions all the force Total Force…
Q: Problem 2: The above borrow pit soil has a natural bulk unit weight of 17.5 kN/m³ and water content…
A:
Q: a) The obiectives and the importance of soil exploration.
A: Soil exploration is the process of gathering soil data for the evaluation of soil qualities at a…
Q: A surveying procedure used in aligning the rod in the vertical so that the instrumentman may…
A: To explain how an instrument man determines the rod/staff is vertical. Surveying is a method of…
Q: 3. In a given simple curve, the value of the degree of curve is 5 degrees. The coefficient of…
A: Curves can be used to make a gradual change in direction or orientation in the alignment. Curves in…
Q: F6-8. 20 kN/m ↓↓↓↓ 4 m F6-8 -2 m 20 kN C
A:
Q: 1. ON THE RETAINING WALL TO THE RIGHT, DRAW THE WALL AND FOOTING REINFORCING STEEL IN THE PROPER…
A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…
Q: QUESTION 12 60 10 15-min Volumes 40 Lane Configurations Consider the left turn movement from main…
A: Potential Capacity: The potential capacity is the capacity of a roadway or a movement on a roadway…
Q: The 800-kg horizontal wall section is supported by the three vertical cables A, B, and C. What are…
A:
Q: t the instant @ = 5 rad/s, pulley A is given an angular acceleration α = (0.80) rad/s², where is…
A: The rate of change of magnitude of velocity + Rate of change of direction of motion equals the…
Q: QUESTION 1 From the given truss below, determine the forces for the members IK, IJ, and HJ. And also…
A:
Q: Solve
A: The members of truss can't generate shear force , axial force or bending moment diagrams. They only…
Q: Design beams. Where fc' = 35 Mpa, fy = 420 Mpa. and bar 25 mm. L.L = 38 kN/m 7.5 m- 500 mm Ą,=? 350…
A: As there is no specific code given so we are designing it as per Indian standard code that is IS 456…
Q: Problem 1.8. An axial pull of 35000 N is acting on a bar consisting of three lengths as shown in…
A: Here we will draw a separate free body diagram of each section.Using the formula of stress and…
Q: What is normal scour depth for a channel in soil with silt factor of unity and carrying 8 m²/sec/m…
A: Given data- Silt factor f=1, Discharge per unit width q = 8 m2/s/m, To Find- The Lacey's normal…
Q: find force in member DF,DC, ED, and EF
A:
Q: Draw the Shear and Moment Diagram. 59 kN/m 95 KN 1m 105 KN 10m 59 KN 95 kN/m 1m
A: Given loading diagram:
Q: 5m Determine The Force In Members CD And DF Of The Truss Shown. 3m 10 KN 3m 10 KN 3 m 10 KN Н 3m 10…
A: Given data in question Loads each of 10 kN Span 5 m between supports Truss To find out Forces in…
Q: A trapezoidal channel with 3.0m bottom width and 1:1 side slope carries a discharge of 10 m³/s at a…
A:
Q: Which of the following is a polymer modified binder? (a) M1000/320 (b) AMC5 (c) Class 600 (d) $15RF
A: Polymer Modified Binder: A polymer modified binder is a bitumen binder which is made up of by…
Q: Two reservoirs are connected through a homogeneous and isotropic aquifer having hydraulic…
A: Given data- Hydraulic conductivity K=25 m/day, Porosity n=0.3, Length L=2 km=2000 m, To Find- The…
Q: For the given set of forces shown, determine the following if each side of the quare is 1m in…
A: as per guidelines we need to answer only 1st three subparts of question so please repost rest…
Q: find GB
A: Given Data Find force in member GB.
Q: 11.1 Which of following factor(s) affect the ground shaking intensity during an earthquake? • The…
A: Every nation should research earthquake engineering since it can lessen the effects of earthquakes,…
Q: QUESTION 3 A plank L m long is placed in a horizontal position with its ends resting on two inclined…
A:
Q: 6. Rotating Cylinder A 40 cm diameter, 90 cm high vertical cylindrical container is partially filled…
A: Given, Diameter =40 cm Height of water (partially filled)=60cm angular speed of rotation=120 rpm to…
Trending now
This is a popular solution!
