Determine: -12v a) Transistor terminal voltages b) Transistor junction voltages 10 kn 2.7 kn B = 75 33 kn 1 kn TY CAT

Q: What is the voltage drop across RC, VC, in volts?  (Enter the number, not the units.)

A: Given circuit is -

Q: 1) A tuned circuit has a 15-mH inductor with a 450-omhs resistance that resonates at 2.3 MHz, a.…

A:

Q: Please write a 1-2 page essay. The essay is about subject of your choice related to Electrical…

A: Topic of essay  power system  Power system is branch of electrical engineering. Power system are…

Q: What is mean by equipment grounding and system grounding?

A: As per bartleby guideline for more than one question asked only first three are to be answered…

Q: It doesn't . . . Very much in .summer rains O / rain / raining O O

A: We have given the following problem

Q: * Problems of using standard ICs are amount of circuit board space, a great deal of time and cost in…

A: Given: problems of using standard ICs

Q: Draw block diagrams which can be used to present the operation of a toaster when it is (a) an…

A: Toaster: Toaster is a small electric device used to heat the bread. There are mainly two type of…

Q: g Technology- Toronto CHAPTER 7: SOLDERING TECHNIOUES ES 7.5 QUESTIONS Which tools will you need for…

A: Note: According to bartleby guidelines, we have to answer only first question. 1) Soldering is the…

Q: 9.a. What should be done with the connector ferrule once a connector is attached to a fiber optic…

A:

Q: Identify the types of batteries used in thefollowing products:a. a laptop computerb. an electric…

A: Battery stores DC current and is used for the backup process when there is no supply current. (a)…

Q: Draw & write crossover cable pin out diagram.

A: According to the given question, it is required to write the Crossover cable pin-out diagram.  The…

Q: 20. Four electricians are discussing wiring under raised floors in information technology equipment…

A: Given, Four electricians are discussing wiring under raised floors in information technology…

Q: GFCI's are designed to trip when they sense a current imbalance of __________ amperes or more.…

A: Ground fault circuit interrupter is a type of protection device that is used to protect the people…

Q: TRUE OR FALSE? Prior period error are corrected current and prospectively.

A: Prior period error It is defined as The financial statements prepared from deletion as well as…

Q: What are the different Impedance matching devices?

A:

Q: External effects causing short circuit include: Select one: a. overloading of equipment causing…

A: Overheating of equipment melts the is insulation layers and causes short circuit. Insulation failure…

Q: appropriate answer. Statement one The most common causes of death are falls from heights and being…

A: a) Statement one is correct and statement two is correctExplanation:Statement one states two of the…

Q: I have a wooden toy train that runs on wooden tracks. I would like to place two ESP-WROOM-32 Boards…

A: According to the question we need to design a wooden train that runs on wooden track.What's the…

Q: 21. Which voltage range that is sometimes called a “float" in TTL circuits?

A:

Q: Can you tell me about cables that utilize the F connector?

A: We have to explain about cables that utilize the F-connector.

Q: Create a simple functional high-level control system block diagram for each of the descriptions…

A: It is asked to create a simple functional high-level control system block diagram for a Grid-tied…

Q: 31. What is the difference between electrical con- ductivity and resistivity?

A: we need to find the difference between electrical conductivity and resistivity.

Q: What is the difference between passive and active buzzer?

A: A passive buzzer requires an ac signal to make a sound. A passive buzzer does not generate a tone by…

Q: Please answer the two questions, and in the other picture are the drawing we had made. (Which are…

A: Given: Consider the figure (that shows the schematic symbol(types) of electrical loads, switches,…

Q: The ________parameters may not reflect the actual operating conditions but simply provide an…

A: For the AC analysis of BJT or MOSFET based circuits, It is important to convert it into different…

Q: Compare the nested and the NPC topologies in terms of the blocking voltage for the switches employed…

A: We need to compare NPC and Nested topology.

Q: Write the following number in four methods: (2002) *

A:

Q: Give at least two separate reasons why it's advantageous to wire holiday lights in parallel. (Ask…

A: All the holiday lights are designed to operate on a standard voltage, it must be connected in…

Q: 3- Draw the Experimental setup of the short – circuit Test.

A: The  short circuit test meant for the LV side ( Low voltage side).  The experimental set up can be…

Q: Electrical hazards include electrical arcs, blasts, and broken or faulty equipment. a. Polished O b.…

A: The correct option is shock.

Q: Draw bread board connection diagram for full adders along with tables and pin configuration of ICs…

A: Full adder truth table: Thus, Sum, S=X⊕Y⊕Cin and Carry, Cout = (X*Y) + ((X⊕Y)*Cin) So, the circuit…

Q: if you have (10) 10 OHM resistors and (5) OMR resistors in a series circuit what would the total…

A: Resistances are given as,

Q: a. What is meant by transmittive cell type in LCD construction

A: According to guidelines we need to solve only the first question. According to the question, we need…

Q: At pinch-off voltage, the drain current in a FET is ___. Choose the correct answer: a.zero…

A: At pinch-off voltage, the drain current in a FET is ___.   Choose the correct answer: a.zero…

Q: Mention the applications of FET.

A: FET stands for field effect transistor. Applications of FET FET is used in the multiplexer. FET is…

Q: If you dont have a vise to hold a EMT conduit what other two methods could you use to hold the EMT…

A: To hold the EMT conduit in place while cutting with hacksaw, following items or methods can be used…

Q: How Rth connected with the load resistance, explain

A: RL will be  connected in series with  RTH  as shown in the example.

Q: On a short/long bond paper, draw a schematic circuit diagram following your house wiring with…

A: electrical wires are designed to bear consistent electric current which should not lead to a fire in…

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.