Could you find the HI, ELEVATIONS, CORRECTIONS and Adjustments of Elevation values according to the informations were given in the table below? Please write your answers on an A4 paper with your name, school number and signature to show the phases of solving. Afterwards, you can upload it on LMS system as pdf, jpeg, etc Adj. Setup Station BS HI FS ELEV. CORR. Elev. BM Mil 1,12 2035,23 1 TP1 0,3 8,55 2 TP2 0,76 7,05 3 ТРЗ 0,45 9,82 4 ВМ Oak 11,6 9,51 5 ТР4 12,35 1,71 6 ТР5 11,37 0,63 7 BM Mil 0,19

Could you find the HI, ELEVATIONS, CORRECTIONS and Adjustments of Elevation values according to the informations were given in the table below? Please write your answers on an A4 paper with your name, school number and signature to show the phases of solving. Afterwards, you can upload it on LMS system as pdf, jpeg, etc Adj. Setup Station BS HI FS ELEV. CORR. Elev. BM Mil 1,12 2035,23 1 TP1 0,3 8,55 2 TP2 0,76 7,05 3 ТРЗ 0,45 9,82 4 ВМ Oak 11,6 9,51 5 ТР4 12,35 1,71 6 ТР5 11,37 0,63 7 BM Mil 0,19

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Show calculations and fill in the blanks
Please *recheck and provide *clear and complete *step-by-step solutions in scanned handwriting or computerized output. Thank you.
When conducting traverse surveys, what are the two laws that are often used to correct the misclosure of the vertical and horizontal distances? (Check) 2 (multiple choice questions) □ A. Theodolite law, suitable for distance and angle accuracy B. Compass rule, suitable for distance measurement accuracy far worse than angle measurement accuracy C. Compass law, suitable for distance and angle accuracy □ D. Theodolite law, suitable for distance measurement accuracy far worse than angle measurement accuracy
Item 6 The angles of a five-sided traverse are turned so that the 95% error of any angle is +3.4". Part A What is the 95% error in the traverse? Express your answer in seconds to three significant figures. E95 = Submit Provide Feedback Avec Request Answer ?
Below is a profile level notes, indicate the missing data, show arithmetic check, and draw the profile leveling. What is the difference in elevation from station 0+060 to 1+260? Also, the difference in elevation from BM1 to BM2?
answer ASAP! UPVOTE WILL BE GIVEN! PLEASE WRITE THE COMPLEETE SOLUTIONS AND LEGIBLY! FUNDAMENTAL OF SURVEYING The left and right water edges of a river are 3.75m and 65.25m, respectively, from an initial reference point. Verticals are located at distances of 11.25, 19.25, 27.25, 35.25, 43.25, 51.25, and 59.25m, respectively, from the reference point. The corresponding depths of verticals are 5.2, 9.7, 9.6, 10.0, 10.4, 10.0 and 4.2 meters. Mean velocities in the verticals are 0.16, 0.60, 0.75, 0.92, 0.97, Activ 0.98, and 0.65 m/sec, respectively. Disregarding the end to sections, determine the following: Discharge & Mean velocity of the river.
2. Find the force in members BC, BE, EF using the method of section. Show the free body diagram with required dimension's and inclinations: Olncluded in manual solution ONot made The force in member EF: N [Tension:+, Compression: -1 The force in member BC: N [Tension:+, Compression: -] The force in member BE: N [Tension:+, Compression: -] (Answer upto 1 decimal place for all values) 2 Without any calculation identifu the zore forco mamberc in the tacs nere to search
Show complete solution and diagram
Topic: Surveying Please compute the Average of point 1,2 , and 3 in the table. Thanks!
3. Complete the accompanying set of differential leveling notes and perform the arithmetic check.
Traverse adjustment and area computation
Item 2 Part A What error results on a 20-m sight with a level if the rod reading is 1.7060 m but the top of the 4-m rod is 0.3 m out of plumb? Express your answer to two significant figures and include appropriate units. error = Submit Provide Feedback Value Request Answer Units ?