Determine the current through the 50 load resistor in the circuit shown below.Battery 2r11 OhmV1Battery 1A) 1.0811 AB 1.0865 A1.0799 AD) 1.0769 A믐12Vr2www0.5 OhmV2믐5V•R35 Ohms

we will use kirchoffs law here =0 KVL ∑V = 0 (sum of all voltage in a loop iz zero)

Determine the current through the 50 load resistor in the circuit shown below. Battery 2 Battery 1 A 1.0811 A B 1.0865 A 1,0799 A D 1.0769 A r1 1 Ohm V1 www 믐 12 V r2 0.5 Ohm V2 ㅓ미미 5V •R3 5 Ohms

Determine the current through the 50 load resistor in the circuit shown below. Battery 2 Battery 1 A 1.0811 A B 1.0865 A 1,0799 A D 1.0769 A r1 1 Ohm V1 www 믐 12 V r2 0.5 Ohm V2 ㅓ미미 5V •R3 5 Ohms

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter10: Direct-current Circuits

Section: Chapter Questions

Problem 3CQ: Show that the power dissipated by the load resistor is maximum when the resistance of the load...

See similar textbooks

Similar questions

(a) F ind the voltage drop in an extension cord having a 0.0600-O resistance and through which 5.00 A is flowing. (b) A cheaper cord utilizes thinner wire and has a resistance of 0.300 O. What is the voltage drop in it when 5.00 A flows? (c) Why is the voltage to whatever appliance is being used reduced by this amount? What is the effect on the appliance?
A 240-kV power transmission line carrying 5.00x102. A is hung from grounded metal towers by ceramic insulators, each having a 1.00x 109- resistance. Figure 21.51. (a) What is the resistance to ground of 100 of these insulators? (b) Calculate the power dissipated by 100 of them, (c) What fraction of the power carried by the line is this? Explicitly show how you follow the steps in the Problem-Solving Strategies for Series and Parallel Resistors.
Consider the circuit shown in Figure P28.21 on page 860. (a) Find the voltage across the 3.00-0 resistor, (b) Find the current in the 3.00-12 resistor.
Integrated Concepts A 12.0-V emf automobile battery has a terminal voltage of 16.0 V when being charged by a current of 10.0 A. (a) What is the battery’s internal resistance? (b) What power is dissipated inside the battery? (c) At what rate (in °C/min ) will its temperature increase if its mass is 20.0 kg and it has a specific heat of 0.300 kcal/kg. °C, assuming no heat escapes?
The label on a battery-powered radio recommends the use of a rechargeable nickel-cadmium cell (nicads), although it has a 1.25-V emf, whereas an alkaline cell has a 1.58-V emf. The radio has a 3.20 resistance.(a) Draw a circuit diagram of the radio and its battery. Now, calculate the power delivered to the radio (b) when using a nicad cells, each having an internal resistance of 0.0400 , and (c) when using an alkaline cell, having an internal resistance of 0.200 . (d) Does this differenceseem significant, considering that the radio's effective resistance is lowered when its volume is aimed up?
Review. When a straight wire is warmed, its resistance is given by R = R0,[1 + a(T T0)] according to Equation 27.20, where a is the temperature coefficient of resistivity. This expression needs to be modified if we include the change in dimensions of the wire due to thermal expansion. For a copper wire of radius 0.100 0 mm and length 2.000 m, find its resistance at 100.0C, including the effects of both thermal expansion and temperature variation of resistivity. Assume the coefficients are known to four significant figures.
A person with body resistance between his hands of 1.00 k accidentally grasps the terminals of a 20.0-kV power supply. (Do NOT do this!) (a) Draw a circuit diagram to represent the situation. (b) If the internal resistance of the power supply is 2000 , what is the current through his body? (c) What is the power dissipated in his body? (d) If the power supply is to be made safe by increasing its internal resistance, what should the internal resistance be for the maximum current in this situation to be 1.00 mA or less? (e) Will this modification compromise the effectiveness of the power supply for driving low-re si stance devices? Explain your reasoning,
The power dissipated in a resistor is given by P = V2/R, which means power decreases if resistance increases. Yet this power is also given by P = I2R, which means power increases if resistance increases. Explain why there is no contradiction here.
An automobile starter motor has an equivalent resistance of 0.0500 and is supplied by a 12.0-V battery with a 0.0100- internal resistance, (a) What is the current to the motor? (b) What voltage is applied to it? (c) What power is supplied to the motor? (d) Repeat these calculations for when the battery connections are corroded and add 0.0900 to the circuit. (Significant problems are caused by even small amounts of unwanted resistance in low-voltage, high-current applications.)
When a straight wire is heated, its resistance changes according to the equation R = R0 [1 + (T T0)] (Eq. 17.7), where is the temperature coefficient of resistivity. (a) Show that a more precise result, which includes the length and area of a wire change when it is heated, is R=R0[1+(TT0)][1+(TT0)][1+2(TT0)] where is the coefficient of linear expansion. (See Topic 10.) (b) Compare the two results for a 2.00-m-long copper wire of radius 0.100 mm, starting at 20.0C and heated to 100.0C.
When resistors with different resistances are connected in parallel, which of the following must be the same for each resistor? Choose all correct answers, (a) potential difference (b) current (c) power delivered (d) charge entering each resistor in a given time interval (e) none of those answers
When a straight wire is heated, its resistance changes according to the equation R = R0 [1 + (T T0)] (Eq. 17.7), where is the temperature coefficient of resistivity. (a) Show that a more precise result, which includes the length and area of a wire change when it is heated, is R=R0[1+(TT0)][1+(TT0)][1+2(TT0)] where is the coefficient of linear expansion. (See Topic 10.) (b) Compare the two results for a 2.00-m-long copper wire of radius 0.100 mm, starting at 20.0C and heated to 100.0C.