Step by step
Solved in 4 steps with 4 images
- Determine the force of the members for the space truss shown in the figure. Joints A and B are supported by ball-and-socket while Joint C is supported by short link along z-axis. Indicate whether member is tension (T) or compression (C). 2m y Sm Az By BX Bz PAR Ax CSXScanned with Ca canner a SISU KN 15m 1 2117Select all zero-force members in the truss shown below. Check the box for zero- force members 3 m 3 m 12 m, 8 @ 1.5 m DE O LK ЕР O HF O BC BM EF OM CD BN LO O DK FI O coO O O A:11 Hw3-2021.docx Name: Time you spent to solve the ID.: problem : Section HW- 3 Determine the forces in all the members, and state if these members are in tension or compression. Use table to arrange your calculations, show the results on the truss ( if not your will take zero) 30 N F II
- A tie member of a roof truss consists of 21SA 100 x 75 x 8 mm. The angles are connected by fillet weld as shown in figure on either side of a 10 mm gusset plate and the member is subjected to a factored pull of 450 kN. Take size of weld as 6 mm and connections are made in workshop. [Use Fe410 grade of steel] 75 m L. C. = 31mm 16A (100 x 75 x 8) mm Choose the nearest correct statements: L1 = 390.5 mm L1 = 195.25 mm Correct Option L2 = 87.75 mm Correct Option L2 = 175.5 mmThe truss below is pin connected at A and E, and is acted on by the forces shown. E A D B Identify all of the ZERO-FORCE MEMBERS by checking the boxes below (if there are none, leave all boxes unchecked): BF AF BC BH CD EG -GH AB CH DG DH DE -FH7 7a 7b 7c Alaterally supported beam was designed for flexure. The beam is safe for shear & deflection. The most economical section is structural tubing however the said section is not readily available at the time of the construction. If you are the engineer in charge of the construction what alternative section will be the best replacement? Why? The section is 8" x 8" x 7.94 mm thick: Use Fy=248 MPa: E=200,000 MPa AISC wall thickness Ix 106 S x 103 Jx 103 mm4 mm3 mm4 rx =ry Area Ag (mm2) mm Designation Weight/m 8x8 7.94 47.36 6,039 79.25 37.84 371.99 60.35 expla'n briefly your cho'ce. (transform your comparative analys's 'nto a narative form to support your cho'ce) 8x8 14.29 80.61 10,258 76.2 59.52 585.02 99.06 8x8 72.7 9,290 76.96 54.53 539.13 90.32 8x8 9.53 56.09 7,161 78.48 44.12 432.62 70.76 mm 12.7 Zx 103 mm3 437.53 714.48 650.57 512.92
- Steel Designa. Say a W12x45 is not safe against rupture, what other design considerations should be explored to increase its capacity and thereby be safe for rupture.b. Say you are to design a tension member using a C-section and found out that no C-section is safe against yielding and rupture. As a designer, what would be your approach to this? Ans. is built up section, please do explain why build up section.Consider the truss shown in (Egure 1). Suppose that F-60 kN and F₂-25 kN Figure 40 KN Part C Fau 50 AN Submit -2m- D 15m 1of1 > 15m 15m μA Value -F₂ Part A Request Answer Determine the force in member ED of the truss, and state if the member is in tension or compression Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. HA FED Value Submit Part B Request A Determine the force in member EH of the truss, and state if the member is in tension or compression Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Submit Fon- Value Determine the force in member GH of the truss, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of…3) Determine the Force in each member of the truss shown in the Figure. (Use the Method of Joints.) D B gl 12' H E 300lb 300lb goolb 9' 9'
- Determine the complete set of zero force members in the given N-type truss subjected to concentrated loads at joints. 10 kN 5 kN 5 kN 10 kN 5 kN -5 kN T 5@2 m = 10 m A FG and BK B AB and FG C FG and AL None of the above option is correct Your answer is CorrectQ4\ Which of the following is a zero-force member? 3 8KN 4 G 4 エ 子c D. 4 B AC BD IF IDQuestion # 1: Determine the force in each member of the truss and state if the members are in tension or compression. 300 lb 600 15 B 60015 GOO G 11. 244in. 6 ft load at point B, D, F = 600 lb load at pount A and H=300 lb distance AC = CE =EG = GH = 8FT -80---SA- [Answer: FAB=15001b-C. Fac-12001b-T, Fac0, For-12001b-T, Fan+ 12001b-C, F₁-601b-C. Form 721h-T, Use symmetry to obtain the rest of the members]