ded tension member is consisting of two channels placed 400mm back to back with flanges turned out. Select a channel for factored tensile of 4RKN using A36 steel and AISC specifications. The member is to be 15m long.
Q: The azimuth from south of the tangent from PC to PI is 223 degrees and Pl to PT is 318 degrees. The ...
A: Given : Azimuth from south of the tangent from PC to PI = 223°Azimuth from south of the tangent from...
Q: onsano Acomposite assembly consisting of a steel [G- 80 GPa] core (2) connected by rigid plates at t...
A:
Q: Determine the limiting moment resisting capacity (as per LSM) of a beam cross- section having width ...
A:
Q: 1. Compute the acceleration of body B, and the tension in each cable supporting each block. WA= 200 ...
A:
Q: . Solve for the following internal forces occurring on the beam loaded as shown below. a. Moment at ...
A:
Q: A car is travelling at 28 m/s when the brakes are suddenly applied and result in a constant decelera...
A: Given data : Initial velocity (U)=28 m/s Constant deceleration (a)=-5 m/s2 Final velocity (V)=0 m/s ...
Q: A solid sphere made of aluminum (SG = 2.7) is suspended in water by a cable. The cable has a tension...
A:
Q: Determine the reactions for the continuous beam shown by the three-moment equation. Draw the shear a...
A:
Q: 3m 9m W2 8m W1 6m
A:
Q: In the figure shown, Given: B =1.3 m/s 0 = 60° Solve for: a) velocity of A (m/s) b) angular velocity...
A: Appreciate if there is detailed work with explanation and finds you helpful for ease of understandin...
Q: A prismatic solid circular rod of diameter dis bent to introduce an offset s = das shown. The rod is...
A: GIven data,
Q: Determine the difference of energy grade line and hydraulic grade line of an open channel with stead...
A: Given data in question Discharge Width Depth To find out Difference between EGL and HGL
Q: 2. The volumes of water fiowing in a stream in each of the successive months are given below: 2.80, ...
A:
Q: At the instant when u = 90°, the motor on the car wash sprayer in Figure P7.38 rotates counter-clock...
A: We have to determine the value of angular velocity and angular acceleration of the nozzle arm by rel...
Q: A 300 mm diameter test well penetrates 27 m below the static water table. After 24 hours of pumping ...
A:
Q: - Stabilized soil brick is made from clay mixed with a small percentage of some stabilized materials...
A:
Q: A uniform load of 2000 N/m, 5 m Long crosses a girder of 20m span from left to right. Calculate the ...
A:
Q: An unconfined compression test was conducted on a sample of clay having diameter of 50 mm. The failu...
A: Given data in question Load Diameter Clay Unconfined compressive strength test To find out Cohesi...
Q: X Your answer is incorrect. The copper pipe [G - 7,000 ksi] has an outside diameter of 3.250 in. and...
A:
Q: Ex2: An embankment shown in the figure is constructed. compute the vertical stress increment under P...
A: Calculating q q=γ1Hq = 19.2x6q = 115.2 kN/m2 σz = ql5σz=qπB1+B2B1α1+α2-B2B1α2 Here, B1=10B2=6...
Q: The 55-kg crate shown in the figure rests on a horizontal surface for which the coefficient of kinet...
A:
Q: A cubic meter water is subjected to a pressure increase of 20 MPA. If the bulk modulus of elasticity...
A: We know Bulk modulus=Change in pressureChange in volume
Q: 1. The frame shown in Fig. P-348 is supported in pivots at A and B. Each member weighs 5 kN/m. Compu...
A: Given data, Member weight = 5 kN /m Load = 200 kN To find out the horizontal and vertical reactio...
Q: An unspecified pure bending moment is used to bend an aluminium rod of radius 2.5 mm elastically int...
A:
Q: a) What are the four heat fluxes (Q) across the sea surface? b) complete the labels for all curves b...
A: Four heat fluxes: Short-wave solar radiation, Sensible heat flux, latent heat flux, long-wave radia...
Q: 1. For the beam and loading shown, (a) draw the shear and bending-moment diagrams, (b) determine the...
A:
Q: If 1,688 cu.m. (in place at natural density) of dense clay (35 percent swell) needs to be hauled awa...
A:
Q: SITUATION: A footing, 2m x 3m in plan and 0.50m thick, is designed to support a 0.60m square column....
A:
Q: A 25mm diameter pin at B connects the crank mechanism loaded as shown in the figure. 500KN 200mm 100...
A:
Q: A beam of flexural rigidity EI is fixed at A and supported by a linear spring of stiffness k = EI at...
A: Given data, Flexural rigidity =EI Stiffness of spring= To find the compressive force developed in t...
Q: A sample of saturated clay had a volume of 97 cm3 and a mass of 0.202 kg. When completely dried the ...
A: Shrinkage limt is :SL=MC-V1-V2Wdryρw
Q: 103. What is the quantity (Sq.m) of plastering required for the 6m length of wall which is 4m high a...
A: Area of plastering and it’s depth have been given and it has been asked to determine volume of plast...
Q: A finite slope has a height of 9m and it makes an angle of 30 degrees with the horizontal. The unit ...
A: To Determine The developed frictional force along the failure plane.
Q: The solid 1.55-in.-diameter rod is subjected to a uniform axial distributed loading along its length...
A:
Q: 7.23. The construction cost of the dam at a given site for different heights of the dam and the corr...
A: Step 1: To determine the most economical height of the dam, there are six sets of reading. The curve...
Q: The sanding-drum mandrel shown in the figure is made for usewith a hand drill. The mandrel is made f...
A:
Q: a) For the fixed steel beam shown in Figure 1, use the double-integration method, i) determine the r...
