Determine the discharge of the river. Slope of water surface = 0.80%, Roughness coefficient (n) = 0.030 Select the correct response: 32.36 cu.m./sec. 34.645 cu.m./sec. 28.56 cu.m./sec 24.67 cu.m./sec.

Determine the discharge of the river. Slope of water surface = 0.80%, Roughness coefficient (n) = 0.030 Select the correct response: 32.36 cu.m./sec. 34.645 cu.m./sec. 28.56 cu.m./sec 24.67 cu.m./sec.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: H.W a -A 3 hours storm produces a flood hydrograph as: t (hr) Q (m²/s) |0 3 6 9 | 4 9 12 18 | 12 15…

Q: Q:When B1/z=0.5 & B2/Z=0.25, so 15? find I=? TABLE 8.8 Influence Factor I, by Equation (8.11) (Half…

Q: 05. You have the ½h-UH due to 1 cm effective rainfall. Time (hours) ¼h - UH (m/s) 0.5 60 1.0 150 1.5…

Q: A flood occurs in a main channel having a trapezoidal section (side slope on both sides: 2H to 1V)…

Q: Calculate values of the followings: y, B and v in the channel.

Q: ute the Darcy velocity and seepage velocity for wa olumn with the following characteristics: K =…

Q: A trapezoidal concrete-lined ditch has a bottom width of 3 depth of 2 ft, and side slopes of 2:1.…

A: Assuming Manning's coefficient (n)= 0.015 for concrete lined channel Bottom width (B)= 3ft Depth of…

Q: Q4. (a) What do you mean by abstraction from precipitation? Which part of it is known as productive…

Q: Question-A The channel index at irrigation outlet is 5/3. Find the value of setting for an orifice…

A: Given data- Channel Index = 5/3Orifice type outletTo Find-The value of setting

Q: Q27 : A rectangular sedimentation tank use to treat 1.5 ML/d of raw water. Assume the detention time…

Q: Using the data in the table below and the rain gauge distribution shown in the figure below,…

A: Data given Find average rainfall using Theissen polygon Method

Q: The following statements are not true except The channel slope or slope of the channel bed has a…

A: Here the correct option is '5th'. None of the above. Because the option 1,2,3 are true.

Q: QUESTION 1: Vector F=2.15 kN and vector F2=2.46 kN. Determine the resultant of these two vectors.…

A: Find resultant of given forces from problem 1 and 2 (Note;Answers given of problem 1 are wrong,i…

Q: L F. Given the following 6-hr Unit hydrograph. Astorm had three Successive 6 hr intervals of…

Q: time of concentration for

A: Using manning equation

Q: The following information are given: Mud density= 10 ppg, depth=D11000 ft., It is required to use…

A: The given data is shown below: Mud density=10 ppgDepth=11000 ftHydrostatic pressure=450 psiWater…

Q: Q7: A discharge of 0.15 cumecs is supplied into a canal at the head and 0.1 cumecs is delivered to…

A: From the given date it is required to find the various types of irrigation efficiencies like…

Q: 3- Determine the discharge rate in a 1.52m diameter Corrugated metal Pipe (n= 0·024) on a slope of…

A: Given data: Diameter (d)=1.52 m n=0.024 Slope (S)=0.005

Q: What is the depth (in meters) of a circular sedimentaion basin for a design flowrate of 3800 m/d…

A: Design flow rate, Q = 3800 m3/day = 3800/24 = 158.3333333 m3/hr Detention Time = 3 hrs Therefore,…

Q: 12. Given the following data for a stream of uniform flow: 15pts A = 6.97 sq.m. P = 9.76 m S=0.007…

Q: Sandstone reservoir rock that has porosity 19% and flow zone indicator 0.0247 um.Calculate the…

A: Given- ϕ=19%FZI=0.0247μmValue of permeability for sandstone=10-10m/s

Q: Which of the following statements are true about the Hazen Williams (HW) Equation. Select all that…

A: This question is related to the Fluid Mechanics from Civil Engineering. In this question we choose…

Q: Design the salient dimensions of a syphon well drop for the following particulars: Fall = 3.8 m…

Q: Q (5-7)/ Water flows uniformly in an earth rectangular cross section open channel. Data available…

Q: n TABLE Q2(b): ) Convert the rainfall depth into cumulative raint ) Develop the rainfall intensity…

A: Mass curve is plot between cumulative rainfall depth on y axis and time on x axis Hydrograph is plot…

Q: Determine and draw the baseflow using; a. Straight line method b. Fixed based method using N = 5 С.…

A: Baseflow separation from hydrograph can be done using three methods. They are 1. Straight line…

Q: accepted to 10 % then the eturn period for design should be? (b) 1-(0.9)0.10 (d) 1/(1+0.90.10) 0.10…

Q: 1. as illustrated below: atm H P Consider a cylindrical vessel filled with sand and water at…

A: The volumetric rate at different levels in the packed bed is calculated using the given data as per…

Q: Determine the diameter of pipe drains that drain out 24 mishara of drainage area with drainage…

A: Given information in question Roughness coefficient Drainage coefficient Gradient

