design a Pined Reinforced Concrete frame supported equally by two columns which should satisy the following: max: 55 trength fck: 29 Mpa Breadth (b) and depth (d) <0.15 m, Max weight = 60 kg Steel reinforcement: Longitudinal Reinforcement diameter = 9 nm (yield strength 500 MPa), Stirrups diameter = 4 mm (yield trength 400 MPa)

design a Pined Reinforced Concrete frame supported equally by two columns which should satisy the following: max: 55 trength fck: 29 Mpa Breadth (b) and depth (d) <0.15 m, Max weight = 60 kg Steel reinforcement: Longitudinal Reinforcement diameter = 9 nm (yield strength 500 MPa), Stirrups diameter = 4 mm (yield trength 400 MPa)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Homework3 A simply supported concrete slab given the section depth is 100mm, concrete grade is C30 and reinforcement grade is HPB300. The span of slab is 19=2.38m. The live load applied on the slab is ge=2kN/m2 and the dead load include: 1. Its self-weight given concrete (include reinforcement) bulk density is 28kN/m3 2. Terrazzo floor and fine stone cushion layer is 30mm(bulk density is 22kN/m) and the ceiling plaster mortar is 12mm(bulk density 17kN/m²).
A rectangular beam has a width of 300mm and an effective depth of 537.50 mm to the centroid of tension steel bars. Tension reinforcement consists of 6 – 28mm dia in two rows, compression reinforcement consists of 2–22mm dia, fc’ = 27.6MPa, fy = 414.7MPa, d’ = 60mm, L = 4m, the Unit weight of concrete is 24.56kN/cu.m 1.) The depth of the concrete stress block is ____ mm.
3 A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.0 m, web width of 250 mm and overall depth of 500 mm. The tensile reinforcement consists of 6-∅20 mm bars in two rows with 25 mm vertical clear spacing. Use material strengths f’c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = ? Depth of uniform stress block at ultimate stage in mm to the nearest whole number = ?? Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places = ?
R.Bars.
A rectangular beam has a width of 300mm and an effective depth of 537.50 mm to the centroid of tension steel bars. Tension reinforcement consists of 6 - 28mm dia in two rows, compression reinforcement consists of 2 - 22mm dia, fc' = 27.6MPa, fy = 414.7MPa, d' = 60mm, L = 4m, the Unit weight of concrete is 24.56kN/cu.m If the beam is simply supported carrying a uniformly distributed dead load of 10kN/m, a uniformly distributed live load of 5kN/m, the safe concentrated live load that it could carry acting at the midspan is _________kN. IS 456:2000
a simply supported beam 300mm wide, 500mm deep and spans 5.7m supports a service super imposed dead load of 8kN/m and service live load of 7kN/m. concrete strength f'c=21MPa and steel yield strength fy=415MPa. concrete cover to bar centroid is 70mm. determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015.
30" Design the reinforcement for the T-beam in the middle which carries a live load of 200 lb/ft². The length of the beam is 25 ft. In your design assume concrete with a compressive strength of 3,000 psi density 150 lb/ft³ and Grade 60 Steel. 27" 12" 10'-0" 12" 10'-0" 12"
5. The beam shown is reinforced for positive moment with three epoxy-coated #11 bars. The bars terminate at the center of the supports. Neglecting beam weight (concentrated loads are very heavy), determine if the required development length is satisfied. Assume As required = 4.55in², 2 in. clear cover on all sides of the longitudinal reinforcement, normal weight concrete, #3 stirrups @12 in o.c., f'c = 5000 psi and fy = 60,000 psi. 8 ft | Pu 20 ft Pu 8 ft ge2 of 56 30 in b=14in. ed 5/15/2020 As = 3-#11
Q2// A floor system consists ofconcrete slab supported by continuous beam h = 140mm , bw = 300mm,d = 550mm, f 28MPA, fy = with: %3D 420MPа. Determine the steel reinforcement required at mid span of interior beam to resist service dead load moment Ma = 320KN.m and service live load moment M = 250 kN.m %3! %3D 8m + 3m 4 3m 3m 1-1
The middle of the 5.6 m simple beam has a dimension of 350 mm by 600 mm. On that location, the beam is reinforced with 3-020mm on the top and 7-020 mm at the bottom. The concrete cover to be used is 40 mm. The stirrups used is 12 mm in diameter The concrete strength of the beam is 27.6 MPa. All reinforcement used is Grade 60 (y = 420 MPa). The beam is carrying a superimposed dead concentrated load of 55 kN and an unknown superimposed live load both at the midspan. The unit weight of concrete used is 23.6 kN per cubic meter Determine the unknown concentrated live load that the beam can sustain.
( CECE2240 - Design of structure -1 ) EXPERIMENT :Designing and detailing of singly reinforced simply supported beam - ACI Code Step 1 Step 2 Step 3 Step 4
Question 2: Determine the required reinforcement for L section beam to resist torsion T = 10KN.m with the following dimensions; depth of slab = 100 mm, width of flange = = = 200 mm, 900 mm, width of web depth = 455 mm. Consider concrete class C30 and high yield steel S460 for main Reinforcement and S250 For stirrups. 900mm = 1120 mm² -200mm