Design data is required for the improvement of two-way highway with present AADT is (2500 veh./day) in both directions. The improved road with a design life of (25

Q: Two members are connected by pin at point B and loaded as shown: 114.81 N 721.56 N 215.36 N B 75°…

A:

Q: What is the strain ratio, R = √( Rmax Rmin)? (see eqn. 12.2, page 307) 4.8 O 1.0 02.0 3.8 3.0

A: The given figure is shown below:

Q: e section are given by the table. The beam is subjected to the concentrate the couple moment Mo…

A:

Q: B 7m |C A 5m 6m 8m

A: Given: A tank filled with lubricant oil exerting 150 kPa Required: To find vertical stress increase…

Q: Problem 2: Determine the centroid X-bar with respect to Y-axis -150 mm 15 mm C 150 m -15 mm 15 mm…

A:

Q: 1-2in. -1in-+1int Hin 3in- T 3in 2in

A:

Q: & Find the set of solutions xy dx + (y-3x²) dy = 0. %3D

A:

Q: ) Determine AT 2.) Determine Centroid about y(x) 3.) Determien centroid about x (y)

A:

Q: Problem:- hecate the centrosd for channel section love x:?→*=322-22m- 20u mm 2 uumn

A: To find the centroid of a C section-

Q: Please use geometry instead of sin & cos when solving. Find Ax,Ay,Bx,By,Cx,Cy

A:

Q: A cube of edge 24mm is resting on the top of a frustum of cone of base diameter 60mm and top…

A: In the engineering graphics we can draw both the 2 dimensional projection and 3 dimensional…

Q: y at a distance 3m From 20 KN lom' OF R.1 21 R2

A: To find deflection at 3m from R1

Q: 1 2 T - 3 CONCACA NIDO Force diagrams - Inclined plane 5 Performs various tests by modifying the…

A:

Q: y 200 mm 300 mm → 125 mm 125 mm 60 mm 150 mm

A:

Q: Q.: Find the coordinate of the centriod of the shaded area 4 Y 3 m-

A: Given, Equation y=2x-30.5

Q: 4. From the figure shown, Determine, e. Centroid with respect to x-axis f. Centroid with respect to…

A: Find centroid with respect to X and Y axis  Find moment of inertia with respect to centroid of X and…

Q: Why Nc=9 and Nq=1

A: Given question is based on static method of analysis bearing capacity of pile.

Q: 136 N is the asnwer in the

A:

Q: Determine the XT and YT a. Using the Top Most, Left Most Reference Line b. Using the Bottom Most,…

A:

Q: Determine the location of the centroidal x an y of the figure shown.

A: The portion which is cut out needs to be subtracted.

Q: determine the reading at "D"

A: A levelling staff is given, we need to find out the reading at D

Q: The speed of the collar B is 400 mm/s up and the change of velocity of B is 100 mm/s^2 down. Please…

A: Angular velocity is defined as the rate at which an object revolves about an axis .  Therefore,…

Q: 3. A 12m beam simply supported at 1.3m from both ends carries a uniformly distributed load of 18KN/m…

A:

Q: y=(x^2+2x+1)(x-4)

A: The given equation is: y=x2+2x+1x-4 Adopt substitution method for determining the roots of the given…

Q: Flow and spacing are inversely related O True O False

A: State true or false Flow and spacing are inversely related

Q: Q1: Answer with (True) or (False) with correcting the error if the same: 1- When you start drawing…

A: As per company guidelines, we are supposed to answer only first three sub-parts. Kindly repost…

Q: Problem 10.6 - Locate the centroid of the section and determine the moment of inertia of the beam…

A:

Q: Make use of Simpson's rule to calculate the work done W by the gas on the face of the piston.

A: The expression for internal of volume is given as ∆V=V2-V1 Substitute the value in above expression…

Q: E = 29x 1.' ksi Í 6odiut

A: 1. Determine the fixed end moments FEM for span with udl=wl212FEM for span with point load at centre…

Q: There are support reactions Ay and By which both equal 3.5kN going upwards.

A:

Q: Let F₁ = [F1] N. i) Express F₁ as a Cartesian vector. F₁ X 3 5 4 30° 45° F₂= = 450 N - y

A: To represent F1 as a Cartesian vector. F1 = 647 N

Q: F: 300 N 60 120 4S 45' F: S00N F: F, (-cos bo sin 45 i cos bocos 4sjt sin l6ok)

A: first of all take components on X-axis and note take negative sign when force component showing…

Q: CORRECT ANSWER

A:

Q: a = 20 mm b = 100 mm c = 200 mm d = 70 mm e = 60 mm f= 70 mm g= 50 mm h = 20 mm

A: Given  a= 20mm b= 100mm c= 200mm d= 70mm e= 60mm f= 70mm g= 50mm h= 20mm second moment of area about…

Q: Determine the X¡ and YT(using both a and b) a. Using the Top Most, Left Most Reference Line b. Using…

A:

Q: х —у (10) lim (x ,y)>(2,2) x * - y * 4

A:

Q: Could you explain the table on what is K1 - K3? This is the main issue I've been having with virtual…

A: Given:Required:To explain what is K1, K2 and K3.

Q: The reduced form of 3y (0) – 21y (4) + 5y''– 10y"+42y'- 8y+ 5=0 js: A (3D5- 21D4+5D³ – 10D²+42D – 8)…

A:

Q: 22. From a triangular steel plate XYZ, a triangular section VWZ was cleanly cut off. What should be…

A: Value of x is to be determined for which the line YWZ remains horizontal