Subject MECHANICS OF MATERIALS AND STRUCTURES Civil Engineering please quickly Table Q1M1(kNm)M2(kNm)w(kN/m) P1(kN) P2(kN)wwwwwwwwwww8181002012Construct the shear force diagram (SFD) and bending moment diagram (BMD) for the beamin Figure Q1 and indicate the important values in the diagrams. The values of the forces andmoments are given in Table Q1. Note that if the value given for any of the force or moment isnegative it means that direction of the force or moment is opposite of the direction given inthe diagram.P1 (kN)P2 (kN)w (kN/m)M2 (kNm)M1 (kNm)Oc2 m3 m2 m2 mFigure Q1

Answered: Image /qna-images/answer/e373af08-526f-4718-8e94-8139a0850e31.jpg

Answered: D STRUCTURES Civil En

Engineering

Civil Engineering

D STRUCTURES Civil En

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q 3. A rigid beam AB is 5.5 m long, hinged at point A and supported by two pipes at C and D as shown in figure 3 below. Pipe 1 at C is of copper has a outer diameter of 120 mm and inner diameter of 100 mm and yield stress of copper is 138 N/mm² Pipe 2 at D is of steel has a outer diameter of 100 mm and inner diameter of 90 mm and yield stress of steel is 250 N/mm2 Calculate the safe load at A if the load factor is 1.66 Pipe 1 Pipe 2 Psafe 2.3 m 2 m C 5.5 m Angle ACE = 0 Figure 3 Angle BDF = 42° Take 0 = 10 Page 7 of 7 PTO
Figure 1 shows a structural beam and Figure 2 the cross section the beam. Additional to all the loadings shown beam AD has a constant clockwise internal moment coming out of the page of 2kN.m. Answer the quesstion in the second picture (the one with figure 2)
A steel strut S serving as a brace for a boat hoist transmits a compressive force P= 57 kN to the deck of a pier as shown in the figure. The strut has a hollow square cross section with wall thickness t = 9 mm and the angle O between the strut and the horizontal is 30°. A pin through the strut transmits the compressive force from the strut to two gussets G that are welded to the base plate B. Four anchor bolts fasten the base plate to the deck. The diameter of the pin is dpin = 16 mm, the thickness of the gussets is tG = 14 mm, the thickness of the base plate is tg = 10 mm, and the diameter of the anchor bolts is dpolt = 10 mm. Determine the bearing stress between the anchor bolts and the base plate in MPa. ROUND OFF TO TWO DECIMAL PLACES. Pin S 16 (a) (b)
As shown in the figure, rod AB is steel and rod BC is an aluminum, are hinged to rigid suppots which are pinned together at B to carry a vertical load P=20kN. Each rod has a cross-sectional area of 400mm^2 and Es=200000Mpa and Ea=70000Mpa. Compute for the deformation of steel and aluminum and for the horizontal and vertical displacements of point B.
PROBLEM 1: The frame shown in the figure is carrying a traingular distributed load. Pins at A and B are forced in single shear while the pin at C is forced in double shear. If the allowable tensile stress of bar BC is 300 MPa and the allowable shear stress of pins is 150MP3; (a) The cross sectional area of BC (b) The required diameters of pins A, B and C as multiples of mm. w = 8 kN/m 6 m 5 m 3 m
STRESSES IN BEAMS Problem 2 The simply supported beam in Fig. (a) has the T-shaped cross section shown. Determine the values and locations of the maximum tensile and compressive bending stresses. 400 lb/ft 1000 lb - 6 in. Į C0.8 in. D A 0.8 in.- 8 in. - 4 ft- Rg = 3400 lb 10 ft R = 1600 lb %3D %3! (a)
The beam has a rectangular cross section and is subjected to the loading shown. Determine the components of stress ox, oy, and Txy at point B. 800 N B 1000 N 15 mm 20 mm 20 mm 15 mm 100 mm 10 mm
The geometry of the truss that you are to analyze is shown below in Figure 1. The load at joint B is at an unknown angle 0 from the horizontal as shown. The following data is known: Three-member simple truss Joint-to-joint length of member AC: Magnitude of force F applied at joint B: A LYX Fixed support at joint A Rolling support (y movement arrested) at joint C 0° ≤ 0 ≤ 360° 30° B Ө 45° F 0.6 meters 550 Newtons с Figure 1: Three bar truss with applied force F at angle 0 counterclockwise from horizontal For a given angle 0 in degrees your task is to determine the tensions in members AB, BC, and AC, as well as reaction forces Ax, Ay, and Cy. The convention used here is that members in compression will have a negative value for their tension, and reaction forces are aligned with the positive x- and y-axes.
W A L A Test beam Strain gauge (a) Unsymmetrical cantilever beam with weight applied at the free end and at the "shear centre", so that there is no torsion induced. b Section A-A Strain gauge 1 Strain gauge 3 Strain gauge 2 B (b) Location of Huggenberger strain gauges a D Referring to the above figure, calculate the location of the centroid, the second moments and product of area for the cross-section if; • D = 67 mm • B = 41 mm • t = 2.41 mm. From these, calculate the position and orientation of neutral axis for pure bending in the vertical plane (i.e. bending about a horizontal axis). Also calculate the directions of the principal second moments of area. Next, graph as scale diagram of the cross-section and plot the neutral axis on that diagram in the correct location and indicate the direction of deflection for the same conditions
A steel strut S serving as a brace for a boat hoist transmits a compressive force P = 57 kN to the deck of a pier as shown in the figure. The strut has a hollow square cross section with wall thickness t = 9 mm and the angle θ between the strut and the horizontal is 51°. A pin through the strut transmits the compressive force from the strut to two gussets G that are welded to the base plate B. Four anchor bolts fasten the base plate to the deck. The diameter of the pin is dpin = 15 mm, the thickness of the gussets is tG = 12 mm, the thickness of the base plate is tB = 10 mm, and the diameter of the anchor bolts is dbolt = 12 mm. Determine the bearing stress between the anchor bolts and the base plate in MPa.
Learning Goal: To solve for forces in statically indeteminate bars with axial loads The square bar shown (Figure 1) is 70 mm thick and 4.8 m long and is fixed supported at both ends. Aload directed leftward s appled at point C, as shown, La =3.02 m from the left end. The modulus of elasticity is E = 100 GPa if point C maves 8 = 0 175 mm to the left what is the applied force? When the number of reaction forces is greater than the number of equilitrium equations, the system is Express your answer with appropriate units to three significant figures. statically indeteminste Solving for the reactions requires some additional equations. These additional View Avallable Hint(s) equations come from considering compatibility relationships (1e, continuity of displacements and relationships berween displacements ana ioads). For an axially loaded member, the compatibility relationship for the deflections can be written by setting the total relative axial displacement between the ends of the member…
Truss members supporting a roof are connected to a 26-mm-thick gusset plate by an 18-mm diameter pin, as shown in the figure and photo. The two end plates on the truss members are each 14 mm thick. Disregard friction between the plates. Roof structure Truss member. P End plates Pin t = 14 mm Gusset plate 26 mm Truss members supporting a roof (a) If the load P = 60 kN, what is the largest bearing stress acting on the pin? (Enter the magnitude in MPa.) MPa (b) If the ultimate shear stress for the pin is 190 MPa, what force Pult is required to cause the pin to fail in shear? (Enter the magnitude in kN.) KN