convert 259 lb/ft2 to kg/in2

Q: Example: 600 Compute the positive design moment capacity of the T-section beam. fe = 20 MPa, fy =…

A:

Q: 1. Find the height of the water in the figure shown neglect effect of air. PB = 0.2 ke/cm² PA =…

A: Given data in question  Pressure at point A and B Depths Specific gravity To find out  Value of H…

Q: Determine the moment ereated by the weight of the traffic light about point O The dimensions of the…

A:

Q: Block A has a mass of 100 kg and the coefficient of friction is 0.20. Determine the friction force…

A:

Q: determine the moment of inertia along x and y axis with respect to the given axis and with respect…

A:

Q: The blocks shown are separated by a solid strut which is attached to the blocks with frictionless…

A:

Q: Show free body diagram and complete solution. Thank you

A:

Q: solve for member BD and CE

A:

Q: rmine R in N at point C.

A: 200kg=2009.81=1962N20lbf=204.448=88.964N

Q: Situation: A bicycle tire is inflated with air. The density of the air in the inflated tire is 0.4…

A:

Q: Determine the tension T in the belt needed to overcome the tension of 200 lb created on the other…

A: Given :

Q: fluıd mechanıcs If an oil tank is pulled uphill on a surface that makes an angle of 162 with the…

A: Given  Angle made by hill with the ground = 162 °  Angle made by oil = 160   Applied pulling force =…

Q: Calculate the allowable axial capacity in kN if Fy = 345 MPa. Write your answer rounded to the…

A: Given, W14 x 53 L = 8.2 m or 8200 mm Fy = 345 MPa

Q: In the given figure, the 280 lb-bar AB is 10 ft long and hinged at B. It rests upon a 400N- block at…

A:

Q: A plate 0.025 mm distant from a fixed plate, moves at 60 cm/s and requires a force of 2 N per unit…

A:

Q: Determine the magnitude of the resultant of the three forces shown F₁ = 70 N 3 5 4 F₂ = 80 N O 33.8…

A:

Q: A block of mass 70.03 kg sits on top of a table and a horizontal force of 240 N is applied on the…

A:

Q: 1-77 For the beam shown in Fig. P1-77, determine a. The reactions at supports A and B. b. The…

A:

Q: When the 64-in cube is immersed in ethanol (SG = 0.747), it is balanced on the beam scale by a…

A:

Q: A RA 4 ft 900 lb B 60 lb/ft 8ft. C Rc 6 ft 400 lb D

A:

Q: Q2. Analyze the following frame as shown in the figure. AB has 21, BC has 1.51, and BD has I. 120 kN…

A: carry over moment -  its the moment developed at one end due to applied moment at other end .  when…

Q: A piece of material experiences a unknown distributed load of snow along its entire surface area of…

A: Given snow behaves as water so unit weight of snow = ρ = 62.4 lbft3 As snow is varying in height…

Q: A simply supported 5-meter beam is an S-Beam, S610 x 119. If the beam has no external load, what is…

A:

Q: 26 Compute the resultant of the forces shown in the figure. F1 F21 m 1 m F4 F3 A F1 = 15 KN F2 = 25…

A:

Q: A plate at 0.010 mm distant from a fixed plate, moves at 10 cm/s and requires a force of 1 N per…

A: given- speed du=10 cm/s=10×10-2 m/sdistance dy=0.010 mm=0.010×10-3 mshear stress τ=1 N/mm2=106 N/m2

Q: am wondering how I would go about solving this problem. I do not understand how to use the parabola.

A: In order to solve this question. We need to calculate the centroid and the resultant positive and…

Q: Dimensional Analysis 138.57 kg/m3 = lb/ft3

A:

Q: Situation 3: A W10x100 has a length of 9.10 m. Fy = 248 MPa. The properties are given below.…

A:

Q: Given the beam loaded below, compute the following: a. Reaction @ support A b. Reaction @ support B…

A: Given:- To find:- Reaction at support A Reaction at support B

Q: Draw completey the shear and moment diagrams.

A: Solution: Analyze the continuous beam using the moment distribution method: Free body diagram:

Q: A flat plate of area 2x10 cm is pulled with a speed of 0.5 m/s relative to another plate located at…

A: We will balance the force.

Q: P 150⁰ B O 1m A 2m O

A: Now we have to find the ratio of extension of rod A to that of rod B

Q: ( 2/3) W 2W W L/2L. - L· - L/2 – L -

A:

Q: 3. The tow truck’s front wheel will be lifted off the ground if the moment of the load W about the…

A: The largest weight carried by the tow truck is 6020lbExplanation:Step 1:Weight of the truck is…

Q: The 162-oz golf ball is struck by the five-iron and acquires the velocity shown in a time period of…

A: The average force R can be determined as, R(∆t)=mv-muR(∆t)=mv-m(0)R(0.0019 s)=1.62 oz32.2…

Q: An aluminum bar having a cross-section area of 0.5 m2 carries the axial loads applied as shown in…

A:

Q: of mass is at Determine which Free Body Diagram can be used to find the least coefficient of static…

A:

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.