D1 Vsecondary Vfiltered D2 V1 sine Rload I 120 VAC @ 60 Hz D3 10:1 - D4 Figure 1: Bridge Rectifier Voltage Regulator Circuit The filter capacitor C, is recharged on every half-cycle of Vsecondary. Given: Rioga = 100 N VDiodes = 0.7 V Vi is given in RMS What is the minimum value of capacitor C, required such that V,utered does not drop below 8 V? iw.

D1 Vsecondary Vfiltered D2 V1 sine Rload I 120 VAC @ 60 Hz D3 10:1 - D4 Figure 1: Bridge Rectifier Voltage Regulator Circuit The filter capacitor C, is recharged on every half-cycle of Vsecondary. Given: Rioga = 100 N VDiodes = 0.7 V Vi is given in RMS What is the minimum value of capacitor C, required such that V,utered does not drop below 8 V? iw.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A Capacitor filter is used at the output across the load in order to minimize the ripple factor of the output voltage. The expressions of the average output voltage Vpc and the output AC component VAc are given below. If R = 1k2 and the single phase bridge rectifier supplied from a 120V - 50 Hz sinusoidal source, then the capacitor value that will maintain the amount of the output ripples to less than 4% would be equal to: VDC = Vm(4FRC – 1)/4ƒRC) VAC = Vm/(4/2ƒRC) Select one: O a. 63.39uF O b. 33.2uF O c. 93.39UF O d. 126.2uF TOSHIBA
Design of a DC-DC Converter. The Circuit Below shows a basic Buck-Boost Converter with a highly inductive Load. With a Deliberate mistake in the configuration of the Circuit Connection. The Value of L1 is 22mH, C1 is 10uF, R1 is 220 and L2 is 10mH. The circuit operates with a switching frequency of 20KHZ. The Duty cycle of the Clock signal V2 is given by the function below: ( 17 ) х0.2 Duty Cycle, k = 0. 55 + 100 Your Unique Duty Cycle = %3D Buck-Boost Converter Q1 IRG4BC10U D1 R1 222 1N4009 C1 LV1 12V L1 22mH 10µF L2 10mH a) Find the mistake in the configuration of the circuit and correct the connection error.
Determine the peak to peak ripple voltage and the ripple factor for a bridge rectifire using capacitor input filter. The load resistance is 2 kn while the d.c voltage across the loadis 12 V. Assume supply frequency to be 50 Hz and ideal diodes. The capacitor of 100 µFis used in the filter circute.
A buck regulator has Vsource 15 V. The average output voltage required is Vo=6 V with peak-to-peak ripple input of 10 mV, the switching frequency is 20 kHz and the peak-to-peak ripple of current of the inductor L is 0.6 A. Calculate the duty cycle and the values of Land Crequired.
Question 3 Consider the following cirucit: in + V1 R1 5 PULSE (0 2 1 1 1 1) (Note again the unrealistic diode characteristics.) The input is a ramp: 2.0V- 1.6V- 1.2V- 0.8V- 0.4V- 0.0V- 0.0s 0.2s 0.4s 0.6s 0.8s out .tran 2 .model diode D(Ron=5 Vfwd=1 Roff=1G) V(in) D1 diode 1.0s 1.2s 1.4s 1.6s 1.8s 2.0s The output voltage is similar to the input voltage, except that it breaks at a certain voltage and reaches a different final value. Find the break voltage and the final value of the output.
4. An RC filter stage (R = 33 0, C = 120 HF) is used to filter a signal of 24 V dc with 2 V rms operating from a full wave rectifier. Calculate the percentage ripple at the output of the RC Section for a 100-mA load. Also calculate the ripple of the filtered signal applied to the RC stage. *****END*****
Design the Clipper-Clamper circuit to perform the output waveform shown in figure below. GaAs Diode GaAs Diode Vo f=1 kHz. 3 V + -3V Clipper Clamper -13 V -10 V
• Design a classical rectifier to deliver 100W into a resistive load from a 120V, 60HZ mains. ac Quantify the effect for different values of filter capacitance on: >average output voltage >output voltage ripple >Input current shape, harmonic content and THD
(b) Discuss the impact of connecting a large capacitor filter across the load in Figure Q1(ii). Use appropriate waveform sketch to aid your discussion. + Vp - Us R2 RL Vs ( (i) (ii) Figure Q1. Single phase half bridge rectifier: (i) with a Thyristor (ii) with a Diode
Q2) For the circuit shown in Figure 2, sketch the output voltage (across the load 2.2 KO resistor) and the load current (through the load 2.2 KN resistor). Sketch the diode voltage (across the diode D1) and the diode current (through the diode D1). The input Vi is sinusoidal with maximum amplitude (peak) of 14.1422 V and frequency of 60 Hz. The diode D1 is a Silicon diode. The sketches have to be at least for two cycles of the input. D1 2.2 K2 Vi
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consistingseries connected a resistor and an inductance from a 70.7V (RMS), 50Hz sinusoidal AC source.The firing delay of the thyristor is 90° and the load values are R=10Ω, L=0.1 H. Define the loadcurrent expression and draw the load current by calculating for first two periods. And calculate theaverage values of the load voltage and current.
S-4) The input signal Vin of the clipper circuit given below is a sinusoidal signal of Vp-p = 30V and the wave the form is as given in the figure. a) Plot the output waveform of this circuit in the area given for + and - alternans. b) Calculate the peak values of the output and indicate it on the graph. Note: Diode threshold voltage will be 0.7V