Determine Ix, Vy, v and i in the circuit shown below. -DA ЗА Žin ODv O Vy Ocv Ix 4 A

UTILIZE THE CIRCUIT ( NEED ONLY HANDWRITTEN SOLUTION PLEASE OTHERWISE DOWNVOTE).

An RTD forms one arm of a Wheatstone bridge, as shown in the figure below and the RTD is used to measure a constant temperature with the bridge operated in deflection mode. The bridge is balanced when the RTD temperature is at 0°C and the resistance R1 is set to 20 N. The RTD has a resistance of 20 2 at 0°C with an a = 0.0045°C-1. If the RTD is subjected to a temperature of 120°C and the output voltage from the bridge is 1.2 Volts, what is the input voltage? R₂ R₁ E₁ Hilllo R3 RTD RRTD

R3-50 Q UTM b) Figure Q4(b) is referred. By using nodal analysis, solve for: 5 UTM i) the values of voltage V, and V; in 5 UTM & UTM ii) the values of current, Ij in phasor domain and time domain UTM MS UTM 5 UTS 5 UTM 5 UTM 5 UTM & UTM 8 UTM 8 UTM 8 UTM 5 UTM 8 UTM 8 UTM R=10 Q UTM & UTM 8 UTM 8 UTM 8 U U XL=j5 Q 8 UTMSN 10020° v A 5 UTM 6 UTM R-20 Q R;=10 Q UTM 5 UTM M 8 UTM JUTM 8 UT 8 UTM 5 UM 8 UTM 5 UTM UTM UTM 8 UTM I-520° A UTM TM 8 UTM UTM 5 UT

OAP 61. For the circuit below, write an expression for vo in terms of the input voltages and resistors. Don't make any assumptions about certain resistors being equal. (This actually makes the problem easier.) V3 V2 V1 Rc RB W RA RD WWW + Vo

Question 3: Breadboard connections of a circuit are given in the figure below. 1- 2- GND .... ...... ...... 0.1µF 10mH 10mH 1kn a) Draw the schematic diagram of the circuit. b) Since we can observe the input signal with Channel 1 and the output signal with Channel 2, what does this circuit do? Write the type and purpose of the circuit. c) Plot the frequency versus transfer function by calculating the required frequencies. Channel 1+ Function generator Channel 2+

LED flashlights use "white" LEDs which have a diode voltage drop of 4.0V. A LED flashlight has the circuit illustrated and will run off several AAA batteries that have a 1.5 VDC rating. a. What is the minimum number of AAA cells needed to turn on the flashlight. b. Would you arrange the batteries in parallel or in series? Vdd R + LED V fritzing

O Given the information appearing in the Figure, Fird the level of resistance for Ri e R3. RI 3 o 14V Rg

Consider the circuit shown below. R1 = 100 N R2 = 100 N C1 10 mF V = 12 V R3 3 100 N C, = 4.7 mF %3D %3D a. After the switch has been closed for a very long time, what are the voltages across the capacitors C1 and C2? Hint for (a) Voltage across C1 is V, and voltage across C2 is V. b. After the switch has been closed for a very long time, what is the energy stored in each capacitor? Hint for (b) Energy stored on C, is J, and energy stored on C, is J.

For the circuit shown, find the expression for the output voltage in terms of Vx, Vy and Vz if the values of the resistors are given as: R1 = 27 k2, R2 = 82 k2, R3 = 10 k2, R4 = 12 kQ, R5 = 39 kQ, R6 = 56 k2. Final %3D %3D %3D answers should be in 4 decimal places. R, R R3 R. Rs CamScanner