i need the answer quickly IZV1 Oue 11:09 e* * SIM GUbDec 25, 2021 at 11:58 AM.pngA frictionless piston-cy linder devicecontains 5 kg d R-22 at 10°c. Heat istransferred to the ylindor, calulsing the Prston frition lessto raise untrl it raches a set of stopsat which polut the volume has doubled.Additienal heat is transferred until the temp V2 = 2 Viin side veaches 50°c, at which Point the T3 = 50Pressure inside Hhe cy linder is 1.3 M Pa-Plet the P-v ding, and And:D initial aud final Volume (Vial v)O initial Pressue. (Pi)O initial and fined quality CAand X)@ the work done (Wi3)-StopsR-22Ti 10°CP3 =13 MPa

Given: m= 5 kg T1=10oC T3=50oC P3=1.3 MPa To determine: Initial and final volume Initial pressure…

Answered: D initial gul final Volume (Vi al v) O…

D initial gul final Volume (Vi al v) O initial Pressure.(Pi) ® initial and fined quality Ca,and Xg) @ the work dove (Wi3)-

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Discuss the rock cycle
can you solve part B without just using those tables to find the answer?
Show your complete solution.
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
Simple Machines-Levers, Inclined Planes, and Pulleys Directions: Use the appropriate equation to answer the following questions. All answers should be recorded below or in your Engineering Design journal. Remember to show all work. A lever has an effort arm that is 5 meters long and a resistance (load) arm that is 3.5 meters long. How much effort is needed to lift a 100 Newton weight? 5K i). Draw the figure representing the problem ii). How much effort is needed to lift a 100 Newton weight? iii). What is the Actual Mechanical Advantage 1. 5m i) AOON 5-5m
I need the answer as soon as possible
hints: The ﬂask will be filled with water (at a constant rate of 500 gallons per minute). It will take me exactly 10 minutes to escape from the chains. The diameter of the tank at 1 foot intervals. I am 5 feet 9 inches tall, and I'm pretty skinny so that you can ignore both my volume and the volume of the stool in your analysis. A gallon is equal to 0.13368 cubic feet. You can think of the volume and the height of the water as functions of time. You can easily find an expression for V (t), and then use your expression for volume in terms of height to solve for h(t). after 10 minutes amount of water in the tank=66.84 ft3 t=69.3 minutes h(t)=e66.84t/100? -1 h(10)=e66.84(10)/100? -1=7.39 ft Height of stool=1.64 ft Height of water in the tank=7.39 ft Questions: show work How fast is the water rising? I would like to know how long I will have to hold my breath during the last part of the stunt.
P-4 Please I need help with this question needed very clearly and step by step explanation and needed with clear handwriting please, will be really appreciated for your help
Don't submit the wrong solution.
1. “The grain size of metal sheet influences its formability in two opposing ways. The yield strength of a metal increases as the grain size decreases. So, the formability of a component may decrease if the grain size gets too small. Larger grained metals have better formability, but the roughened surface that results from stretching metal with grain sizes that are too large is unacceptable for many applications. During a recrystallization anneal new grains form in the metal. The final grain size depends on the annealing temperature and annealing time.” As shown in the figure below (1"x1" area under a 50Xmagnification microscope), a cold-rolled metal has been annealed at 550 degrees C for one hour. Calculate the ASTM Grain Size Number for the following condition: image attached