A:
Q: 5. The force in member BD A. - 48.54 KN B. - 43.51 KN C. - 38.38 KN D. - 56.89 KN 6. The force in me...
A: ###Determination of forces in member BD,AD,CD ####
Q: Given the clevis shown, P=25KN. If the shearing stress is limited to 60 MPa, what is the diameter of...
A:
Q: 500KN 200mm 100mm What is the value of force P in KN?
A:
Q: Situation: The results of a consolidated drained triaxial shear test conducted on a consolidated cla...
A:
Q: Given data : Stress=30 N/mm2 Force=2 N Find area
A: Given data : The value of force F=2 N The value of stress σ=30 N/mm2 To find : Area
Q: A laboratory consolidation test on the normally consolidated clay gave the following values: Pressur...
A:
Q: Modulus of elasticity and Poisson's ratio of a material are 2-1 x 105 N/mm2 and 0-25 respectively. W...
A:
Q: Two converging tangents have azimuth from the south of 300deg and 900deg respectively, while that of...
A: Data given: Two converging tangents have azimuth of 300° and 90° respectively Common tangent = 320° ...
Q: For a simply supported prestressed concrete bearn, compute the stress in the top fiber at midspan du...
A:
Q: A simply supported beam AB supports a trapezoidally distributed load (see figure). *Inserted Photo* ...
A:
Q: A flagpole 16 m high has the shape of a cylinder 100 mm in diameter. The air temperature is 30°C and...
A:
Q: SITUATION: In order to determine the volume and the specific gravity of a stone that weighs 45 kg in...
A: Given: Mass of stone in air = 45 kg Mass of stone in water = 30 kg Calculate the volume and specific...
Q: Explain the difference between sieve analysis between coarse and fine aggregates. Discuss the standa...
A: Scope Fine Aggregate (FA) Coarse Aggregate (CA) Definition Fine aggregates are the small size and...
A welded tension member is consisting of two channels placed 400mm back to back with flanges turned out. Select a channel for factored tensile of 4RKN using A36 steel and AISC specifications.
The member is to be 15m long.
Take R= 433.5 Factored design load= R*4
Step by step
Solved in 2 steps
- A PL40 mm X 250 mm (smaller member) is connected to a gusset plate (bigger member) as shown. The diameter of the holes are 25 mm. The pitch and gage of the holes are 50 mm and 75 mm, respectively. The yield strength of the steel is 260 MPa while the ultimate tensile strength of the steel is 400 MPa. Determine the design (LRFD) tensile strength of the tension member in kN. Neglect block shear. H G P P D B F C A EA PL40 mm X 250 mm (smaller member) is connected to a gusset plate (bigger member) as shown. The diameter of the holes are 25 mm. The pitch and gage of the holes are 50 mm and 75 mm, respectively. The yield strength of the steel is 260 MPa while the ultimate tensile strength of the steel is 400 MPa. Determine the design (LRFD) tensile strength of the tension member in kN. Neglect block shear. H FO E. • D A ВSix rivets are used in the connection shown in the figure. If both P=50KN, what is the minimum diameter rivet is necessary so as not exceed the 70MPa allow shearing stress? What thickness of plate is required so as not exceed a bearing stress of 140MPA? p= 50 80 mm 80 mm 100 mm
- The steel tie bar shown is to be designed to carry a tension force of magnitude P = 120KN when bolted between double brackets at A and B. The bar will be fabricated from 20-mm-thick plate stock. For the grade of steel to be used, the maximum allowable stresses are: o = 180 MPa, t = 120 MPa, op = 380 MPa. Design the tie bar by determining the required values of: a. the diameter d of the bolt, b. the dimension b at each end of the bar, c. the dimension h of the bar.2) Find the axial stresses of menbers FD, GD, GE State if it is tensile or Compressive. 4M 3M A LE 3m G 20 RN Go KNThe wall bracket show below carries a load of P Kip. the allowable tensile in the eye bar is 20 ksi, and the allowable shear stress in the pin is 12 ksi. Select: a) The diameter of the eye bard b) the diameter of the pin at A which is double shear c) the diameter of the pin at B which is single One eye-bar 6 ft P kip 4 ft
- A double-row butt joint is used as a connection. It is made up of two 210mm by 12mm cover plates and 210 mm by 20 mm main plate. The plates are to be connected by 22 mm diameter rivets. The allowable stresses are 65 MPa for shear, 83 MPa for tension, and 135 MPa for bearing. Assume that each hole is 3 mm larger than the rivet diameter. Calculate the largest value for P that can be applied without exceeding the allowable stress for tension. o a. 418.3 kN b. 330.8 kN c. 348.6 kN (Ctrl) o d. 265.6 kN PeSelect all zero-force members in the truss shown below. Check the box for zero- force members 3 m 3 m 12 m, 8 @ 1.5 m DE O LK ЕР O HF O BC BM EF OM CD BN LO O DK FI O coDetermine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
- A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0.a) Determine the design tensile strength of the section based on yielding of the gross area.b) Determine the critical net area of the connection shown.Civil Engineering A welded tension member is consisting of two channels placed 400mm back to back with flanges turned out. Select a channel for factored tensile of 4RKN using A36 steel and AISC specifications. The member is to be 15m long. Take R: 433.5A PL 38 X 6 tension member is welded to a gusset plate as shown. The steel is A36 (Fy = 36ksi, Fu = 58ksi). a. The design strength, Pu based on gross area b. The design strength, Pu based on effective area PL % x 6 3/8" 6" Cross Sectional area of PL3/8x6 a) Blank 1 b) Blank 2 Blank 1 Add your answer Blank 2 Add your answer