DE 20 60

Q: Please answer this numerical

A: The data corresponding to 500 m3/h flow rate from the graph is

Q: Circle your answer please

A: Data given - M = 44 kg  dAB = 8 mm 

Q: Please answer the first 3 parts. ASAP

A: Combined cogeneration gas turbine and steam turbine plant In this plant gas turbine and steam turbin...

Q: A Wind Energy Conversion System with the following data: Downward wind velocity:8 m/s Upward wind ve...

A:

Q: - once answered correctly will UPVOTE!!

A: The relative velocity is the velocity of point A is with respect to point B. vA/B=vA-vB VA/B is the ...

Q: Determine the forces on each member of the truss considering that a cylinder with a weight of 83 N i...

A:

Q: A group of kinematic pairs which are connected together in order to provide a useful motion between ...

A: Option (b) kinematic chain. is correct option

Q: A rod of length L = 2 m slides against a wall as shown in Figure. The velocity of point A is given =...

A:

Q: The mass damper spring system shown in the figure;a) Draw the free body diagramb) Extract the equati...

A:

Q: the distinction between closed conduits and open channels

A: Channels are the arrangements made for the fluid flow to occur. The flow of fluid in a pipe mainly o...

Q: The resultant of the two forces F =766 N and P = 1458 N is a vertical force directed upward. If the ...

A:

Q: (machine dynamıc) In a damped free-vibrating mass spring damper system, the mass is 1.9kg, the sprin...

A: m=1.9 kg,k=7550 N/mAmplitude for 1st cycle, x1=0.35 cmAmplitude for 5th cycle, x5=0.07 cm

Q: Determine the heat flux through the composite walls as shown in Figure. The frontal area (normal to ...

A:

Q: (a). Mention the types of maintenance. Define breakdown maintenance. b). Draw the diagram and explai...

A: Maintenance  In general, maintenance may be described as attempts to maintain a machine's condition ...

Q: Reduce the given loading system to a force-couple system at point A. Then determine the distance x t...

A: Given,   

Q: 20. A Wind Generator with the following data is installed at a wind site. Upward wind velocity: 14 m...

A:

Q: Cavitation occurs when: the pressure of the fluid drops equal to the vapor pressure of that fluid th...

A: Given: Cavitation works when:

Q: Q3. Obtain an equation for the temperature distribution (x) in the nuclear fuel as shown in figure.2...

A: Given: The nuclear fuel with the heat transfer is shown below: Assume: The heat transfer is one-dim...

Q: In the Figure, atmospheric pressure is 14.80 psia; the gage reading at A is 3.7 psi; the vapor press...

A: Pressure measurement is the analysis of an applied force by a fluid (liquid or gas) on a surface. Pr...

Q: A copper (m = 50g, c = 0.385 J/gdegC, temp = 85degC) is placed beside %3D an insulator (m = 100g, c ...

A:

Q: The strength of a 10% moist wood material in the direction parallel to the fibers was determined as ...

A:

Q: Draw the shear and moment diagram for Beams ACD and DE that are supported atA, C,and E, and are join...

A: Shear force diagram represents shear force at every section of the beam.. Shear force at any particu...

Q: QUESTION 6 In a free cylindrical vortex flow, at a point in the fluid at a radius of 0.20 m and at a...

A: A free vortex flow is one in which the fluid mass rotates without being influenced by an external fo...

Q: Theory of machine

A: Solution :-  Given data :- vAO = 130 rpm ωAO = 2π × 13060= 133π Since the length of crank OA = 100 m...

Q: A jet of water having a velocity of 10 m/s and a flow rate 60 L/s is deflected through a right angle...

A: Jet is water that coming out from the nozzle at a very high speed. And the expression of the force t...

Q: Please answer these 2 questions

A: Q.1       Given:                Pi=130 MW               Qtu=100 MW    Qcond=150 MW

Q: need solution

A: For solution refer below images.

Q: Which one of following devices is used to control the movement of parts of the mechanism? a. Bel...

A: Belt drive and gear dive, transmit the torque in the mechanism sliding pair gives to and fro motion ...

Q: BRI, A semicircle of 90 mm radies i css out froma wapezium as shown in Fig 6.23 Find the position of...

A: Centre of Gravity  The gravitational center, in physics, is the imaginary location of a body of matt...

Q: Correct the following false statements: 1) The systematic errors occur in the output readings of a m...

A: Correct the following false statements:1) The systematic errors occur in the output readings of a me...

Q: A Brayton cycle with an air inlet temperature of 17 °C has a pressure ratio of 16. While the cycle p...

A:

Q: It's a complete question. Need help asap.

A: As perhonor code and answering guidelines I can answer 1st 3 subparts at a time.If you want other pl...

Q: In a Diesel engineRequired to answer. Single choice. OPTIONS: 1.Only spark plug is used 2.Spark p...

A: In a Diesel engine Answer: 3) None

Q: Sketch the missing view and the isometric view -2X 08 -20- -20- 12 5 30 20

A: the missing view is the bottom view 

Q: I only need help with letter (c).   A window-mounted air conditioner supplies 19 m3/min of air at 15...

A:

Q: The motion is partly sliding and turning in which type of kinematic pair. a. Lower pair. b. P...

A: Kinematic pair is the relative motion between the two links and the motion is successfully constrain...

Q: Identify the number of instantaneous centres present in a mechanism which has 4 links. a. 18 b...

A: Given, no. of links, n=4 So, No. of Instantaneous centres, N = n(n-1)/2 = 4(4-1)/2= 6

Q: Draw the shear and moment diagram for Beams ACD and DE that are supported atA, C,and E, and are join...

A: Shear force diagram represents shear force at every section of the beam.. Shear force at any particu...

Q: 2 Sall Zal e Can the rudder be manually trimmed with the autopilot engaged? * The figure below is no...

A: The rudder controls movement of the aircraft about its vertical axis .Rudder trim is done to keep th...

Q: Which one of the transducer is used for the position sensing? LVDT Thermistor RTD ...

A:

Q: Q: A single plate clutch, effective on both sides, is required to transmit 20 kW at 2500 rpm. Determ...

A: Clutch : It is a device used in transmission of  power. The clutch is used to engage & disengage...

Q: Initial condition: P = 0.7 MPax = 96 %Process: ThrottlingFinal condition: P = 0.35 MPaRequired: Δs

A: Solution:

Q: qq5 Which of the following gate will have high output if at least any one input is high ?. a. NA...

A: Given Statement:  Which of the following gate will have high output if at least any one input is hig...

Q: Q:In Figure, two blocks are connected by a solid strut attached to each block by a pin. If block B w...

A: This question is related to the static equilibrium problem. In this question, the static friction fo...

Q: Design the nozzle of a fuel injector, which has to expand 2.5 g/s of methane (R = 518 J/kgK; k=1.31)...

A: Nozzle is a device which having varying in cross section, in which pressure is reduced by expansion....

Q: State the disadvantages of hydraulic transmission systems.

A:  Hydraulic transmission system- This system is sealed and transmit power by using the pressure of fl...

Q: The 7 Ib particle is subjected to the action of its weight and forces F, {2i + 6j 2tk} lb. F2 = {t°i...

A:

Q: An open horizontal tank 3 m high, 3.5 m wide and 6 m long is initially filled at 2 m of water. a. De...

A:

Q: Mechanics of Materials: The anchor beam AB is of uniform cross-section and carries a load P at the f...

A:

Q: Hello, Can you please help me in finding the answers for letter a,b,c, and d.  :) Thank you very muc...

A:

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.