Consider there is a recording session to capture animal sounds in a particular region using a 3-bit ADC. i. Determine the value of maximum voltage zone number the ADC can have. ii. If the signal amplitude range is 0 V to 4 V, determine the resolution of the ADC. iii. If the measured voltage is 3.5 V find the voltage zone which belongs this voltage and determine its binary code word.

Consider there is a recording session to capture animal sounds in a particular region using a 3-bit ADC. i. Determine the value of maximum voltage zone number the ADC can have. ii. If the signal amplitude range is 0 V to 4 V, determine the resolution of the ADC. iii. If the measured voltage is 3.5 V find the voltage zone which belongs this voltage and determine its binary code word.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

ChapterS: Safety, Basic Electricity And Ohm's Law

Section: Chapter Questions

Problem 8RQ: What is an MSDS?

See similar textbooks

Similar questions

[0 5] the signal in the volt range will be quantified. since n=4; a)Calculate what is the number of Qunta levels? b) Calculate what is the quantization interval? c)V=3.2 volts rounded to what quantization level? Let's draw with Quantalama level chart
b. Explain how to decide the sampling rate for a multi-frequency input signal. c. An ADC with word length of 24 bits. If the input analogue signal range is 3.7 V, what is the resolution of this ADC? d. Consider a thermocouple giving an output of 0.5 mVrc. What will be the word length required when its output passes through an ADC if temperatures from 0°C to 120°C are to be measured with resolution of 1.5°C?. Assume 12V as system voltage.
19) Consider a 6-bit ADC and full scale voltage measurement range of (0-59).The Resolution will be _________. 0.30 0.06 0.92 1.00
2a. Assume a digital to analog conversion system uses a 10-bit integerto represent an analog temperature over a range of -25oF to 125oIf the actual temperature being read was 65.325oF, what would bethe closest possible value that the system could represent? 2b. What is the minimum sampling rate needed in order to successfullycapture frequencies up to 155 KHz in an analog signal?
The task of the modulator is: O a. Amplification of the analogue signal before transmission. O b. Converting digital symbols into analogue waveforms. O c. Decompresses the encoded digital signal. O d. Detects and possibly corrects error in the received digital data. O e. Detection of received digital symbols. O f. Introduces redundancy in the digital data to protect against error. g. Compresses the digital signal. O h. Amplification of the received signal with minimal noise.
(b) Consider a voice signal from a analog telephone which needs to be digitized. Explain the steps involved in the conversion of analog to digital signal. If suppose the sampled analog values are 1V, 2V, 3.5V and 4.5V, use a 2 bit quantizer to digitize these values. Assume the range of sampled analog values from 0V to 5V. Provide the digitized values of this signal and draw the digital signal.
Choose the correct answer low HDOP (Horizontal Dilution of Precision) number such as2 indicates a ........................... a.poor fix b.good fix c.poor signal quality d. good signal quality
The information in an analog signal voltage waveform is to be transmitted over a PCM system with an accuracy of : 0.1 % of the peak-to-peak analog signal. The analog voltage waveform has a bandwidth of 43 Hz and an amplitude range of - 10 to 10 Vots. Determine the minimum bit rate fin bps) required in the PCM system? O a 688 O 774 O c 387 O d 86 Oe 258
Which statement is not true for a source encoder? a.reduces the size of the data b.Converts analog information to discrete signal c.Removes redundancy d.Converts digital input to pulsating signal
Q 4. a) Determine control words when the ports of Intel 8255 are defined as follows: Port A as an input port. Mode of the Port A is Mode 0. Port B as an input port. Mode of the Port B is Mode 0. Port C upper and C lower are input ports.
Q2/ The information in an analog signal voltage waveform is to be transmitted over a PCM system with an accuracy of ±0.1% (full scale). The analog voltage waveform has a bandwidth of 100 Hz and an amplitude range of -10 to +10 volts. Find the minimum sampling rate required. i) ii) Find minimum bit rate required in the PCM signal. Find the number of bits in each PCM word. iii) iv) Find the minimum absolute channel bandwidth required for the transmission of the PCM signal.
Qَ\ discuss a conversion of an analogue signal to digital bits Please I need to resolve the question quickly