( The comparator compares two analog voltages on its tarminals.()Design an alam using comparators basod on the inputs from atemperature transducer and a pessure transducar. The alarm (4) istriggered when the temperature (T) exceeds 100 °C or the pressure (P)excceds 10 kPa The transfer function of the temperaturc transducer andpressure transducer is 2.0 mVPC and 0.15 V/kPa, respectively. Assumethe output of the transducers is free of noise. Sketch the circuit diagramwith proper labeling.(i)The testing of the circuit (the solution of Q5 (b)i)) reveals that thetemperature transducer suffcrs from a static noisc of +4 °C. Modify thecircuit in the solution of QS (b)(G) to provide a hysteresis window of 10°C in order to eliminate the fluctuation at the output of the temperaturetransducer. Assume the output voltage of the comparator is 5 V at highstate and the feedback resistor (R) is 250 kQ. Ihustrate the circuit in adingram with proper labeling.

Answered: Image /qna-images/answer/5381fe2d-6f57-426e-9cfa-2040e63a3f9a.jpg

() Design an alam using comparators basod on the inputs from a temperature transducer and a pressure transducar. The alarm (4) is triggered when the temperature (T) exceeds 100 °C or the pressure (P) excceds 10 kPa The transfer function of the temperature transducer and pressure transducer is 2.0 mVPC and 0.15 V/kPa, respectively. Assume the output of the transducers is free of noise. Sketch the circuit diagram with proper labeling. (ii) The testing of the circuit (the solution of Q5 (b)i)) reveals that the temperature transducer suffcrs from a static noisc of +4 °C. Modify the circuit in the solution of Q5 (b)(i) to provide a hystcresis window of 10 °C in order to eliminate the fluctuation at the output of the temperature transducer. Assume the output voltage of the comparator is 5 V at high state and the feedback resistor (R) is 250 k. Illustrate the circuit in a diagram with proper labeling.

() Design an alam using comparators basod on the inputs from a temperature transducer and a pressure transducar. The alarm (4) is triggered when the temperature (T) exceeds 100 °C or the pressure (P) excceds 10 kPa The transfer function of the temperature transducer and pressure transducer is 2.0 mVPC and 0.15 V/kPa, respectively. Assume the output of the transducers is free of noise. Sketch the circuit diagram with proper labeling. (ii) The testing of the circuit (the solution of Q5 (b)i)) reveals that the temperature transducer suffcrs from a static noisc of +4 °C. Modify the circuit in the solution of Q5 (b)(i) to provide a hystcresis window of 10 °C in order to eliminate the fluctuation at the output of the temperature transducer. Assume the output voltage of the comparator is 5 V at high state and the feedback resistor (R) is 250 k. Illustrate the circuit in a diagram with proper labeling.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What will be the CMRR of an opamp if the value of the common mode gain is 100 and the value of the difference gain is 106?
10. What is the use of the compensation capacitor in op-amp? a) Improves the amplification of op-amp b) Decreases the slew rate of op-amp c) Increases the bandwidth of op-amp d) Op-amp acts as all pass filter
8. If the CMRR of a practical op-amp is 108 dB and the common mode gain is 0.4, the open loop gain is: a) 100000 b) 200000 c) 400000 d) 500000
6) i need fast please now
What is the frequency of oscillation of the Astable Multivibrator circuit. Sketch the Vo and showcomplete details. Opamp is 741 with Vcc = 15V and VEE = -15V Rin = 2M ohm Rout = 75 ohm Open-loop Gain = 200000
Figure 3 shows a Hartley oscillator. Assume that the op-amp employed in the figure is an ideal op-amp, and R1= 20 kΩ, R2 = 60 kΩ, L1=10 mH. b) State the Barkhausen criterion for sustained oscillation.c) Explain briefly how the phase shift requirement for sustained oscillation ismet in the circuit of Figure 3.d) The feedback ratio and oscillation frequency of Figure 3 are givenrespectively by, B = -L2/L1 and w0 = 1 / sqrt(L1 +L2)C Determine the values of C and L2 in order for the circuit to oscillate at a frequency of 200 Hz.
File Edit View For an operational amplifier, the common mode gain is 0.1 and the differential gain is 1000. What will be the CMRR of the opamp?
If in the oscillator block diagram shown in Figure, = 0.1V, A = 100 and m = 0.01, then the circuit will. V₁ mVo Voltage Gain A Feedback Circuit V
VIN = 300mV. Determine i, (the current sourced by the op amp) ? 1002 1002 +15 V B=10 100- Vo a. 0.30mA O b. 25.0mA Re call: for BJTA in the active ragion c. 6.00mA o d. 9.00mA e. 0.90mA :VE
A positive-feedback amplifier circuit (inverting Schmitt trigger) is shown in the following figure. In each of the situations below, determine output voltage given the applied trigger signal verigger, initial output vout and power supply rails ±Vcc, where Vcc = 15 V. The first three questions start the circuit in the positive stable state, the next three start the circuit in the negative stable state. 3 k. 2 k. レナ Vout OV O Vrigger
5) CONSIDER THE A/D CONVERTER BELOW WITH A STEP OF 0.1MV, CLOCK FREQUENCY OF 10MHZ, FULL SCALE OF 10.23V, AND OUTPUT OF 10BITS. VAX Ampl. op. Comparador Conversor D/A EOC Resultado digital RESET Contador CLOCK Start Clock rr DETERMINE THE DIGITAL EQUIVALENT AND CONVERSION TIME FOR THE FOLLOWING VA VALUES: A) 3.728V B) 5.0 V C) 8.235V
Fill in the blanks in the following sentences: 2 The value of the attenuation of the feedback circuit in the phase shifi oscillator is...................................