Data of a closed traverse are as follows: Compute the distance of line (5-1) a. 206.92 m b. 374.97 m c. 267.88 m d. 423.54 m

Q: H |B 40 kN 40 kN - 4 at 3 m = 12 m -

A:

Q: A 25 m deep bored pile has a shaft of 1 m diameter and enlarged base of 2.5 m diameter in the lower ...

A:

Q: A rigid bar AB is pinned at end A and issupported by a wire CD and loaded by a force P atend B (see ...

A: Given:- E = 210 GPa σY =820 MPa L =1.0 m diameter is d =3 mm To find:- (a) Assuming n = 0.2, calcula...

Q: 7. In the clevis shown in Fig. 1-11b, find the minimum bolt diameter and the minimum thickness of ea...

A:

Q: 4. Find all reactions and member forces for the truss. E= 30000 ksi. Partial answer: Fed = S5.29 k (...

A: Given Data -

Q: For a minor principle stress of 50 kPa, what is the maximum value possible for the major principal s...

A:

Q: The cross-sectional dimensions of a beam are shown in the figure. (a) If the bending stress at point...

A: Given, Bending stress at point k =35 MPa b=85 d=4 mm

Q: 9. Calculate the increase in stress for each segment of the compound bar shown. If the temperature i...

A: Given:- The cross-sectional area of the aluminum bar = Aal = 2 in2  The modulus of elasticity of the...

Q: A 25 m deep bored pile has a shaft of 1 m diameter and enlarged base of 2.5 m diameter in the lower ...

A: Length of bored pipe = 25m Shaft Diameter = 1m  Diameter of enlarged portion = 2.5 m  Area of enlarg...

Q: 185 lb C B D -8 ft- 8 ft-

A:

Q: The bar AB is attached to aluminum and steel rods, horizontal before the load P is applied. Find the...

A:

Q: Ground surface Contring Layer Confined aquifer ha K mid Bedrock Determine Q for aquifer above if im ...

A:

Q: parabolic sag curve has tangent grades of –1.2% and +0.60%. The total allowable change of grades per...

A:

Q: When soil water potential in a sandy loam soil goes from -0.1 to -10 bars, the height of an equivale...

A: Given soil water potential in a sandy loam soil goes from - 0.1 to - 10 bars. Height of an equivalen...

Q: 1- Using your calculator, calculate v0. 03 + 1.027, then correct to two significant figures 2- Conve...

A:

Q: The pin-connected rigid rods AB and BC are inclined at 0 the force P is applied, 0 becomes 32°. Dete...

A:

Q: 15 k 15 ft B 12 k 24 k 24 k 24 k 24 k 6 at 20 ft = 120 ft- FIG. P3.17

A:

Q: Exercises Minimum Fotential Energy / Minimum Work For each of the beams shown, use EPM/T. Min. to de...

A:

Q: Determine the available axial compressive strength by each of the following methods: a. Use AISC Equ...

A: Given Data -

Q: Problem A cantilever beam AB supports a couple and a concentrated load, as shown in the Figure. Draw...

A:

Q: round surface to a depth of 20 feet below the ground surface. The clay has a wat ontent of 35%, S = ...

A: Given:- depth=10feet deopped depth=20feet water content=35% S=100% Gs=2.75 To find:- vertical normal...

Q: how does your computations go when for example all needed info are derived as usual and THE FLOW IS ...

A:

Q: A body of mass 3 kg is under a force, which causes a displacement in the body which is given by s = ...

A:

Q: AT- section is the cross section of a loaded beam as shown.

A: Given: Simply supported beam with an overhang. The beam carries a uniformly varying load.  To determ...

Q: find the maximum shear

A: Solution: Given data: Dia = 2 in Angle of twist = 8 deg W know that maximum shear stress formula Tma...

Q: 40R 40k 4) Determine the member forces in bars: AC, CD, DF & CF. 20K 144 30K 14 A 30K 14

A: Taking moment about point D FAC X 20  = 40 X 20 - 20 X 14  FAC = 10 kn ( Compressive)

Q: 7. The lower ends of the three bars in Fig. P-238 are at the same level before the uniform rigid blo...

