Derive the governing equation of motion for the rocker-arm valve assembly shown below. Assume "small" motions. The quantity Jo is the mass moment of inertia about point O of the rocker arm of length (a + b), k is the stiffness of the linear spring that is fixed at one end, c is the damping coefficient of the linear damper, and M is the external moment imposed by the cam on the system. This moment is produced by the contact force generated by the cam at the end of the rocker arm.

Derive the governing equation of motion for the rocker-arm valve assembly shown below. Assume "small" motions. The quantity Jo is the mass moment of inertia about point O of the rocker arm of length (a + b), k is the stiffness of the linear spring that is fixed at one end, c is the damping coefficient of the linear damper, and M is the external moment imposed by the cam on the system. This moment is produced by the contact force generated by the cam at the end of the rocker arm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Damped Oscillatory Motion The setup consists of a mass m and a mass ", connected by a massless string of length { via a massless pulley. There is no friction between the string and the pulley. Mass m/2 is connected to a spring (spring constant k) and to a damper, damping constant b. Write down the equation of motion for the mass m. Use the coordinate x, with x = 0 being the equilibrium position of the system. Question т m/2] k b
Clear selectior A mass-spring system oscillates on a frictionless horizontal surface in simple harmonic motion with an amplitude A = 0.1 m. At what position (x = ?) would the kinetic energy of the system be equal to three times its elastic potential energy (K = 3U)? %3D At x = +0.05 m At x = +0.04 m At x = +0.025 m At x = +0.08m At x = +0.1 m A traveling wave on a taut
QUESTION 3. Consider the mass-spring oscillator without friction: y" + y = 0. Suppose we add a force x(t) which corresponds to a push (to the left) of the mass as it oscillates. We will suppose the push is described by the function x(t) = -u(t – 2n) + u(t – (2n + a)) for some a > 2n which we are allowed to vary. (A small a will correspond to a short duration push and a large a to a long duration push). Here, u(t) is the unit step function. We are interested in solving the initial value problem y" + y = x(t), y(0) = 1, y'(0) = 0.
0.5 m, k = 500 N/m, and k = 40 N.m/rad, In the system shown, m = 10 kg, r = 0.3 m, Ko where ko is the radius of gyration of the pulley about point 0. There is no slippage between the cord and the pulley. Replace the system with an equivalent { a) torsional spring and mass moment of inertia at point 0, and b) translational mass and spring at point A. т, Ко kt А k m ww
Rotor Hub Low-speed shaft Gearbox J1 ktl - High-speed shaft k,2 Nacelle 02 Tower -Generator J2 Figure Q2 Blade Blade
1- Please, Derive Equation of Motion for the 2DOF system with Harmonic force due to Shaker. Note: I want EOM in Matrices form to get Natural frequencies and Mode shapes + Steady-State Response of Spring-Mass System
* F2 # 3 E Problem 4. EOM Derivation Derive the equation of motion for the following system: We want to measure the spin rate w of the rotating shaft of a turbine. To do it we push a small mass m against the end of the shaft. The shaft makes friction contact with the drag cup mounted on the mass. The frictional torque is b (w). Assume that the rotational spring torque is ke and that the moment of inertia of mass m is J. J Rotating Shaft F3 @ $ 4 R b J, m Drag Cup F4 Q Search % 5 F5 T 0 Wall * A 6 F6 Y 2 * F7 & 7 PrtScn U F8 4 8 Home 6. F9 9 End F10 Po 0
+ b 3. A tuning fork is an example of a "resonant system", that is, one that has a low damping ratio. A model of a (half) tuning fork is rod of mass m with air drag modeled as a damper connected approximately at its middle, and a torsional spring at the base of the cantilever. Assume the cantilever rotates back and forth about its pivot by a small angle o. Because other forces are much larger, you can reasonably neglect the effect of gravity in this model. The moment of inertia of a cantilevered beam pinned at one end is equal to ml2, where I is its length. (a) What is the natural frequency of this system if m= 0.1 kg and k = 2548 Nm/rad, and 1 = 0.1 m. Please give the value in rad/s and Hz. (b) Find an upper bound on the damping coefficient b that insures that the damping ratio of the tuning fork is no greater than = 0.01. (c) For this damping ratio, what is the damped natural frequency of the system? (d) For this damping ratio, what is the decay rate (the size of the exponent…
Question 1 A sketch of a valve and rocker arm system for an internal combustion engine is give in below figure. Model the system as a pendulum attached to a spring and a mass. Determine the equations of motion and calculate the natural frequency in rad/s. The mass moment of inertia of the rocker arm about its pivot point j=0.46, the stiffness of the valve springspring k=420 , the distance from pivot to spring I= 0.98 m, and the mass of the valve m=3.2 kg. Ignore the mass of the spring and the oil effect. Rocker arm Follower k Valve spring LOil Cam m Valve
Consider the system shown below. Answer Questions 6-11 based on this figure. How many degrees-of-freedom does the system shown below has? The two pulleys have the identical mass, radius, and the moment of inertia. т, 1, R k т, 1, R Variables x: vertical position of the moving pulley 8: rotation of the moving pulley p: rotation of the fixed pulley m: pulley mass R: pulley radius I: mass moment of the pulley about its own center of mass. k: spring stiffness T: cable tension Assumptions 1. x = 0, 0 = 0, and o = 0 when the spring is undeformed. 2. The cables and springs have negligible mass. 3. There is no slip between the pulley and the cable. 4. Only two-dimensional planar motion is allowed.
4. The system has three axes or three levels, only the motor is connected on the first axis. At the end of axis 1 is a gear (N₁) connected to a gear (N₂), the left gear of Axis 2. The right gear of axis 2 (N3) is connected to the gear (N4), the left gear of Axis 3. At Axis 3 has an inertia (Ja) of 8 kg-m² and a damper of 32 N-m-s/rad. Draw the system and find the Transfer function that relates the voltage at the motor to the angular displacement at JA. Additional information: Gear N₁ has 10 teeth and an inertia of 1.5 kg-m² Gear N₂ has 20 teeth and an inertia of 2 kg-m² Gear N3 has 10 teeth and an inertia of 2 kg-m² Gear N4 has 20 teeth
For the shown spring-mass-damper system. Let m =1 kg, b = 2 N.s/m, k = 2 N/m and f(t) = sin2t N. (a) Write the equation of motion. (b) Find the amplitude of the steady state oscillations. (c) Find the steady state maximum acceleration.