Design an 8 x 5 bit Mask ROM, which is programmed as a (Y+1) bit Full Adder circuit so that if a user gives any input to its input lines, the corresponding binary output will be appeared on its output line. Provide necessary truth table and denote cell 1 and cell 0 using mask ROM cell. [Y = Last digit of your ID; For example, ID = 12-34567-1, Y = 1]

Design an 8 x 5 bit Mask ROM, which is programmed as a (Y+1) bit Full Adder circuit so that if a user gives any input to its input lines, the corresponding binary output will be appeared on its output line. Provide necessary truth table and denote cell 1 and cell 0 using mask ROM cell. [Y = Last digit of your ID; For example, ID = 12-34567-1, Y = 1]

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Procedure: 1. Design an even/odd parity generator for 4-bit data. 2. Design a parity checker circuit for a 4-bit data. 3. Design a logic circuit for a 3-bit message to be transmitted with an even parity bit. 4. Four data bits are to be transmitted. Design a parity bit generator to give an o/p of 'l' if the number of logic l's in the message is: (i) odd; (ii) even.
Draw a dataflow circuit using block components that lets you add or subtract two input numbers in all possible ways. Your circuit will have two inputs X, Y and one output Out. You’ll have an adder and you’ll need to use multiplexers on each input to the adder. Clearly specify the number and type of control bits needed.
Suppose RO contains "Ox02145321" and R1 contains "Ox00200020", and the C bit of the APSR is set to 1. What is the value of R2 after the following line executes? (enter this value in decimal) ADD R2, R1, RO
Write a program in assembly language to toggle PORTB 400 times. Use BNZ instruction.
Question 2: The HCS12 registers have the values shown in the attached table.Where X, means the values is undefined. Answer the following:A. What is the HCS12 operational mode?B. What is the value on port B pins?C. What is the value on pins PT4-PT7?D. What is the value of X in PTT register?E. Is port B working in full or reduced power?F. What is the pins configuration of CAN2 and CAN4?
3. Convert 14.578 (unsigned) to decimal with accuracy of 4 digits if rounding is necessary. 4. Convert 7654.76548 (unsigned) to hexadecimal. 5. Calculate 11010110-10110111 (unsigned) and express the result in decimal. 6. Extend the following binary numbers from a 4 bit wide integer with 4 bit fraction system into an 8 bit integer with an 8 bit fraction so the same value is represented. First, assume the numbers are signed binary numbers. a) 0110.0100 b) 1010.0001 c) 1100.1 d) e) f) Now repeat, assuming a, b, c are unsigned numbers.
Q1) Write the assembly language instructions required to convert negative numbers to positive numbers, for a block of data of size 2kbytes stored at starting address: 6A000H in the data segment, each of these numbers is an 8-bit signed number.
con con of son The first 2 pins of the analog pins in Arduino are used to transmit and receive data (TX and RX) O a. False O b. True Which of the following parameters is not a required part in the ARDUINO sketch "for" loop? O a. Initialize O b. Increment OC. Serialprint O d. Condition When an overflow occurred, the C bit in the STATUS register is O a. None of these O b. 0 Oc. Not affected Od 1
In a DPCM system, the number of bits per sample is 7. How many levels are present in the quantizer?
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
A) What are the addressing mode and physical address for each instruction if you know Ds=4200H,SS=D000H,BX=0200H,BP-1000H, DI-0300H and Sl=0400H ES=1A00H, .[Source operand of MOVAL, [SI+8(1 .Destination operand of MOV [BP+DI],AX(2 .B) Define interrupt and DMA? list the types of interrupt
Let A = ajao and B = b¡bo be two-bit binary numbers. A and B can take on values from 0 to 3 (for example, A = 2 when a1ao = 10. Let C be a two bit binary number whose value equals the magnitude of the difference A – B. We have C = c1c0 = |A – B|. (This means that if B is larger than A then you consider B-A.) You are to design a circuit which accepts A and B (i.e., a¡ aob¡bo) as inputs and outputs the result C = c¡c0. The circuit thus has four inputs and two outputs. For example, the circuit should output c1co = 10 when ajao = 01 and bibo = 11 (C = 2 when A = 1 and B = 3). - Your pre-lab needs to include all items requested in the following steps (plus those requested in the pre-lab handout): 1. After reading through the complete lab, write a description of the expected behavior of the system you will design. 2. Draw a truth table describing the behavior of the circuit. The truth table should show the inputs: aj aobibo (in this order) and the outputs: c1Co · 3. Write the canonical SOP…