Determine the amplitude ratio and phase lag for a standard second order process using substitution rule.

Q: write about consider a adsorption operation in industry and explain in detail the flow diagram and…

A: Adsorption is a separation operation in which the solute gets attached to the surface of the solid.…

Q: Define the two types of stress waves ?

A: The two types of stress waves are to be defined.

Q: Q4. Find the total resistance for the configuration in Fig. 4 R1 R2 2n R3 RT R4 2Ω

A: Given The network of resistors which can be redraun as parallel network.

Q: Apply diffusive Fick's first law on one dimension

A: Mass transfer is the net movement of mass from one location to another. Mass transfer occurs in many…

Q: Express 0.035 seconds in terms of milliseconds.

A: An unit is defined as the measurement of standardized physical quantity. The unit of time is h, min,…

Q: Briefly explain the concept of steady state as it applies to diffusion

A: Diffusion is the process through which particles, molecules, or substances spread or travel from a…

Q: D: Define and draw the Unit Cell and give an example.

A: A unit cell is the smallest element of a crystal lattice that indicates the three-d sample of the…

Q: What is meant by variable underflow and what causes it?

A: The definition of the variable underflow is to be defined along with the cause of it.

Q: In what situations is it more appropriate to use  J-factor chiltern &  colburn analogy than to use…

A: Film theory and Colburn's j -factor analogy is used in flow systems to describe mass transfer.…

Q: What is the basic equation for computing the rate of mass transfer through a membrane?

A: Consider mass transfer through a membrane of area Am takes place from one container with…

Q: 4. Draw the (211) plane on a standard set of x,y,z coordinates.

A: To visualize the (211) plane in a standard set of x, y, z coordinates, we can represent it as a 2D…

Q: Explain flow rate in relation to fluid mechanics

A:

Q: What is potential energy surface (PES)? Draw PES to represent the variation of energy during…

A:

Q: What is Outlet Gas Velocity in a cyclone seperator?

A: In mechanical operation, Cyclone separators are separation devices that use the principle of inertia…

Q: In the forward multiple effect of evaporator The pressure must be decreased from unit to unit The…

A: Multiple effect evaporator : A equipment which has  a congregation of vessels to boil off the water…

Q: on control, with no datum features, can be applied to two or more

A:

Q: Which of the following is the most suitable for extraction in a system having very low- density…

A: Given data Which of the following is the most suitable for extraction in a system having very low…

Q: Which among the following is not a parameter for scaling up stirred vessels? A. Geometric similarity…

A: We have to answer and explain the parameter for scaling up stirred vessels?

Q: 4. List the relations that control the connection of pipes in series, and explain the principle of…

A: Introduction: Flow in pipes: In fluid mechanics, pipe flow is a sort of liquid flow inside a closed…

Q: Do the energy balance for each component of the Carnot Refrigeration System. Illustrate each…

A: carnot refrigeration systen consisits of 4 steps isothermal expansion adiabatic expansion…

Q: you do it in another way especially the F and K part

A: The unit conversion is changing one set of units to an equivalent set of units. Both sets of units…

Q: The selection of pore size of the filtering medium is based on fluid properties only. a.True b.False

A: THE SELECTION OF PORE SIZE : P(R) == 1total pore volume[dVdr]

Q: Present one example depicting the impact of instrumention on one or more process variables.

A: Consider a Water tank with a level controller. Here consider the different process variables. Input…

Q: lowing the wall at x = B to move in the positive z direction at a steady speed vo. Obtain (a) the…

A:

Q: Wave energy can be used in furnaces. Select one: O True O False

A: Wave energy used in furnaces. select true or false.

Q: 17. In the standard notation for a voltaic cell, the double vertical line represents? A. a phase…

A:

Q: QUESTION 7 Tube vibration analysis is not done in calculations.

A: Type of calculation in which tube analysis is not performed is asked.

Q: Traces of solids are removed from, liquid in a a. Rotary vacuum filter b. Clarifier c. Classifier d.…

A: The correct option for the removal of the traces of the solid is to be chosen.

Q: For fixed-bed adsorption, what is the difference between superficial velocity, interstitial…

A: Adsorption is the separation operation. It is fluid-solid operation in which the solute from the…

Q: The settling time of a second-order critically damped system is 1 second, then the damping ratio is…

A:

Q: What is the q-line and how is it related to the feed condition?

A: The definition of the q-line is to be mentioned along with its relation with the feed condition.

Q: Please order the following apparatus in ASCENDING order of resolution; when comparing resolution,…

A: (1) Optical Microscope An optical microscope's highest resolution is about 0.2 microns (200 nm). The…

Q: 2 - What is the use of orifice meter?

A: The flow of fluids is based on density, viscosity, flow rate, etc. These flow rates are measured…

Q: What type of line corresponds to an f value of 0?   a horizontal   b leaning towards the left…

A: Generally the f line or q line represents the quality of feed.

Q: (3) (a) Define process flow sheet or process flow diagram. (b) What does the process flow diagram…

A: (a)Process flow diagram: It is a flow sheet that shows the connections between different major…

Q: Measurment of Down-hole pressure gradient helps us identify the gas-oil contact and oil-water…

A: The drilling of oil wells depends on various factors. The depth that is to be dug to reach the oil,…

Q: The time constant has dimensions of: A time B length (© (dimensionless) (D) energy

A: