Consider the truss shown in (Figure 1). Assume the members are pin connected at their end points. Take A = 200 mm² and E= 200 GPa for each member. Suppose that F= 14 kN. Figure 4m E 4 m 24 kN B 4 m. F 1 of 1 > ▶ Part A Part B A₁ = 47.6 Determine the vertical displacement of joint C' measured downward. Use the method of virtual work. Express your answer to three significant figures and include the appropriate units. Enter positive value if the displacement is downward and negative value if the displacement is upward. HÅ X Incorrect; Try Again Provide Feedback mm Submit Previous Answers Request Answer [www] Review ? ✓ Next >

Consider the truss shown in (Figure 1). Assume the members are pin connected at their end points. Take A = 200 mm² and E= 200 GPa for each member. Suppose that F= 14 kN. Figure 4m E 4 m 24 kN B 4 m. F 1 of 1 > ▶ Part A Part B A₁ = 47.6 Determine the vertical displacement of joint C' measured downward. Use the method of virtual work. Express your answer to three significant figures and include the appropriate units. Enter positive value if the displacement is downward and negative value if the displacement is upward. HÅ X Incorrect; Try Again Provide Feedback mm Submit Previous Answers Request Answer [www] Review ? ✓ Next >

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider the truss shown in (Figure 1). Assume the members are pin connected at their end points. Take A = 2.1 in? and E = 29(10³) ksi for each member. Use the method of virtual work to solve this problem. Part A Determine the vertical displacement of joint A measured downward. Express your answer using three significant figures. Enter positive value if the displacement is downward and negative value if the displacement is upward. vec Figure 1 of 1 DA. in. %3D Submit Request Answer 8 ft Provide Feedback Next > A 8 ft 8 ft 1000 lb 500 lb
For the plane truss shown, determine the nodal displacements and member force of the diagonal members. E169 GPa. Cross-sectional areas are 300 mm? for diagonal members and 400 mm? for the rests. Diagonal member is subjected to a temperature increase of 40°C while diagonal D is in fabrication error of 6 mm too short. B=14.6x10*PC. You can use EXCEL or your matrix calculator in determining the nodal displacements. 60 KN KN +75 KN 4 m Ad 3m
Three steel rods, each having a cross-sectional area of 500 mm2, are assembled in a symmetrical manner, ass shown in the igure. Assume that steek behaves as a linear elastic material with E= 200 GPa. Determine the deflection of joint A due to a downward force of P= 2MN
Q1 Using the Stiffness Method procedure identify nodes, elements and degrees of freedom (neglect axial displacement, i.e. EA>>) for the beam shown below. Form member and structure stiffness matrices and compute displacements, reactions and internal forces in the beam under the applied load. Draw the SFD and BMD. Note that there is a hinge at B. Take E = 200 GPa, IAB = 2000 cm4, IBC = ICD= 1000 cm4. A 20 kN OB |1m|1m 6 kN/m 6 m 2 m 10 kN.m
of A square plate (a x a) is a fixed supported on all four edges and carries a uniform load a (per nit area). The equation for deflection is: V"w=q/D where D is flexural rigidity. Take a h=Ax = Ay =-. Find the deflection at internal nodes. %3D 4
Consider the truss shown in (Figure 1). AE is constant. Assume that AE is in kN. Use the principle of virtual work to solve this problem. Show Transcribed Text H B 2m 2m Show Transcribed Text Ac, = 30 kN 15| ΑΣΦ | 241 Submit Request Answer G vec 40 kN 2 m g Determine the vertical displacement of joint C measured downward. Express your answer in terms of A and E. Express the coefficients using three significant figures. Enter positive value if the displacement is downward and negative value if the displacement is upward. 30 kN 2 m ? 2 m m
Determine the force in members BC, GA, and BG of the truss shown in the figure below. Let P = 175 kN. NOTE: If your answer is a compressive force then just put a negative sign. If your answer is a tensile force then just type the answer directly. (ALSO, DON'T FORGET THE UNITS) 2P 2P 30 60V60° 60°V60° C 30 D 3P 4m 4m 4m Solve the force in member BC. Solve the force in member GA. Solve the force in member BG.
The cross sectional area of each member of the truss shown in the figure is A = 500 mm^2 and E = 200 Gpa. Use Catigliano's Theorem. Determine the vertical displacement of joint C if a P force is applied to the truss at C If no loads act on the truss, what would be the vertical displacement of joint C if member AB were 8 mm too short.(use data at ¶N/¶P) If P force and fabrication error are both accounted, what would be the vertical displacement of joint C
5. A certain object with a weight of 50N was found by a Structural Engineer in the area of his desired location for the truss to be erected. He recorded the angle of theta to be 65°. What are the values of the Tension AB and Tension AC. AB MN Newton
A truss is subjected to loads as shown. Assume AE is constant and use virtual work method for deflection of truss. 4m 120 KN B A TINT 3m EA = constant E = 200 G Pa 2 A = 1,500 mm Find the vertical deflection at B in mm
Consider the truss shown in (Figure 1). Assume the members are pin connected at their end points. TakeA = 130 mm2, and E= 200 GPa for each member. Use the method of virtual work to solve this problem. Determine the horizontal displacement of joint D measured leftward. 8 kN 3 m 3 m 4 m C B
Problem 1. Determine the vertical displacement of joint A. Each bar is made of steel and has the cross-sectional area shown. Take E = 29,000 ksi. Use the method of virtual work. A 10 k to 056 2 in² 3 in² 10 ft E 3 in² an@d B os /olee 2 in² 2 in² 3 in² 10 ft Figure 1 Problem 2. Solve Problem 1 using Castigliano's theorem. 6 k D 3 in² 10 ft с