Design a voltage divider biased common emitter amplifier with a bypassed emitter resistance for a DC supply of Vcc= (18 + R)V and a quiescent current of 2mA. The voltage drop across collector should be 40% of DC supply voltage For the given design conditions: R = 02 Compute the circuit resistances.biased values of voltages and currents. Draw the completely labelled circuit diagram.

Design a voltage divider biased common emitter amplifier with a bypassed emitter resistance for a DC supply of Vcc= (18 + R)V and a quiescent current of 2mA. The voltage drop across collector should be 40% of DC supply voltage For the given design conditions: R = 02 Compute the circuit resistances.biased values of voltages and currents. Draw the completely labelled circuit diagram.

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Chapter2: Electrical Components And Circuits

Section: Chapter Questions

Problem 2.1QAP

See similar textbooks

Similar questions

The molar absorptivity for aqueous solutions of phenol at 211 nm is 6.17 x 103 L cml mol-'. Calculate the permissible range of phenol concentrations if the transmittance is to be less than 85% and greater than 7% when the measurements are made in 1.00-cm cells.
2. The following data were obtained for a voltage measurement, in mV, on a noisy system: 1.27, 1.54, 1.45, 1.63, 1.68, 1.39, 1.40. Assuming the noise is random, and s-0.145, what is the signal-to-noise ratio? A) B) C) D) 0.098 1.48 10.2 0.228
What is the purpose of waiting 1s after a voltage pulse before measuring current in sampled current voltammetry?
FIGURE 24-8 2µF 4µF HH 3µF HH 6µF 90V A system of capacitors is connected across a 90 V DC voltage source as shown in Fig. 24-8. What is the equivalent capacitance of this system?
Electrochemical detection is commonly used in combination capillary electrophoresis systems. This is a type of hydrodynamic voltammetry called flow injection, where it has been shown that ilim a U1/3, where U is the flow rate of the solution. Flow analysis of a urine sample at a thin-layer amperometric detector, with a flow-rate of 1.25mL/min, yielded a limiting current value of 1.6µA for its unknown uric acid content. A larger current of 2.4µA was observed for a sample containing 1 × 10-4 M uric acid and flowing at a rate of 0.9mL/min. Calculate the original concentration of uric acid in the sample
A solution containing 4.48 ppm KMnO, had a % transmittance of 30.9% in a 1.00 cm cell at 520 nm. Calculate the molar absorptivity of KMnO, at 520 nm.
At 520 nm with a 1.00 cm cell a 8.24 ppm solution of KMnO4 has a transmittance of 0.126. What is the molar absorptivity of KMnO4 at 520 nm?
1. A compound has a molar absorptivity of 3.031 x 10° L cm1 mol1. If a 15.00 mm-length cell is used to hold the sample, and a transmittance of 19.53 % is measured, what is the molarity of the compound in solution?
The table shows a series of standard additions of Cu(II)to acidified tap water samples measured by anodic stripping voltammetry at a platinum electrode. The unknown and all standard additions were made up to the same final volume. 1. Plot absorbance as a function of the concentration of Cu (II) standard. Determine the equation of the line and the X intercept. Find the concentration of Cu(II) in the water.