Design a decoder which selects the register files of a processor where it has registers from R0 to R15. Assume a 8-bit data word 11011001 is stored in memory. Using an appropriate technique determine the error check bits that would be stored in memory along with the data word. During memory read operation. a LSB (Least Significant Bit) gets modified. Explain how does the technique correct the error? User did not upload files for this question

Design a decoder which selects the register files of a processor where it has registers from R0 to R15. Assume a 8-bit data word 11011001 is stored in memory. Using an appropriate technique determine the error check bits that would be stored in memory along with the data word. During memory read operation. a LSB (Least Significant Bit) gets modified. Explain how does the technique correct the error? User did not upload files for this question

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter8: Data And Network Communication Technology

Section: Chapter Questions

Problem 41VE

See similar textbooks

Similar questions

I am writing in MIPS using the MARS simulator. This is the code I have so far. Can someone help explain how to know how to store the input for the index input into the desired index and then how to print each index?
For the instruction (0x6479), select all data paths that are used from the beginning of the Decode Instruction phase through the end of the Store Result phase. FYI: Be certain; Canvas deducts points for incorrect choices. OL tol OH to J OK to N OL to E OH to F OM to B OC to N OH to L A to F ON to O OM to N O to M
For the 1-byte hexadecimal number OXAB that is stored in a register, only the lower nibble must be set without affecting the higher one. Write down the binary equivalent of the number, the binary bitmask, and the logical operation for solving the task.
LIST P = 16F877AUsing INCLUDE "P16F877A.INC" and PWM (Pulse Width Modulation), write the microprocessor code that enables the fan to operate at 80% if the button on the 5th bit is pressed, and 30% if the button on the third bit is pressed.
D-Latch is a simple clocked memory element in which the output is equal to the stored state inside the element. In D-Latch the state is changed whenever the appropriate inputs change and the clock is asserted. A D-Latch has two inputs and two outputs. The inputs are the data value to be stored and a clock signal that indicates when the latch should read the value on the data input and store it. The outputs are simply the value of the internal state and its complement. When the clock input is asserted, the latch is said to be open, and the value of the output becomes the value of the data input. When the clock input is de-asserted, the latch is said to be closed, and the value of the output is whatever value was stored the last time the latch was open. What is the difference between DFF and D-Latch? Can one chip be used for constructing the other? Explain.
Answer the given question with a proper explanation and step-by-step solution. Use MPLAB to write an asemply program to multipy two numbers (11111001) and (11111001). Then save the product in file reisters 0x50 and 0x51. Return a snapshot of your code, the SFR memory view showing the register used to store the multiplication, the file register view showing the product value.
Sim8085 Three 8-bit numbers are stored at locations 1000H, 1001, 1002H in the memory, write an 8085 program to add the three numbers and store the result at the location 1004H in the memory. Attach assembler output and memory view. Given: Sum of the numbers is also an 8-bit number.
Question 4: There is an application that requires the hardware: an Intel 8031, a Program ROM of 8Kx8, a Data ROM of 4Kx8 for look-up tables, TWO Data RAMs of 8Kx8. The memory map of the design should be: Program ROM should start at address 0000μ. Then, the Data ROM should come above the Program ROM. Finally the Data RAMs must go to the top of the memory map. There should be no gaps between the memory addresses of the external ROMs or RAMS. A. Using logic gates, draw the pin connections of the design. Label your diagram fully. B. Calculate the address space of the ROMs and RAMs of your design. C. Show the design's address space on a memory map, starting with 0000μ at the bottom and FFFFH at the top.
The write operation in Dynamic Random Access Memory (DRAM) is using a voltage signal to represent bit 0 and bit 1. The high voltage represent bit 1 and low voltage represent bit 0? O a. false O b. True
In our implemented register file, it is limited to writing only one data at a time. However, if there is a need to simultaneously record two separate data sets, what should be done?
There is an application that requires the following hardware: an Intel 8031, a Program ROM of 8Kx8, a Data ROM of 4Kx8 for look-up tables and a Data RAMs of 8Kx8. The memory map of the design: Program ROM should start at address 0000H. Then, the Data ROM should come above the Program ROM. Finally the Data RAM must go to the top of the memory map. There should be no gaps between the memory addresses of the external ROMs. Show the design’s address space on a memory map, starting with 0000H at the bottom and FFFFH at the top.
There is an application that requires the following hardware: an Intel 8031, a Program ROM of 8Kx8, a Data ROM of 4Kx8 for look-up tables and a Data RAMs of 8Kx8. The memory map of the design: Program ROM should start at address 0000H. Then, the Data ROM should come above the Program ROM. Finally the Data RAM must go to the top of the memory map. There should be no gaps between the memory addresses of the external ROMs. Calculate the address space of the ROMs and RAMs of your design.