Determine the clearance for the shell and tube heat exchanger with 220 tubes of outside diameter 20 mm, triangular pitch arrangement and one tube side pass. Bundle Diameter is 422.9 mm and Shell inside diameter is 437,9 mm.

Determine the clearance for the shell and tube heat exchanger with 220 tubes of outside diameter 20 mm, triangular pitch arrangement and one tube side pass. Bundle Diameter is 422.9 mm and Shell inside diameter is 437,9 mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Concentric tube heat exchanger (tubular or tube in tube) is used for a large industrial gas turbine.…

A: Given :- Concentric tube heat exchanger (tubular or tube in tube) is used for a large industrial gas…

Q: Concentric Tube Heat Exchanger How would corrosion or fouling in the pipe influence the results of…

A: Fouling stands in specialized applications, for the undesirable development or arrangement of…

Q: e inner and outer surfaces are estimated to be o.0004 and o.0002 m2 . K/W, respectively. Fouling R,…

Q: at a pressure = 2at m and flow rate = 1020 kg /min, the temp erature of hot water is being decreared…

A: To obtain the value of NTU, we must first calculate the effectiveness of the heat exchanger and then…

Q: Design Heat Exchanger Sell side Water Fluid condition Component Flow rate (kg/hr) Temperature in(°C)…

A: Given For shell side Temperature, T1 = 25oC T2 =…

Q: Calculate required exchange surfaces: for a cocurrent 1-1 type exchanger for a countercurrent 1-1…

A: To find: The heat exchange surface. Given: The mass flow rate of oil is mo˙=130000 kg/h. The mass…

Q: The diameter of the tube is 25 mm. The specific heat of water is 4.18 kJ/kg.°C. The overall heat…

A: There is a coma in mass flow rate data instead of point. I am considering it as 1.8 kg/s. If it is…

Q: Illustrate example of heat exchanger with baffle. Explain the role of the baffles in a…

A: Heat exchangers are defined as the energy conversion devices that involve heat exchange among two…

Q: a. What is shown in the figure? Where is it used and how does it work? b. What is the nature of heat…

A: a. The figure shown is heat exchangers. Typical application of heat exchangers is to use heat…

Q: List the important factors to be considered when selecting a heat exchanger.

Q: For a 50 m2 tubular heat exchanger operating under the following conditions: Heat Capacity C,…

A: We are suppose to solve only 3 subparts. Please post other parts as a separate question.

Q: WILEY 10.75 PLUS A heat exchanger consists of a closed system with a series of parallel tubes…

A: Given data: d=2 cmL=10 mTAvg=40°CV=8 m/s Need to determine the power required to operate the pump.

Q: A 3/4-in.,20-BWG ( thickness =0.035 in.) standard condenser tube is subjected to an axial load of…

Q: A simple heat exchanger is made by installing a close return bend on two 3/4-in Schedule 40 steel…

A: Given data as per the question Diameter of pipe =0.75 in =0.0625 ft Flow rate =29.2 gal/min we know…

Q: A one-shell, two-tube pass shell and tube heat exchanger has 1580 tubes with di = 13 mm and do = 16…

Q: A (fluid 1) at the rate of 145 Ib/min is heated 75 °F to 150 °F by another fluid (fluid 2) enters…

Q: What are the main classifications of the heat exchangers?

A: Given data What are the main classifications of the heat exchanaers.

Q: Debutanizer C4 feed is heated by stabilised gasoline through one 2-4 type exchanger (S = 373 m2).…

A: Given, A= 373m2Design condition are:h= 1200Kcal/h.m2,∘C for 91.5 t/h shell sideh=1370Kcal/h.m2,∘C…

Q: A counterflow, concentric tube heat exchanger is designed to heat water from 22 to 80 deg Cusing hot…

Q: 1ge gas consists of a one-shell-pass, one-tube-pass he exchanger. The oil (c, = 320 F flowing…

Q: Hot oil ( Cp=2200 j/kg.°C) is to cooled by water (Cp=4180 j/kg.:°C) double pipe [shell- tube] heat…

Q: Q3 BA shell and tube heat exchanger with one shell pass and four tube passes uses hot water on the…

A: Heat exchanger Heat exchanger is the device which is used to transfer heat from hot fluid to cold…

Q: a. What is shown in the figure? Where is it used and how does it work? b. What is the nature of heat…

A: (a) The given figure is the image of condenser which is used behind the refrigerator (freeze) to…

