Design an RLC bandpass passive fiter iparallel LC) if =5 KHz, C-lpF, =1KHz,A) Draw the circuit, laheling the i/p and olp and drive an expression for HaB) Determine the value of R. L, oa,0a and QC) Find V. at enaif vat)= 1 sin(ot).D) Sketch (approximately) the gain and phase shift versus en, indicating e, eki, enaE) Determine the new value of if a load of 1000 is applied to the filter and the sourcehas Rin-10 2

Design an RLC bandpass passive fiter iparallel LC) if -5 KHz, C-luF, =1kHz, A) Draw the circuit, laheling the /p and afp and drive an expression for Ha B) Determine the value of R, L, oa,o2 and Q. C) Find V. at en aif Fat=1 sinfot). D) Sketch (approximately) the gain and phase shift versus en, indicating en, e1, en E) Determine the new value of if a load of 1000 is applied to the filter and the source has Rin=10 0

Design an RLC bandpass passive fiter iparallel LC) if -5 KHz, C-luF, =1kHz, A) Draw the circuit, laheling the /p and afp and drive an expression for Ha B) Determine the value of R, L, oa,o2 and Q. C) Find V. at en aif Fat=1 sinfot). D) Sketch (approximately) the gain and phase shift versus en, indicating en, e1, en E) Determine the new value of if a load of 1000 is applied to the filter and the source has Rin=10 0

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the circuit in the figure, extract the following as the formula according to r model and π model. a) IB, IC and IE currents b) The voltages at the X, B, C, E points and the voltage VCE c) Ri input resistance and output resistance Ro d) Av Voltage gains e) Low cutoff frequencies f) Formulate the high cutoff frequencies.
Design a 3 Band Equalizer based on the following requirements. Use standard component values on your circuit design. The design specification values have a tolerance of +/- 3% of the rated value for cut/boost while a tolerance of+/- 10% of the rated value for frequency values
The spectrum of an analog signal extends up to 4 kHz and has a peak value of 4 V at 0 Hz. It is naturally sampled by a 10 kHz pulse train with a pulse width of 25 usec. The value of the spectrum of the sampled signal at 40 kHz is given by: O 2v2 V. O 4/pi. O Ov. O 4 V. O pi/4.
For the signal and circuit below, determine the maximum frequency that may be used. Op-amp slew rate is SR = 0.9 V/us. Refer to the image for the circuit, but refer to the following for the given values: Rf = 323996 ohms, Ri = 14089 ohms, Vi = 0.03 C, and w = 404604 x 10^3 rad/s. Express your answer in 10^6 rad/s, no units required, round-off up to two decimal places.
A step-up chopper has input voltage of 220v and o/pvoltage of 660v. If the non-conducting time of the thyristorchopper is 100μs compute the pulse width of the outputvoltage . If the pulse width is halved for constant frequencyoperation Find the new output voltage and chopper frequency
BW mssege signai COTier. i) Draw the modulated signal in ii) find the bandwidth of the modulated signal ii) What is phase reversal and we could avoid it? frequency domain, (AM)
The circuit is shown below, Vin is the sinusoidal waveform with magnitude 5V and frequency is 100 Hz, R = 1 k, C = 1 uE, the chip is supplied by + 12 V source. a) What is the waveform of Yout? b) Calculate the magnitude of Vo c) If Vin is triangle waveform, what is the output waveform? -Vout , if Vin is triangle waveform with magnitude of 5 V (peak-to-peak value is 10 V) and frequency is 10 kHz, calculate waveform of you and the magnitude of I/?
What is lead compensator? Draw its circuit diagram and derive the expression for the transfer function of lead compensator. Solve it fast fast plz
We examined the common source amplifier shown in the figure in the 5th experiment. The selection criterion of the input capacitance is Xcin = 0.1Rin: Calculate the required input capacitance value, Cin , if an input signal with a frequency of 2 kHz is applied. Şekitde gösterilen ortak source yükseltecini 5. deneyde incelemiştik Giriş kapasitesinin seçim kriteri Xcin - 0.1Rin dir. 2 kHzlik giriç sinyali için gerektt tapasite, Cm değerini hesaplayınız. Circuit parameters / Devre Parametreleri R1 = 53 k2, R, = 17 k2 R1 RD Cout Vout D VDD M2 Cin G Vin R2 RS cs O a. 74.19 nF O b. 86.55 nF O c. 49.46 nF O d. 61.82 nF O e. 43.28 nF
For the Following Cirucit Calculate: Voltages gain vo/vin., Input resistance Rin., and the Overall voltage gain vo/vsig for when C3 is removed.
Consider the Circuit shown below: Rf Ri Vin Vo Solve for the output voltage Vo in mV if Rf=13.07kOhms, Ri=3.60kOhms and Vin=2.40mV.
Give the different types of filters and briefly discuss each