Critically analyze the two modes of asynchronous data transfer techniques accompanied by suitable diagrams when the speed of I/O devices do not match with microprocessor and the timing characteristics of the I/O device is not predictable. In addition, discuss the limitation of each data transfer approach.

Critically analyze the two modes of asynchronous data transfer techniques accompanied by suitable diagrams when the speed of I/O devices do not match with microprocessor and the timing characteristics of the I/O device is not predictable. In addition, discuss the limitation of each data transfer approach.

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter4: Processor Technology And Architecture

Section: Chapter Questions

Problem 2PE: If a microprocessor has a cycle time of 0.5 nanoseconds, what’s the processor clock rate? If the...

See similar textbooks

Similar questions

If a microprocessor has a cycle time of 0.5 nanoseconds, what’s the processor clock rate? If the fetch cycle is 40% of the processor cycle time, what memory access speed is required to implement load operations with zero wait states and load operations with two wait states?
The subject of how the size or breadth of a bus impacts or has an effect on the architecture of a computer system in relation to the transmission of data is an important one. Provide evidence for your thesis by citing specific instances.
Let us suppose, for the sake of simplicity, that each instruction on a RISC processor is processed in 2 microseconds and that an I/O device can only wait for an interrupt to be handled for a maximum of 1 millisecond before it is serviced. When interruptions are turned off, the number of instructions that may be performed is limited.
(a) Draw a block diagram of a typical Data Acquisition System (DAQ) from transducer to computer. Briefly explain each element. (b) What is the General Purpose Interface Bus (GPIB) and what are the three general classes of devices that can be connected to a GPIB bus? In what standard configurations can devices be connected to the bus? - How many devices can be interconnected to one bus and what address settings can they have?
The subject of how the size or width of a bus affects or influences the architecture of a computer system is a crucial one to consider in relation to the transmission of data. Provide evidence in the form of concrete examples to back up your claim.
Consider a simple read-only memory (ROM) unit with 2-bit addressand 2-bit data buses.Draw the internal architecture of such a ROM unit includingtransistors, address and data signals, and the row decoder.? I have attached the answer to the question, but I am confused by it, if you could explain every step including how many transistors to use, where to place them and the basic procedure which could be used with other similar questions that would be helpful
Consider a simple read-only memory (ROM) unit with 2-bit addressand 2-bit data buses.Draw the internal architecture of such a ROM unit includingtransistors, address and data signals, and the row decoder.? I have attached the answer to the question, but I am confused by it, if you could explain every step including how many transistors to use, where to place them and the basic procedure which could be used with other similar questions that would be helpful, do not copy and paste off chatgpt
Question 4 Why must the single-cycle datapath have separate instruction and data memories? The formats of data and instructions are different in RISC-V, and hence different memories are needed. It is less expensive to have separate memories. The processor operates in one cycle and cannot use a (single-ported) memory for two different accesses within that cycle. All of the above.
There are several approaches to hardware multithreading, fine-grained, coarse-grained and simultaneous (SMT). What are benefits and disadvantages of each one of them and if and where are they used.
Discuss with suitable diagram and how data transfer can be done between CPU and considered I/O device using Strobe control method of data transfer. Give your reflection on disadvantage in this method of data transfer.
Explain the difference between Harvard and von Neumann architectures in the context of microcontrollers.
“There is a mechanism in which CPU relinquishes the control over the buses for carrying out various operations between memory unit and I/O unit.”Justify your answer and explain such process in detail with the help of suitable diagram.