A:

Q: Compute the bearing of line BC. Compute the distance of line DE. Compute the area of the lot using D...

A:

Q: In a watershed four non-recording raingauges have been installed to record rainfall data. The annual...

A:

Q: Questión 2 Refer to Appendix A for tables and equations to be used. Use the CNCI method. You are giv...

A: As per the given information we have calculate the following things which are:  amount of water  am...

Q: A steel plate of dimensions 2.5 X1.5 X 0.08 mand weighing 23.1 kN is hoisted by steel cables withlen...

A: Given:-  2.5 X1.5 X 0.08 mweighing 23.1 kN L1 = 3.2 m and L2 = 3.9 m  To find:-  T1 and T2,  average...

Q: 2. A simple curve has a central angle of (20 +3) and a degree of curve of 5º. a. What is the value o...

A: step 1-

Q: Knowing that the allowable normal stress for the steel used is 24 ksi, select the most economical wi...

A: The values and diagram given in the question are as follows: Allowable normal stress(σ)=24 ksi

Q: kPa, what is the maxim to exceed 40 kPa?

A:

Q: 2: Determine the area required for a new landfill site with a projected life of 20 years for a popul...

A:

Q: Data on a traffic accident record on a certain intersection for the past 4 years has an accident rat...

A:

Q: THIS IS A SIMPLE BEAM WITH A SPAN LENGTH, L = 5M 2M 3M 5M R, R2 1. DRAW THE INFLUENCE LINES ALONG WI...

A:

Q: Compute for the Shear and Moment Equation each segment (kindly include the FBD). Compute the Reactio...

A:

Q: For a minor principle stress of 50 kPa, what is the maximum value possible for the major principal s...

A: Given that -

Q: A sand with a void ratio of 1.0 and a Gs= 2.65 is assumed dry above the GWT at 3m. What is the effec...

A:

Q: a depth of 10 feet in a saturated clay layer if the water table is dropped from surface to a depth o...

A: Given:- depth=10feet dropped depth=20feet S=100% Gs=2.75 water content=35% To find:- total vertical ...

Q: Determine the largest load P that can be applied to the frame

A:

Q: 3. A bronze bar is fastened between a steel bar and an aluminum bar as shown in Fig. P211. Axial loa...

A: We have to determine the value of largest value of P that will not exceed an overall deformation of ...

Q: 3. An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure. ...

A: The free body diagram of the rod is given:

Q: V el. 260.3 ft alig h SH 100 olig a Scale (ft) Reservoir si 1ote Concrete spillway Sheet pile el. 18...

A: Computing for the top figure                                          From the above figure, given d...

Q: GIVEN: diameter of sewer pipe = 1.8m Depth of water = 1.6m Q = 2.5m3/s Compute the velocity. Use 3...

A: Diameter of pipe, D =1.8mThe depth of water, d =1.6mThe discharge in pipe, Q =2.5 m3s  

Q: A uniform concrete slab of total weight W is to be attached, as shown in Fig. P- 215, to two rods wh...

A: GIven: Weight of concrete slab =  W, Steel and aluminum rods supports the slab as shown. We need to ...

Q: Determine the resulting surface area when the curve x1.5 is rotated about the y-axis in the interval...

A:

Q: Determine the critical for design bending moment Mmax for the beam below. Write your answer in a box...

A:

Q: 4m 4 m 4 m- 4 m 4 m--4 m 5 kN 3 kN D 3 kN E 10 m B F K J H 6 m 6 m 6 m 6 m

A: Section method is generally applicable when forces are required only in few members. Cut these membe...

Traverse Survey

Traverse surveying is a popular method of surveying. Traversing is that type of survey where several connected survey lines form a framework and the directions and lengths of the survey lines are measured with the help of a tool to measure angles and tape or chain respectively. Traverse networks involve placing survey stations in a queue or trail and using pre-tested points as a basis for looking at the next point. This type of surveying is different from Tacheometric surveying, where only angles are measured and the process of chaining is reduced.