coordir (y-coordinate; the y-axis section.) and horizontal coordinate (z-coordinate) of the location where the maximum shear stress occurs in the section are y= Z= mm; mm; The vertical distance from the location where the maximum shear stress occurs in the section to the bottom side (AB) of the cross section can be calculated as Distance = mm

coordir (y-coordinate; the y-axis section.) and horizontal coordinate (z-coordinate) of the location where the maximum shear stress occurs in the section are y= Z= mm; mm; The vertical distance from the location where the maximum shear stress occurs in the section to the bottom side (AB) of the cross section can be calculated as Distance = mm

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.16P: Figure (a) shows the cross-sectional dimensions for the structural steel section known as C1020...

See similar textbooks

Similar questions

A cross-section of a beam is shown in Figure Q2. If the shear force in this section is V = 281 KN, determine the value and the location of the maximum shear stress in the section. In Figure Q2, a = 72 mm and the origin of the coordinate system is at centroid of the cross section. Z A a AY 2a O 4a Figure Q2 J.L B 3a a
A cross-section of a beam is shown in Figure Q2. If the shear force in this section is V = 125 KN, determine the value and the location of the maximum shear stress in the section. In Figure Q2, a = 58 mm and the origin of the coordinate system is at centroid of the cross section. A a 2a 0 4a a 3a a
The cantilever beam is supported by a fixed support at A, and subjected to the force F = 550 lb and the couple M = 2870 ft-lb. Draw the shear force and bending moment diagrams (in your homework documentation) and determine the equations for V(x) and M(x). Take x = 0 at point A. c 03O 2013 Michael Swanbom F CC BY NC SA M A • B a Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value 6.2 ft 4.34 ft Support Reactions The force reaction at A is lb (take up as positive). The couple moment reaction at A is lb (take counterclockwise as positive). Shear Force and Bending Moment Equations In section AB: V(x)= lb and 'M(x)= ft-lb. In section BC: V(x)= lb and 'M(x)= ft-lb.
Q2 : Draw the load and the bending moment diagrams that correspond to the given shear force diagrams in the figures below. V (kN) 114 94 14 x(m) 2 1.4 -66
The cantilever beam is supported by a fixed support at A, and subjected to the force F = 600 lb and the couple M = 2810 ft-lb. Draw the shear force and bending moment diagrams (in your homework documentation) and determine the equations for V(x) and M(r). Take a = 0 at point A. a •b C M A- В Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 5.2 ft b 3.9 ft Support Reactions The force reaction at A is Ib (take up as positive). The couple moment reaction at A is ft-lb (take counterclockwise as positive). Shear Force and Bending Moment Equations In section AB: V(x)- In section BC: V(x)- lb and M(x)= ft-lb. lb and 'M(x)= ft-lb.
You are required to calculate the second moment of area about the x-axis for the figure below. a mm b mm a mm a mm One method for calculating the second moment of area is to break up the shape into three parts as shown below. Calculate the second moment of area of segment 2 if: a = 30.67 mm b = 21.14 mm |_x = mm^4 a mm ww e
If F1= 24kN F2=26kN F3=21.5kN Calculate the second area of moment of the beam using the dimensions in the attached image
Determine the value of Q of the Transverse Shear Stress formula [T = (VQ)/(It)] at the point of vertical height 12 mm from x-axis in mm for the cross section shown in Figure 5.2a. Given B = 120 mm, D = 120 mm, tf = 75 mm, tw = 15 mm and location of centroid from x-axis = 74.674 mm. - B Figure 5.2a
MpQupq rx F, where r is a position vector from any point on the line through P and Q to R and upo is the unit vector in the direction of line segment PQ. The unit vector upo is then multiplied by this magnitude to find the vector representation of the moment. As shown in the figure, the member is anchored at A and section AB lies in the x-y plane. The dimensions are x₁ = 1.5 m, y₁ = 1.7 m, and zi = 1.6 m. The force applied at point C is F=[-150 i+ 135j + 190 k] N. (Figure 1) Figure Yı B < 1 of 1 ▼ Submi ✓ Correct Part C Calculating the moment about AB using the position vector BC Previous Answers MAB =[ Using the position vector from B to C, calculate the moment about segment AB due to force F. Express the individual components to three significant figures, if necessary, separated by commas. View Available Hint(s) 17| ΑΣΦ ↓1 vec Submit Provide Feedback Previous Answers Request Answer X Incorrect; Try Again PPearson → O с 4 ? Res i, j, k] N m Next
2) The cantilevered L-bracket has applied loads of P and Q at point A. Find M, V, and N in each section of the structure (from A to B, then B-C). Choose a coordinate system that follows the right hand rule and write equations as a function of x and y for each section. The thickness of the beam is negligible for this problem. 2 Q P
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a= 2.5 m, b= 7.0 m, MB = 85 kN-m and Mc = 130 kN-m. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. y MB Mc В C D Determine the shear force acting at each of the following locations: (a) x = 0+ m (i.e., just to the right of point A) (b) x = 2.5- m (i.e.,. just to the left of B) (c) x = 2.5+ m (i.e., just to the right of B) (d) x = 12.0- m (i.e. just to the left of D) When entering your answers, use the shear force sign convention. Answers: (a) V = i kN. (b) V - i kN. (c) V = i kN. (d) V = i kN.
A moment about the z-axis of 192 N-m is applied to a beam with dimensions b = 85 mm and h = 302 mm. If there are no other loads applied to the beam (My, P, Vy and Vz = 0), what is the normal stress at point F? Give your answer in kPa to two decimal places with negative indicating compression and positive indicating tension. b/4 М, h E Ihis F h/3 В M. D b/4