Course: Electrical Engineering Subject: Electrical Apparatus Instructions: Write the GIVEN with their respective symbols and units. • Do not skip the SOLUTIONS, do it step-by-step with their respective symbols and units • Round up to 3 three decimal places the FINAL ANSWERS and BOX it. Problem: An abc-phase sequence three-phase balanced wye-connected source supplies power to a balanced delta-connected load. The impedance per phase in the load is 14 + j12 Q. If the source voltage for a phase is Van=120280° Vrms, and the line impedance is zero, find the phase currents in the wye-connected source.

Course: Electrical Engineering Subject: Electrical Apparatus Instructions: Write the GIVEN with their respective symbols and units. • Do not skip the SOLUTIONS, do it step-by-step with their respective symbols and units • Round up to 3 three decimal places the FINAL ANSWERS and BOX it. Problem: An abc-phase sequence three-phase balanced wye-connected source supplies power to a balanced delta-connected load. The impedance per phase in the load is 14 + j12 Q. If the source voltage for a phase is Van=120280° Vrms, and the line impedance is zero, find the phase currents in the wye-connected source.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.43P: Three single-phase transformers, each rated 10MVA,66.4/12.5kV,60Hz, with an equivalent series...

See similar textbooks

Similar questions

The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three-phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three- phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT RO- SO- To- : IR Is IT UL-380 V CARGA 1 P₁ = 950 W cos p1=0,5 ind. CARGA 2 P₂=1.140 W cos p₂=1 CARGA 3 P3=760 W cos p3=0,5 cap.
X₂=0.1 1 XL +03 Soto X₁ = 0.2 X = 0.1 X = 0.1 Above is the one-line diagram of a simple power system. Each generator is represented by an emf behind the subtransient reactance. All impedances are expressed in per unit on a common base. All resistances and shunt capacitance are neglected. The generators are operating on no load at their rated voltage with their emfs in phase. A symmetrical fault occurs at bus 1 through a fault impedance Z, =j0.08 per unit. a) Using Thevenin's Theorem, determine the impedance to the point of fault and the fault current in per unit. b) Find the bus voltages and line currents during the fault. 2 O oto
Need asap pls help. Solve for the voltages across and currents through each component. Show the complete solution and explain. The total power should be zero..
2. Two transformes A and B of ratings 5uokVA and 25okVA. Supplying a load kVA of 750 ato.8Pf lagging. open circunt valtajes are 400V and 410v respectively. Trusfarmn A has 1/ nsistance and 5/ ractance and traugformer B hay 1.$, mesistona and 41 reactance. Find (^) Crossacarent in the seandaries on no.load.ib) the load shared by euch transfarmer Their are
A three-phase circuit is balanced. The source voltage for the a-phase has a magnitude of 100 volts, and you can assume the phase angle is a reference of 0 degrees. Write the phasor expressions with proper subscript notation for the source voltage for each leg of the three-phase source if it is in a positive phase sequence.
How can I compute and get the values of branch currents (Iab, Iac, Ibc, Ibd, Icd and Ica) and the algebraic sum of the potential difference for electrical loops (abca, abdca, acda, abcda and acbda) by using Kirchhoff's voltage and current law (KVL and KCL) equations?
1) Referring to the circuit as in Figure 1, transform the circuit in phasor domain representation.2) Determine the value of total impedance, ZT3) Determine the value of total current, IT4) Determine the value of branch current, I1 and I25) Determine the value of voltage across resistor, R1, R2 and R36) Determine the value of voltage across capacitor, C1 and C27) Determine the value of voltage across inductor, L.
Draw Wye- Delta three phase transformers connection ( no-load and full-load) in Lt-spice
Discuss how delta connection is achieved in three-phase systems?
A workshop from a 231/400 V transformer center with a 3-phase and four-conductor underground cablefed. The resistance of the phase conductors is 0.035 ohms and the resistance of the neutral conductors is 0.05 ohms.25 kVA at 0.8 reverse power factor from R phase of the supply line, 0.8 forward power factor from S phase 15Fully ohmic loads of 10 kVA are drawn from kVA and T phases.(a) Find the currents flowing through the phase conductors and neutral conductors.(b) Voltage drops between the transformer substation and the workshop and at the load terminals.calculate the voltages(c) Plot the supply line currents and phase voltages phasorally.