For Problems 2.42 to 2.44, determine the cracking moments for the sections shown if f'c = 28 MPa and the modulus of ruptureis fr = 0.7√f'c with f'c in MPa. determine the cracking moments forthe sections shown if f = 28 MPa and the modulus of ruptureis f = 0.7√f with f in MPa.Problem 2.43 (Ans. 46.30 kN-m)2 #25300 mm420 mm500 mm80 mm

Given:- fc'=28 MPaModulus of rupture=0.7fc'Total depth of section=500 mmWidth of section=300 mm To…

Answered: determine the cracking moments for the…

determine the cracking moments for the sections shown if f'c = 28 MPa and the modulus of ruptureis fr = 0.7√f'c with f'c in MPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Two uniform wooden members with the cross-section of 30mm x 20mm have been glued by the splice shown…

Q: a) Transform the beam into one made entirely of steel. b) The steel channel is used to reinforce…

A: Given Data The maximum moment (M) = 1.2 KN-m Est = 200 GPa Ew = 12 GPa We are asked to evaluate the…

Q: The compound shaft shown consists of aluminum segment (1) and steel segment (2). Aluminum segment…

Q: A punch of 20 mm diameter is used to punch a hole in 8 mm thick plate. If the force required to…

A: Given data- Diameter of the punch = 20 mm, thickness = 8 mm, force = 110 kN, To Find- The value of…

Q: The compound shaft shown consists of aluminum segment (1) and steel segment (2). Aluminum segment…

Q: 2. Determine the cracking moments for the sections show 6 in. . -18 in-

Q: A threaded steel rod (Es = 210 GPa, dr = 12 mm, as = 12 x 10-6/°C) is held stress free between rigid…

A: Given, Es=210 GPadr=12 mm4αs=12×10-6/°Cdp=15 mτ=45 MPaσ=70MPa

Q: Please analyse question 3C(i) with a M1 = 35kN.m as an un-cracked section and 3C(ii) with a M2 =…

A: Given data Es = 200 GPA Ec = 30 GPA b = 300 mm h = 520 mm d = 460 mm m = 6.67 As = 1470 mm2

Q: The compound shaft shown consists of aluminum segment (1) and steel segment (2). Aluminum segment…

Q: Using the cracked transformed section with b = 250 mm and d= 500 mm and j= 0.8501, If M = 150 KN.m…

A: Given :- Width of the transformed section (b) = 250 mm Depth of the section (d) = 500 mm j= 0.8501…

Q: Problem #1. The figure below are 2 solid cylindrical bars joined together at point B. Find the…

Q: total length of column member, I = 3 m beam width, b = 6" or 150 mm (dressed) beam depth, d = 6" or…

A: Total length of column(L)=3 m Total load(P)=56.25 kN Width of column(b)=6" or 150 mm Depth of…

Q: The radius of a Mohr's circle for stresses at a point in a body to o = -160N/mm², 6, = 350N/mm², T,…

A: Given : σx = - 160 N/mm2 σy = 350 N/mm2 τxy = 0 This is a problem of Strength of materials where we…

Q: Determine the reaction at the roller at C of the beam shown below. Take EI= constant. Use the Method…

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

Q: 50mm (for BC), find the average normal stress in each road and the total deformation of road AB and…

Q: cracking moment

A: To find the cracking moment of the given section where the concrete strength is 28 MPa

Q: Determine the maximum thickness (t) of the specimen if it is subjected to a force P = 5 KN. The bar…

A: Consider below figure ; At A ; σ = PA 100 = 5 × 100037.5 t t = 1.333 mm --------- 1

Q: The compound shaft shown consists of aluminum segment (1) and steel segment (2). Aluminum segment…

A: Outer diameter of aluminum shaft, Wall thickness of aluminum shaft, Outer diameter of steel shaft,…

Q: Problem Two: Consider the cross-sectional shown in the figure below. The cross-section is reinforced…

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

A: to find - absolute maximum shear stress from given principal stresses.

Q: Q1 : For the rectangular beam shown in fig. find the following : fy =420 MPa f. = 25 MPa . 1-…

A: Solution:- We know that bending equation, MI=σy=ER Moment of inertia of section, I=B×D312 =…

Q: Question 4 At a point in a thin steel plate in plane stress (0z = Txz= Tyz= 0), Ex=600, &y= - 2004µ…

A: E=2G1+ν=276.921+0.3=200Gpa

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

A: Given data, u = 1.5 mmv = 4.3 mmc = 710 mmα = 32° β = 58°To find out the shear strain γ at corner Q′…

Q: The compound shaft shown consists of aluminum segment (1) and steel segment (2). Aluminum segment…

Q: Determine the cracking moment in kN-m for the section shown if: f'c = 28MPa

Q: A thin walled rotating shaft is subjected to a torque and a bending load. The torque produces the…

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

A: This question is related to the Strength of Material.

Q: An Assembly shown below whereas a link BD consists of a bar with 1 in. wide and 1/2 in. thick.…

A: make free body diagram Use moment equation find reaction

Q: fr= 7.5 vf'c Determine the cracking moments for the section shown if fc=4000psi Convert dimensions…

A: Given : fc = 4000 psi Modulus of rupture, fr = 7.5f'cfr = 7.5×4000fr =…

Q: 2. For each of the plane stress states listed below find the three principle stresses and the…

A: Given data:- a) σx=20 kpsi, σy=-15 kpsi, τxy=8 kpsi cw b)σx=16 kpsi, σy=10 kpsi, τxy=5 kpsi cww c)…

Q: The point loads are placed at the fixed positions shown in the figure and they are live loads. A K a…

A: Since the condition for each subpart is varying, the first part will be calculated. Please submit…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

Q: The bar shown made from steel (Sut = 140 ksi) is subjected to a fully reversed bending moment of…

A: As math type is not available, providing hand written solution

Q: -gment (1) is a tube with an outside diameter of D- ear modulus of G₁ = 4,000 ksi. Steel segment (2)…

Q: 2.22 Given o xx = 20 MPa, o y = -10 MPa, and oxy =-20 MPa, find the principal stresses and principal…

Q: Calculate the internal torques T₁ and T₂ in shaft segments (1) and (2), respectively. On paper,…

A: Determine the internal torque of shaft 1 and 2 and draw internal torque diagram.

Q: = The compound shaft shown consists of aluminum segment (1) and steel segment (2). Aluminum segment…

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

A: Given data, E = 190 GPa a = 50 mm b = 140 mm c = 70 mm To find out the flexural stress at the top…

Q: Q5) The wooden block shown in Figure (4) will fail if the shear stress acting along the grain is…

A: In the given plane only stresses acting along X and Y direction and no shear stress (Txy =0) is…

Concept explainers

Crack Detection

Concrete materials are meant for supporting structures, building foundations and they act as several load-bearing structures. Over time, due to environmental conditions, and based on the constituent materials used, concrete materials are subjected to a great degree of distress. Corrosion of the reinforcement bars due to chemical influences, uneven base, earthquake, drying shrinkages, and alkali-aggregate reactions are some of the reasons for concrete distress.

Question

For Problems 2.42 to 2.44, determine the cracking moments for the sections shown if f'c = 28 MPa and the modulus of ruptureis fr = 0.7√f'c with f'c in MPa.

determine the cracking moments for
the sections shown if f = 28 MPa and the modulus of rupture
is f = 0.7√f with f in MPa.
Problem 2.43 (Ans. 46.30 kN-m)
2 #25
300 mm
420 mm
500 mm
80 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Problem #2 (5 points): Fig. 2 shows aluminum hollow rods (outer diameter is 2 in. and inner diameter is 1.5 in.) that are fixed to rigid walls. The gap between the rods is 0.005 in when the temperature is 60°E. If the temperature is 200°F, what is the stress in each rod? aai = 13 x 10/F, Eai = 12 x 10 ksi %3D 0.005 in. .8 in. Fig. 2 Page | 1
The compound shaft shown consists of aluminum segment (1) and steel segment (2). Aluminum segment (1) is a tube with an outside diameter of D₁ = 4.15 in., a wall thickness of t₁ = 0.25 in., and a shear modulus of G₁ = 4,000 ksi. Steel segment (2) is a tube with an outside diameter of D₂ = 2.00 in., a wall thickness of t₂ = 0.125 in., and a shear modulus of G₂ = 12,000 ksi. The compound shaft is subjected to torques applied at B and C as shown. Determine the rotation angle of C with respect to the support at A. (1) 9 ft -0.0343 rad -0.0429 rad -0.0259 rad -0.0320 rad O-0.0460 rad 1,700 lb-ft B (2) 6 ft 650 lb-ft
Determine the absolute maximum shear stress for each of the following plane stress states for which the principal stresses are given. (a) op1 = 2320 psi, op2 = -1590 psi, op3 = 0 (b) op1 = 47 MPa, Op2 = 27 MPa, Op3 = 0 %3D Answer: (a) Tabs max psi MPa (b) Tabs max
A circular aluminum alloy [E = 70 GPa; a = 22.5 × 10-6/°C; v = 0.33] pipe has an outside diameter of 215 mm, a wall thickness of 12 mm, and a length of 4.3 m. The pipe supports a compressive load of 695 kN. After the temperature of the pipe drops 43°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) ō = i AD = i mm mm
please box the final answer
Reinforced concrete
Due to loading, the plate is deformed into the dashed shape shown in the figure. Assume a = 39 in., b= 33 in., δ1= 0.1625 in., δ2= 0.1 in. Determine the average normal strain along the side AB?in micro rad And answer in right and clear way Determine the average shear strain in the plate at A relative to the horizontal and vertical axes?
Reinforced concrete
Determine the absolute maximum shear stress for each of the following plane stress states for which the principal stresses are given. (a) Op1 = 2780 psi, Op2 = -2440 psi, op3 = 0 (b) op1 = 58 MPa, op2 = 35 MPa, Op3 = 0 Answer: (a) Tabs max= psi (b) Tabs max = MPa
50% Due to loading, the plate is deformed into the dashed shape shown in the figure. Assume a = 32 in., b= 40 in., δ1= 0.225 in., δ2= 0.075 in. Determine the average normal strain along the side AB? Determine the average shear strain in the plate at A relative to the horizontal and vertical axes?
Cracking moment.
Determine the absolute maximum shear stress for each of the following plane stress states for which the principal stresses are given. (a) Op1 = 3300 psi, Op2 = -1830 psi, Op3 = 0 (b) 0p1 = 44 MPa, Op2 = 29 MPa, Op3 = 0 Answer: (a) Tabs max psi (b) Tabs max= MPa