Convert the following from mg/L as the ion or compound to mg/L as CaCO3: 90 mg/L Ca2+ 00 mg/L HCO3- 0 mg/L MgO 40 mg/L CO

Q: choose

A: Newton's third law of motion states that every action there is an equal and opposite reaction

Q: ecific gravity of 13.6 contained in the tank. Wh rcury surface O 0.29 V O 0.34 V O 0.74 V O 0.47 V

A:

Q: A particle starts from rest at a position x(0) = 0. Find the velocity v(t) and position y(t) of the…

A: To determine the equations for velocity and position of a particle with the given acceleration…

Q: When a body is completely immersed in a liquid, its stability depends on the relative positions of…

A: Buoyancy force acts in vertically upward direction and weight of body acts in vertically downward…

Q: A particle start its motion from rest under the action of constant force. if the distance covered in…

A:

Q: 3.5 6.87X X² +4 =)dx

A:

Q: The value of K, for hypochlorous acid , HCIO , is 3.50x10-8 Write the equation for the reaction that…

A:

Q: Chlorine gas (7 mg/1 as Cl,) was added to water sample. The free residual chlorine and pH are 2 mg/1…

A:

Q: Calculate the atomic densities of the directions [100], [111] and [110] in a face centered cubic…

A: Draw the (100) Face centered cubic plane structure. It is required to determine the number of atoms…

Q: 21. To gain structural strength, the dimensions of aluminum are increased. T or F 22. 35% of…

A: Comment As per our policy, we cannot answer all multiple subparts,  Since your question has multiple…

Q: It is seen that solids and liquids will have different coefficients of volume expansions for…

A: Coefficient of volume expansion:- The unit increase in the unit volume of any substance following…

Q: Question 36 The EMC represents a region where properties of the wood begin to change. Select one: O…

A:

Q: Which statement below is true about the reaction, Hg2Cl2→HgCl2+Hg?   It can't be a redox reaction.…

A: The given chemical reaction is: Hg2Cl2→HgCl2+Hg In this chemical reaction oxidation and reduction of…

Q: Hot working is a process commonly seen in the production floor that usually involved heating…

A: Hot-working is the metalworking process that is carried out at a temperature greater than the…

Q: Why there is no 9.81 in P2 when its formula is p2= p1 + specific weight(9.81) (h)

A: P1=1030g/cm3

Q: RTC means? * Your answer For the particles of an atom, which two particles have the same mass? *…

A: RTC - Regensburg Theoretical Chemistry   Protons and Neutrons have same mass - 1.67*10-24grams

Q: (Lola) A Glycerin has a Mass(M)= 945 Kg. And a Volume (V)= 0.750 M3.---The Specific Weight .8 岛 :is…

A: Specific Weight is defined as weight per unit volume. Weight is a force. The unit for specific…

Q: Which of the following statement is correct? The viscosity of liquid decreases with increase in…

A:

Q: You have two amino acids, i,e. glycine and alanine. What are the structuresof two possible…

A: The process of formation of organic compound from the combination of amino acids is known as…

Q: 9. Which of the systems are equivalent to the couple in ta) (b) 73 Ib 100 h 75 h d) 75 45 Ib 45 b 45…

A: B an D is right. Calculated couple moment of A A= 60×5 =300 lb-ftCalculated couple moment of B B=…

Q: Radium decomposes at a rate proportional to the quantity of radium present. Suppose that it is found…

A:

Q: Endothermic reaction is a chemical reaction which produces heat. Select one: True False

A: Finding out Endothermic reaction is a chemical reaction which produces heat is true or false.

Q: gel pores and capillaries decrease with the progress of 5 points cement hydration * True False…

A: Finding out given statement are true or false.

Q: Period 6 is unusual in several ways.(a) It is the longest period in the table. How many elements…

A: Period 6 accommodates a total of 32 elements from Cesium (At. No. 55) to radon (At. No. 86). Out of…

Q: When chlorine (Cl2) gas is added to water during the disinfection of drinking water, it hydrolyzes…

A:

Q: reaction equation is A+B=C and the reaction rate can be writtten as dCA/dt=r=-kCACB2. a) What is…

A: The order of a reaction is  the sum of the power on the concentration terms for a rate law, Hence…

Q: C A D B E 10 cm 40 cm 40 cm 10 cm vo uniform rods AB and CE, each of weight 20 N and length 1 m, e…

A: W=20N L=1m

Q: Steam in a piston-cylinder assembly undergoes a polytropic process, with n = 2, from an initial…

A: Given data:Initial specific volume, V1​=1.75440ft3Initial pressure,  p1​=450lbf/in2Initial specific…

Q: A fluid in motion suffers a frictional loss, which is an expenditure of energy required to overcome…

A:

Q: In an ion exchange process, which ion has a higher affinity for exchange: Potassium ions (K+) or…

A: Calcium ions has a very high affinity. According to the  general principles  The higher the charge,…

Q: : What mass of AgNO3 is needed to convert 3.46g of Na2CO3 to A92CO3, and calculate the mass of…

A:

Q: Assume an ideal-gas equilibrium holds for the following reaction: SO2 + 02 + SO3 Draw a qualitative…

A:

Q: us PO4 us F, Cl, Br, or I ent only g minerals: Formula CaSO4

A: mineral groups are given as  silicates carbonates  sulfates sulfides oxides hydroxide phosphates…

Q: An airplane has a half-wingspan of 32 m. Determine the change in length of the aluminum alloy [α =…

A:

Q: For gases under certain conditions, there is a relationship between the pressure of the gas, its…

A: As , PV=mRTP=Pa=Nm2 =kgm-s2V=m3 , m=kgT=k

Fluid Materials

In general terms, anything that flows can be termed as a fluid. In other words, a fluid is any substance that cannot resist shear forces and deforms continuously under the application of external shear forces. Fluid materials differ completely from solid materials such as metals and alloys. For instance, if we consider two infinitesimally small cross-sectional areas of fluid materials and solid materials, and apply shear forces to these elements, both the elements will undergo deformation. Upon releasing the shear force, the element of the solid materials will regain its original orientation, but the element of the fluid materials will keep on deforming continuously under the action of the shear force.