A concrete pile 500 mm by 500 mm square cross section is embedded in a saturatedclay. The length of the embedment is 16m. The undrained cohesion, Cu of clay is 40kN/m?, and the unit weight of the clay is 20 kN/m². Use a factor of safety of 5 todetermine the allowable load the pile can carry.d.

Answered: Image /qna-images/answer/54eba3c5-19e3-4b0a-bbbb-079699e2228f.jpg

Answered: determine the allowable load the pile…

Engineering

Civil Engineering

determine the allowable load the pile can carry.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter18: Pile Foundation

Section: Chapter Questions

Problem 18.10P

See similar textbooks

Related questions

Q: What is Group capacity of pile ?

A: Capacity of pile group is that the total of the individual capacities of piles, however it's…

Q: Q3. A 1200-lb hammer falling freely through 3 ft drives a 600lb pile in. vertically into the ground.…

Q: Find the weight of the extra soil needed to be hauled off site after theterrain in the given diagram…

A: To determine the weight of soil that needs to be hauled off after for a formation level of 0 ft.…

Q: The length of the pile required for the above design load

A: This question is from geotechnical engineering

Q: A 500 mm wide, square section pile, 12 m long is driven in a deep deposit of uniform clay. Value of…

Q: Why would it be inappropriate to use the Terzaghi bearing capacity formulas to determine the toe…

A: The ultimate load which a foundation can support is calculated by terzaghi bearing capacity…

Q: What type of pile is least prone to damage during handling?

A: There are many different types of pile foundation available which are used depending upon function…

Q: What are the factors to be considered for the selection of a pile type?

A: The selection of pile type: The selection of piles must be done for the large structure, to prevent…

Q: Define the Types of piles and their functions ?

A: The different types of piles are: 1.End bearing 2.Friction piles 3.Friction and cohesion pile

Q: What are the two methods that are used to determine the capacity developed along the length of the…

A: Pile load capacity depends on a number of factors including cross section, pile length and shape…

Q: How does the Pile capacity can be determined?

A: Piles may either be pushed or casted on the spot. Pile drive is accomplished through: affect lateral…

Q: Define the method of obtaining ultimate load and also allowableload on a single pile from pile load…

A: pile load test is the in situ method of the calculation of the load and settlement. this method is…

Q: In what situation would the LTP be complemented by a pile cap?

A: A pile cap is a mat-like structure made of cement, sand and small scales. This mixture is placed in…

Q: Which advantages fall under which type of pile? Please answer this asap. For upvote. Thank you very…

A: The foundation or substructure of the building is the structure lying below the ground surface to…

Q: What is pile foundation? Discuss the classification of pile based on materials/composition and load…

Q: A timber pile 400 mm in diameter is subjected to the following axial compressive loads: dead =600…

A: Solution Given Data Diameter= 400 mm Dead load= 600 kN Live load= 250 kN earthquake=200 kN Allowable…

Q: Describe representative Pile Load Capacities and Available Lengths.

A: The ultimate bearing capacity of a pile is the maximum load that it can carry without excessive…

Q: Explain the methods of determining load carrying capacity of a pile.

A: Methods of determining load carrying capacity of a pile: Static method : suitable for friction…

Q: Define the functions of cap block, drive cap and pile cushion in driven piles?

A: Solution: Cap Block are generally installed between the end of hammer and the drive cap to control…

Q: Describe the Method of representing pile for wave equation analysis.

A: Wave equation analysis is defined as a method for analyzing the behavior of the drive foundation…

Q: Describe about the Uplift Capacity (Single Pile).

A: The uplift capacity of piles is used to predict the capacity of piles under uplift loading. This is…

Q: Describe the relationship between the capacity of a tested or analyzed pile and the driving record.

A: Relationship between the capacity of a tested or analyzed pile and the driving record is given by…

Q: The length of friction piles based on O Shear strength of soil O Pile size O applied load O all of…

A: 6. The length of friction piles based on: The loads are transferred from the structure to the soil.

Q: Describe a typical structure and subsurface conditions where a pile supported or pile enhanced mat…

Q: What is the ultimate downward load carrying capacity of a single pile driven in soil?

