Design an air stripping column to remove TCE from water (i.e. determine the stripping factor, the height and number of transfer units, and the height of the packing in the column). The initial concentration of TCE is 1.3 mg/L and this must be reduced to 75 µg/L. Use the following criteria: water flow rate of 350 gal/min; air to water ratio of 70; water temperature of 16°C; air temperature of 23°C; column diameter of 2 ft; 2-in Intalox saddles for packing material; liquid mass transfer coefficient of 20.4 cm/hr; design safety factor of 20% ; and tower height(s) between 1-15 m.

Design an air stripping column to remove TCE from water (i.e. determine the stripping factor, the height and number of transfer units, and the height of the packing in the column). The initial concentration of TCE is 1.3 mg/L and this must be reduced to 75 µg/L. Use the following criteria: water flow rate of 350 gal/min; air to water ratio of 70; water temperature of 16°C; air temperature of 23°C; column diameter of 2 ft; 2-in Intalox saddles for packing material; liquid mass transfer coefficient of 20.4 cm/hr; design safety factor of 20% ; and tower height(s) between 1-15 m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Assessment Details and Informat WP NWP Assessment Builder UI Appl x WP NWP Assessment Player UI Appli x + A education.wiley.com/was/ui/v2/assessment-player/index.html?launchld=976e1b4d-00fd-478f-90e4-65cfc7f564eb#/question/2 e M1 Removal Exam for CE O 58 : 58 Question 3 of 5 -/ 20 > View Policies Current Attempt in Progress A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 580 mm2. If the stress in the bar must not exceed 330 MPa and the maximum deformation in the bar must not exceed 13 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 4 m, b = 2.4 m, and c = 5.2 m. (1) B a Answer: P = i kN Save for Later Attempts: 0 of 1 used Submit Answer 4:01 pm e Type here to search ENG 13/04/2022 19 ... ...
In addition to furnishings, give the list of other equipment required by the owners,and engineers?
What is UBC Standards?
Handwritten answers only pls. make FBDs identical as the lay out is given
What is the construction process and component requirements for a control unit utilizing vertical coding?
What are the Errors and omissions in the plans and specifications?
A CPLD is precisely what?
Discuss SERVICEABILITY LIMIT STATES
6- Which one of the following store layout is the most expensive design? a. Mixed floor layout b. Geometrical layout c. Diagonal layout d. Angular layout
Discuss about CONSTRUCTABILITY REQUIREMENTS
Gradebook/MECHANICS OF DE X WP NWP Assessment Builder Ul Appl X WP NWP Assessment Player Ul Appli X b Home | bartleby ✰ education.wiley.com/was/ui/v2/assessment-player/index.html?launchId=0c1dc9a6-6521-4dbc-abf2-b162fae20948#/question/5 CE104.3T.22.23 Formative Assessment 4 26°C Mostly cloudy Question 6 of 6 Z (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. Aluminum C A composite beam is made of two brass [E = 112 GPa] bars bonded to two aluminum [E = 71 GPa] bars, as shown. The beam is subjected to a bending moment of 260 N-m acting about the z axis. Using a = 5 mm, b = 35 mm, c = 10 mm, and d = 25 mm, calculate Aluminum Answers: (a) Jal= Brass (b) Obr= i Brass a d MPa MPa O Search X 49 (2) Facebook JA - / 10 E O : + ENG US 8:36 pm 01/05/2023 X ⠀
What is a Floor Plan?