Q: 1. If the flow out is 200 mm³/sec in figure 1, find K1 and K2 dh = 0.01 mm/sec, dt 2. In figure 2,…

Q: 4. GNEH: watER 250 2m 44m SUめMERCED RECTAN GULAR SURPAOE OF WIDTH W = : (m

Q: Estimate the head over a Cipolleti weir of base width 0.90 m required to pass a discharge of 600…

Q: A channel has been designed to convey clear water to a fish hatchery. The design calls for aflow…

A: The objective of the question is to determine if the existing design of the channel is adequate to…

Q: I need help on this problem Manning equation problem for parts a, especially rearranging the…

A: R (hydraulic radius) = A(area)/P(perimeter) = 250*20/(250 + 2*20) = 17.24 Q = 25000 ft3/s Q = 1/n x…

Q: 2) Determine time of concentration, tc, for use in the Rational Method for a drainage basin having a…

A: Average Grass Overland flow length, L = 80’ Slope, S = 2.5% Shallow Conc. L = 450’ S = 4.8%…

Q: ممكن حل سؤالين Find solution

A: #2Given: Side slope = 60°Depth (h) = 250 mm = 0.25 mDischarge (Q) = 0.04 m3/sc = 50 Find : Slope of…

Q: Drainage areas and entry times are given. Find the flow rate at point 3 in the rainfall area in the…

A: Drainage Area: A waste bowl is any space of land where precipitation gathers and depletes off into a…

Q: Design a sedimentation tank to be treat 0.10 m³/sec

A: The design of a sedimentation tank involves determining the dimensions and other parameters to…

Q: . Assuming the criterion for suspended load transport is u-/v> 0.40 and for bed load transport is…

A: Objective: To determine the settling velocity. Given: Kinematic viscosity () = 1.186×10-4 m2/s…

Concept explainers

Time and time related variables in engineering

Time is the event progression starting from past to present and then, future statistically. The time-related variable is any particular value in relation to time to assess its changes on a specified (XY) plane.

Question

Determine the discharge of the river. Slope of water surface = 0.80%, Roughness coefficient (n) = 0.030
Select the correct response:
32.36 cu.m./sec.
34.645 cu.m./sec.
28.56 cu.m./sec
24.67 cu.m./sec.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Time and time related variables in engineering

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

pesign a rectangular sedimentation tank to treat 120000 m3/day flows. ssume the SOR=30 m/day, L= 32 m, LW-4:1. D.T-3hr?
QU/ Incritical flow if z=2 and n=0.03 find Q?
A test setup is shown. A cylindrical mold of 4 inches in diameter is filled to a height H1 = 0.2 ft., with silt whose coefficient of permeability K1 = 3.8 x 10 3 ft/min. A second coaxial mold is placed on the top of the first mold whose inside diameter is d = 1.5 inches and whose %3D height is 0.30 ft. Its Thickness is negligible. The inside of this second mold is filled with the same silt, but the annular ring outside the small tube and the outer tube is filled with sand whose coefficient of permeability is K2 = 7.5 x 104 ft/min. The test set up is a permeability of constant head. Water is placed in the mold and maintained at a level h = 1.5 ft. above the level of the outlet. It maybe considered that altogether, the system consists of a fictitious soil of thickness H= H1 + H2 = 0.5 and the coefficient of permeability Kr. Find the volume of water which percolate after 30 min in cubic ft.
A rectangular channel of width 500 mm and a uniform flow depth of 250 mm has a discharge of 0.1 m/s. The value of C of adjustable bottom slope is 55. Calculate theslope ofthe channel and the convenience of fume.
Please write legibly, complete solutions, avoid rounding off intermediate values, thanks.
C11 3 sig. figures pls:)
A rectangular settling tank without mechanical èquipment is to treat 1MLD of raw water. . t = = 2.5 hr. V= 8 cm/min Depth of water + Sediment = 4.5 m Find length tank, the width of tank. If an allowance of 1.5 m is to be made for sediment, overflow rate of the tank.
O. No. 3 A right angled triangular notch was to measure a discharge of 0.28 m3/s from a rectangular reservoir. It was found to have an error (dHị to be R mm in ncasuring hcad of notch. Determine the percenlage error in discharge as dQ/Q. Take Cd - 0.6 R=100 solve with R=100
An irrigation canal is to be designed for a discharge of 40m³/s with ground slope of 1.5×10. The bed material has a size of 2mm. Calculate the dimensions of the canal. What would be the dimensions of this canal if it was to be designed on the basis of Kennedy method with C.V.R equal to 0.85. Bazin coefficient 1.5 and the ratio of bed to depth of the canal is the same as obtained above.
Civil Q- An irrigation canal has been designed to have R = 2.5 m and S = 1.6 x 104. The sediment on the bed has a median size of 0.30 mm.Determine the amount of bed load using Einstein's method.Assume depth of flow and mean velocity of flow to be 2.8 m and 0.95 m/s, respectively.
Determine the diameter of pipe drains that drain out 24 mishara of drainage area with drainage coefficient of 1.5 cm / day. The drain grade is 0.004. Manning's n = 0.013. Use Chezy's Formula.