Current Attempt in ProgressA cantilever timber beam with a span of L = 3.9 m supports a uniformly distributed load w. The beam width is b = 270 mm and the beamheight is h=140 mm. The allowable bending stress of the wood is 5.8 MPa. Determine the magnitude of the maximum load w that maybe carried by the beam.Answer: w=LIBbkN/m.

Answered: Image /qna-images/answer/02491181-cc87-4a69-a289-9262e9dea9aa.jpg

Current Attempt in Progress A cantilever timber beam with a span of L = 3.9 m supports a uniformly distributed load w. The beam width is b = 270 mm and the bear height is h=140 mm. The allowable bending stress of the wood is 5.8 MPa. Determine the magnitude of the maximum load w that may be carried by the beam. Answer: w= IB b kN/m.

Current Attempt in Progress A cantilever timber beam with a span of L = 3.9 m supports a uniformly distributed load w. The beam width is b = 270 mm and the bear height is h=140 mm. The allowable bending stress of the wood is 5.8 MPa. Determine the magnitude of the maximum load w that may be carried by the beam. Answer: w= IB b kN/m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cantilever timber beam with a span of L = 2.8 m supports a uniformly distributed load w. The beam width is b = 260 mm and the beam height is h = 210 mm. The allowable bending stress of the wood is 5.2 MPa. Determine the magnitude of the maximum load w that may be carried by the beam. Answer: w = i kN/m.
A cantilever timber beam with a span of L = 2.6 m supports a uniformly distributed load w. The beam width is b = 250 mm and the beam height is h= 140 mm. The allowable bending stress of the wood is 5.9 MPa. Determine the magnitude of the maximum load w that may be carried by the beam. Answer: w= i eTextbook and Media Save for Later kN/m. Attempts: 0 of 3 used Submit Answer
solve for the wind load on the right side
solve the wind load on the left side
Question 5 A rectangular presressed concrete beam of span 15 m and width 500 mm is loaded with a live load of 30 kN/m. The prestressing force is KN. [Take permissible stresses in concrete and steel as 15 MPa and 1200 MPa respectively]
Answer problem1
A TIMBER BLOCK “B x B” mm SQUARE IS REINFORCED ON OPPOSITE SIDES BY A “B” mm AND ‘t’ mm THICK STEEL PLATES. DETERMINE THE THICKNESS ‘t’ SO THAT THE ASSEMBLY WILL SUPPORT AN AXIAL LOAD OF 1000 KN WITHOUT EXCEEDING A MAXIMUM TIMBER STRESS OF 12 MPa OR A MAXIMUM STRESS IN STEEL OF 350 MPa. MODULUS OF ELASTICITY OF STEEL AND TIMBER ARE 210 GPa & 7 GPa RESPECTIVELY.
The steel framework shown below is used to support the reinforced concrete slab (unit weight of concrete =23.6KN/m3) that is used for an office use (minimum live load = 2.4KPa). The slab is 150 mm thick. Use a=3m, b=5m. Neglect the self-weight of the beam and girder. Assume all beams and girders have simple supports. NSCP 2015 Load factors: 1.2DL & 1.6LL. Calculate the total ultimate/factored liveload in Kilo Pascals? Express your answer in 2 decimal places
A rectangular reinforced concrete beam has a cross-section dimensions b=400mm andoverall depth h= 800mm. The beam as shown in the image below carries asuperimposed dead load of 12 kN/m (excluding the self-Weight of the beam) andspecified live load of 20 kN/m. The beam has a compressive strength of 30Mpa andreinforcement yield strength of 400 Mpa a) What is the self weight of the beam? b) What is the modulus of elasticy and yeild strain of reinforcement
A simply supported wood beam of length L = 8 ft carries a concentrated load P at midspan, as shown. The cross- sectional dimensions of the beam are b = 7 in. and h = 13 in. If the allowable shear strength of the wood is 130 psi, determine the maximum load P that may be applied at midspan. Neglect the effects of the beam's self-weight. 12 Answer: P = IM P B 7/2 C X lb N b h
4
A simply supported timber beam 20 cm wide and 40 cm deep carries a point load W at the middle point. The permissible stresses in flexure (bending) and shear is 100 N/cm2 and 150 N/cm2 respectively. Calculate the span length below which the shear stress will govern the safe load and above which the bending stress will govern the safe load.