A: The ultimate downward load carrying capacity of single pile driven in soil are : - Using Analytic…

Q: Q 1. Which foundations are suitable to be constructed nearby water retaining structures e.g. dam's…

A: Caisson foundation is suitable to be constructed nearby water retaining structures .Caisson…

Q: SITUATION. A 15m precast concrete pile is to be lifted. If the unit weight of concrete is 23.54kN/m3…

A: let w be the udl over pile w = 23.5x0.4x0.4 = 3.76KN/m

Q: As driven piles penetrate into a saturated clay soil, why the material in the vicinity of the pile…

A: Once a pile is driven into clay, the soil around the pile develops vertical and horizontal…

Q: For marine pile type of steel tubular piles with reinforced concrete infill, minimum toe level is…

A: 1. Reinforced concrete is designed to fill the void space inside the steel tubular piles from the…

Q: In designing the lateral resistance of piles, should engineers only use the earth pressure against…

A: Answer Introduction Lateral load resisted by the following ways 1) Passive soil resistance on the…

Q: Describe the Basic concepts of pile capacity related to soil support.

A: In situations where soil at shallow depth is poor, then in order to transmit the load safely, the…

Q: Determine the maximum load that can be allowed on a 45cm x 45cm diameter bored pile shown in…

A: Calculate the ultimate load carrying capacity of the bored pile, Qu = 133NAb + 0.67N'As N - SPT N…

Q: Discuss the method of obtaining ultimate load and also allowableload on a single pile from pile load…

A: Pile load test is the in situ method of the calculation of the load and settlement. This method is…

Q: Calculate the allowable capacity of the pile shown in the figure-1 considering soil as clay take…

A: Given- qU=17.0KN/m3Clayϕ'=31°Sandγsat=19.0 Kn/m3ϕ'=33°

Q: safe load carrying capacity of the pile

A: Given data, Timber pile having length, l= 8 mDiameter,d= 20 KNFalling freely from a height of, h=…

Q: For a rigid pile cap with vertical piles at the middle and raking piles at the sides,what is the…

A: Brief concept- Piles are provided in the deep foundation where the applied load is very high and the…

Q: Describe about the Relation between pile capacity and driving.

A: The soil that surrounds a pile is substantially disturbed when pile is driven in normally to lightly…

Q: Discuss the ultimate load carrying capacity of the single pile when the pile embedded soil is; i)…

A: In Granular soils the ultimate load-carrying capacity: The pile drives load-carrying capacity from…

Q: A building is to be constructed on driven piles. The downward vertical load on each pile based on…

A: Load on each pile- 120k FOS- 2.5 To determine- Rated hammer energy

Q: Describe the feature of the installation procedure for a driven pile.

A: The piles are used to lay the foundation at hard strata thus getting better bearing capacity of soil…

Q: Please help me solve The soil profile and soil properties at a site are shown in the table below.…

A: Given data Number of Piles =12 n a 3 x 4 matrix L = 12m D = 0.45m Pile spacing 1.5m

Q: A concrete pile is 15 m long and has 406 mm diameter circular cross section. The pile is fully…

A: It is required to find I. Ultimate point load resistance of pile Ii. Total Ultimate skin friction…

Q: 8. Pile Capacity Calculations A 30" diameter friction pile which has a 24' length in contact with…

Q: What is pile foundation? Discuss the classification of pile based on materials/composition and load…

A: Pile Foundation - Pile foundation is type of deep foundation which is used to transfer the building…

Q: minimum length of the pile

Q: What is pile foundation? Discuss the classification of pile based on materials/composition and load…

A: Pile foundation - Pile foundation is the deep foundation that is employed to transmit the building…

Q: What is pile foundation? Discuss the classification of pile based on materials/composition and load…

A: Pile foundation - Pile foundation is the deep foundation that is employed to transmit the building…

Q: . Compute the length (in m.) of the pile if

Concept explainers

Pricing Excavation and Backfill

Backfill, in construction, is the activity of returning the soil and gravel that are removed during building construction or using them again to toughen and support the foundation of the building or any other structural component.