Q: Completely solve and box the final answer. Write legibly 6. A counterflow heat exchanger is…

A: To find: The log mean temperature difference. Given: The inlet temperature of hot flue gas is…

Q: Briefly describe the meaning of the efficiency coefficient for a heat exchanger and the parameters…

A: Heat Exchanger

Q: We wish to select a heat exchanger which will yield & = 0.75, using stainless steel fin materials.…

A: please refer handwritten solution

Q: | In a balanced counter flow heat exchanger with mchc = mhhh, the NTU is equal to 1. what is the…

A: Given:mchc=mhhhNTU=1

Q: A highly engineered Ecto-Containment System Protection Grid produces about 8 kW of waste heat in…

Q: The clean U for an exchanger is 770 BTU/(hr 0 F ft2). Its tube area is 550 ft2. After operating…

A: Heat exchanger: It is a system used which is used to transfer heat between two or more than fluids.…

Q: 09:48 Today Edit 09:44

Q: 1. Calculate the (UA) of 3771k12 model at McMaster Carr? With more than three times the pressure…

A: The main basic Heat Exchanger equation is: Q = U x A x ΔTm ΔTm =…

Q: Design a simple piping system to pump water at temperature 130F from a sump below a heat exchange to…

A: Efficiency of the pump = 0.88 = 88%Flow rate = 222 gal/min

Q: Which of the following Fins/Heat exchanger will transfer more heat and why? Justify your answer.…

A: Pin fins are used to increase heat transfer from heated surfaces to air. For the same surface…

Q: For the given temperature profile diagram for a heat exchanger, which of the following equation is…

A: Correct option is:

Q: PLZ I want full answer with all solution steps A heat exchanger is to be designed to heat 32/68…

A: To find: Note: “Since you have posted a question with multiple sub-parts, we will solve the first…

Q: Consider two heat exchanger, one has a parallel flow arrangement and another has a counter flow…

A: Disclaimer: This is multiple questions please upload only one question at one time. In this link…

Q: Show which kind of the double-pipe heat exchanger exchange more heat between the hot and cold water.

Q: Example 3: A condenser using steam from the exhaust of a turbine at a pressure of 4 in Hg abs is to…

A: The heat exchanger is a device used to transfer heat from one fluid to another fluid. For heat…

Q: Counterflow heat exchanger is designed to heat fuel oil from 30-90degC while the heating fluid…

A: Givencounter flow heat exchangerTc1=30oCTc2=90oCTh1=140oCTh2=150oC

Q: A 2-m long thin walled concentric heat exchanger is used to dissipate heat from hot engine oil using…

A: Heat Transfer: According to the second law of thermodynamics, heat is always transferred from a…

Q: 15. Por equivalent inlet conditions, why should a counterflow heat exchanger have better…

A: In the counter flow setup, the liquids are traveling along the heat exchanger in opposite…

Q: -2.a. mass = 2at m and flow rate = 1020 kg /min, rature of hot water is being decreased from a heat…

Q: Single-shell, two-tube pass heat exchanger with surface area 0.4 m2 and overall heat transfer…

A: TS=110°CT1=17°CT2 =?m˙=0.35kg/secCp=4179j/kg-kU= 1800w/m2-k∆T= log mean temp difference

Concept explainers

Heat Exchangers

Heat exchangers are the types of equipment that are primarily employed to transfer the thermal energy from one fluid to another, provided that one of the fluids should be at a higher thermal energy content than the other fluid.

Heat Exchanger

The heat exchanger is a combination of two words ''Heat'' and ''Exchanger''. It is a mechanical device that is used to exchange heat energy between two fluids.

Question

Determine the clearance for the shell and tube heat exchanger with 220 tubes of outside diameter 20 mm, triangular pitch arrangement and one tube side pass.
Bundle Diameter is 422.9 mm and Shell inside diameter is 437.9 mm.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Figure shows a heat exchanger designed to cool 5250 kg/h of an ethyl alcohol solution (Cp = 3810 J/kg. °C) from 66 °C to 39 °C.Water (Cp = 4200 J/kg. °C) at 10 °C is pumped at 4750 kg/h to cool the solution. The tube side fluid flows in a circular pipe with an outside diameter of 25 mm. The overall heat transfer coefficient is (6.84x10^2) W/(m².°C). Find the tube length 'L' for one pass of a two-pass parallel flow double-pipe heat exchanger as shown in Figure. Answer should be in m with three significant figures.
please very urgent what the correct mcq and with solving pls
ENERGY PLANTS: Given : Turbine entry conditions = 16 MPa and 600 oC(Degrees Celsius) Turbine output=5 MPa Phase state saturated water at the heat exchanger outlet and heat exchanger efficiency 85% Required power for district heating = 1100 kW Turbine power= 5500 kW Question: What is the mass flow rate in the boiler?
Find the heat capacity of the hot and cold fluid.
Problem 01 Find the least number of 150 mm diameter pipes required to transmit 170 kW to a machine 3.2 km from the power station, if the efficiency of transmission is to be 90 per cent and f= 0.0075. The feed pressure is 4800 kN/m². Collutate of Pipes required efficiency= Problem 02 A turbine of efficiency 78% is 750 m lower than the supply water source. The pipe supplying the turbine with water is 200 mm in diameter and 4,5 km long. Take f=0,008 and determine the maximum power output that can be expected from the turbine. Problem 03 A pipeline is 1800 m long and 375 mm in diameter, and supply head at inlet is 240 m. A nozzle with an effective diameter of 50 mm is fitted at the discharge end and has a coefficient of velocity of 0,972. If for the pipe is 0,005. (a) The velocity of the jet (b) The discharge (c) The power of the jet C1Reg
PROALEM # 22.a. mass at a pressure = 2at m and flow rate = 1020 kg /min, the temperature decreased from of hot water is being 248.09 °F to 212.09 oF using a heat exchanger. Reservoir water U used as w coolant with mass flow rate = 1800 ka lmin and inlet temperature = 50. 09 oF. The minimum = 270. 17 ft" of heat ex changer 2. allow able surface are a %3D all ow able overall heat = 206.05 btu/ %3D The transfer coefficient of heat exchanger maxi mum 2. The heat Capaci ty to be use d the average valme of must be inlet and outlet temperatures. Find the Number of Transfer units effective ness (NTU) usina if the heat NTU metho d exch anger being used is pipe heal exchanger counter-flow double
show mathematically how the heat transfer coefficient on the boiler side changes with 50% increase in mass flow rate for phase, unchanging heat transfer and turbulent flow on both sides of the tube boiler type heat exchanger and how the heat transfer coefficient by the pipe is affected by 50% increase in mass flow rate.
While thermodynamics deals with equilibrium states and changes from one equilibrium state to another heat transfer deals with systems that have Select one: O a. Fluid equilibrium b. None of the above c. Mechanic equilibrium d. Thermal equilibrium
Below data was obtained from an experimental activity for a parallel pipe heat exchanger. Arrangement: counterflow (cold fluid in annular and hot fluid in tube). Mass flow rate: - Hot fluid: 1.03 kg/s - Cold fluid: 0.91 kg/s Temperatures: - Hot fluid inlet (Th.1): 80.5 +/- 10% °C - Hot fluid outlet (Th2): 64.0 +/- 10% °C - Cold fluid inlet (Te1): 20.0 +/- 10% °C - Cold fluid outlet (Tc2): 41.0 +/- 10% °C Assume cp constant and equal to 4.2 kJ/kg-K. 1. State assumptions (at least 9 unique ones) and include references. 2. What is the log mean temperature difference in °C? 3. What is the heat transfer rate on the cold side in kW? Heat added or lost on cold side? 4. What is the heat transfer rate on the hot side in kW? Heat added or lost on hot side? 5. What is the effectiveness of the heat exchanger for the given conditions? 6. Calculate the propagation of uncertaintv in kW for part 3 (heat transfer rate on the cold side) and part 4 (heat transfer rate on the hot side).
Which of the following sentence is always true for a heat exchanger? Product of overall heat transfer coefficient and an appropriate surface area is independent of the surface area of the tube Overall heat transfer coefficient is independent of the surface area of the tube Hot and cold fluids never come in contact Flow direction of hot and cold fluids are either parallel or opposite
. The gas turbine operating conditions are: Turbine Exhaust 805 Temperature (°F) Pressure (psia) Flow rate (lbm/hr) Density (lbm/ft³) Specific heat (Btu/lbm °F) 0.259 A cross flow plate fin compact heat exchanger is to be used for this heat recovery application. 16.1 196,000 Compressor Discharge 0.0316 347 132 193,000 0.4380 0.251
How do we calculate the heat transfer of a shell and tube heat exchanger.?