Determine the flow rate in Its/s and in p^3/s that circulates through the Venturi meter. The height H (in meters) and the gauge pressure at point P (in Psi) lbs/in^2. Note: All information appears in the figure. домст 2₂=10cm AH:150mm = 13.57 1020

Q: Determine the equation of the influence line for the reaction at A in the continuous beam shown in…

A: By Muller Breslau method, As we have to find the reaction at end A, hence Support at A will be…

Q: What is this called?

A: Chisel

Q: Determine the Centroid of 3 Areas.

A:

Q: Sketch SFD and BMD in terms of w and P

A:

Q: 5. Find diameter y. All dimensions are in millimeters. 1 + 19.30 DIA 118.00 -३०

A: Tapered beam with larger diameter at AB = 19.3 mm  Length of beam ,L = 118 mm  Tapered angle = 3°…

Q: F & H are incorrect

A: As per question requirment we only find out f and h here. Find out -  (f) Length of Curve (h)…

Q: Quiz #1 Problem 1: Prove the following relationship. Gs Y. (1+ Mc) Y =- 1+e

A:

Q: Determine the ỹ coordinate. y b. = ky? a

A:

Q: Fo B - P 800 mm C -600 mm

A:

Q: 7⁄8 inch+  5⁄32 inch

A:

Q: Find KN derivation Y = K m²³

A: We have to prove that the unit of unit weight is kN/m3.

Q: Describe briefly the T-v Diagram.

A: The TV diagram refers to the Temperature-Volume diagram for a particular substance. The diagram…

Q: Determine y for the area shown y 1" 1" in .5" 1" 2" 2" X

A:

Q: 1⁄6 yard +3⁄8 yard

A:

Q: According to this figure, What is d? What is dt?

A: Draw the figure.

Q: what are the USCS group name for each of the four gradations

A: Given: Specimen LL PL PI Cc Cu 1 53 24 29     2       1.05 95.52 3 27 16 11 3.06 28.34 4…

Q: Determine degree of total indeterminacy

A: Given data : The given structure is truss structure . It is pin connected carrying tension or…

Q: 05 Find the XT 0.5 1.5 3 2.5

A:

Q: 31⁄5 / 4⁄7

A: 31/5=6.2 4/7=0.571

Q: hat about pin d?

A: We know that Forces acting at Joint D are shown in figure below Forces moving away from joints are…

Q: For the following items, answer whether the multiview projection matches the isometric drawing depic…

A: The given figure shows the different items, it is required to state whether the Multiview projection…

Q: 65 degree 6' - 17 degree 54'

A: 1 degree = 60' 65 degree 6' = 64 degree 66'

Q: PROBLEM 2: Determine Ix and Tx.

A: given- a plane figure to find- M.O.I  about X-axis and centroidal axis.

Q: 205, 406 ton=722 %3D How are Yoll tonne - 72 %31

A: Give that, Tonne is metric measure  1 TON  = 0.90718 tonne   TON is American unit

Q: [Choose ] solve equilibrium equations simultaneously ensure you have an equal number of unknowns and…

A: Understand force flow. Understand the math behind structural analysis (concepts like virtual work…

Q: Difference betwen Veletile nd frzcead Saled

A:

Q: 38 O 18 22 66 102 The known: front projection, side projection Required: Draw the three projections…

A:

Q: The column section shown above is reinforced with equal number of 20 mm bars с 1. on each face.…

A: Answer  1) Calculation of neutral axis 'c' We know that at balanced condition strain at extreme…

Q: Determine centroidal coordinates of the volume.

A: x¯=∑χiVi∑Vi   =610×660×6102 + 12×610×660×(610+13×610)610×660 + 12×610×660   = 474.45 mm y¯=8132    =…

Q: where did 3sqrt of 2 came from?

A: Given, A structure with carrying varying load   To find : Where 32 came from.

Q: 4 cm 0 2 י 5 cm 4 567 Value: cm 10 5 150 Value: mm 0 140

A: There are two scales, and the values shown on the two scales are required.One is the main scale and…

Q: The block of mass m1 = m0 is attached to a spring of elastic constant k = (m0g)/H and natural length…

A:

Q: * .I don't like this," said Ali“ Correct Incorrect

A: The correct punctuation marks for this be like this "I don't like this," said Ali.

Q: Define phreatic surface.

A: The term phreatic is used in hydrology and the earth sciences to refer to matters relating to ground…

Q: A Derive the equation for the unit influence line for the reaction at the support B in the…

A: By Muller Breslau method, remove Reaction at support B and place a Load of P as shown in figure. By…

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.