Question

A concrete pile 500 mm by 500 mm square cross section is embedded in a saturated
clay. The length of the embedment is 16m. The undrained cohesion, Cu of clay is 40
kN/m?, and the unit weight of the clay is 20 kN/m². Use a factor of safety of 5 to
determine the allowable load the pile can carry.
d.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A concrete pile 458 mm by 458mm square cross section is embedded in a saturated clay. The length of the embedment is 16 m. The undrained cohesion, Cu of clay is 60 kN/m2, and the unit weight of clay is 18 kN/m2. Use a factor of safety of 5 to determine the allowable load the pile can carry
A concrete pile 458 mm by 458 mm square cross section is embedded in a saturated clay. The length ofthe embedment is 16 m. The undrained cohesion, Cu of clay is 60 kN/m2, and the unit weight of clay is 19 kN/m2• Use a factor of safety of 4 to determine the allowable load the pile can carry.
Evaluate the resisting capacity against axial load due skin friction of a concrete pile embedded into a layer of plastic clay given in the following conditions: Size of pile = 0.4 m square Depth of penetratian inta the clay layer = 40 m Unconfined compression strength (qu) af the clay = 200 KPa Ans. 6400 kN
A 10m long and 0.8m diameter precast concrete pile is driven into a saturated clay deposit as shown in the figure below. The groundwater table is at the ground surface. For the ratio of the undrained shear strength to vertical effective pressure is approximated as follows: = 0.11 + 0.0037(PI) NC (9- 9 (OCR)8 OC Determine the bearing capacity for the pile by the a) Alpha (a) method. b) Lambda (A) method Depth, m Layer 1 OCR = 5, Yat = 19.5 kN/m³, Pl = 35 Layer 2 OCR = 1.5, %at = 19.0 kN/m, Pl = 25 Layer 3 OCR = 8, %at = 19.5 kN/m, Pl = 20 10 D, = 0.8 m D 10 m
QUESTION 3 A concrete pile is driven into top two layers of subsoil strata made of 10m and 5m thick saturated clays respectively. The pile's diameter is 500 mm throughout the pile. Determine the allowable bearing capacity of the pile. The subsoil properties are shown. (Answer 454 kN). Clay layer 1: Saturated unit weight of clay = 18kN/m3 Average undrained shear strength = 100kPa, o = 0 %3D Adhesion factor = 0.48 Clay layer 2: Saturated unit weight of clay = 19kN/m3 Average undrained shear strength = 120kPa, q = 0 Adhesion factor = 0.42, Nc = 9.
FDE 016: A prestressed concrete pile, 400 mm x 400 mm in cross-section, is to be driven in a clayey soil as shown. Use alpha method with factor of safety of 2. Soft Clay 17-15.7 kN/m² c=32 kPa 8 m Stiff Clay * = 19 kN/m² Cu = 90 kPa = 0.5 Refer to FDE 016. What is the end bearing capacity of pile in KN? Select the correct response: 251.84 184.25 129.60 245.32 6 m.
A single pile of diameter 50 cm and length 10 m is driven into clay having unconfined compressive strength of 100 kN/m2. The ultimate load bearing capacity of the pile considering end bearing also will be Nc = 7, a = 0.7). kN. (Take, %3D
Q- A pile of 0.50 m diameter and of length 10 m is embedded in a deposit of clay. The undrained strength parameters of the clay are cohesion = 60 kN/m² and the angle of internal friction = 0. Find the skin friction capacity (kN) of the pile for an adhesion factor of 0.6.
A 600 mm diameter and 25 m long driven concrete pile carries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: Es = 25 MN/m2, Ep = 30,000 MN/m2, and s = 0.2
A steel pile (H-section; HP 360 1.491; see Table 18.1) is driven into a layer of sandstone The length of the pile is 18.9 m. Following are the properties of the sandstone: Unconfined compression strength = qu(lab) = 78.7 MN/m2 Angle of friction = 36 Using a factor of safety of 3, estimate the allowable point load that can be carried by the pile. Use Eq. (18.42).
A 20 m long concrete pile is shown in Figure P12.2. Estimate the ultimate point load Qp by a. Meyerhofs method b. Vesics method c. Coyle and Castellos method Use m = 600 in Eq. (12.28).
Refer to Figure 18.26b. Let L = 15.24 m, fill = 17.29 kN/m3, sat(clay) = 19.49 kN/m3, clay = 20, Hf = 3.05 m, and D = 0.406 m. The water table coincides with the top of the clay layer. Determine the total downward drag on the pile. Assume that = 0.6 clay. FIG. 18.26 Negative skin friction