Consider the circuit shown that has two resistors (each with resistance R = 8.00 Q), a battery with negligible internal resistance (V= 12.0 V), and a lightbulb. If the resistance of the lightbulb is 3.50 , calculate the power output of the lightbulb (ie. the rate at which energy is dissipated in the lightbulb). R R V 12 W 2.2 W 6.8 W 4.0 W

Consider the circuit shown that has two resistors (each with resistance R = 8.00 Q), a battery with negligible internal resistance (V= 12.0 V), and a lightbulb. If the resistance of the lightbulb is 3.50 , calculate the power output of the lightbulb (ie. the rate at which energy is dissipated in the lightbulb). R R V 12 W 2.2 W 6.8 W 4.0 W

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter9: Current And Resistance

Section: Chapter Questions

Problem 55P: A 20.00-V battery is used to supply current to a 10-k resistor. Assume the voltage drop across any...

See similar textbooks

Similar questions

(a) What is the resistance of a lightbulb that uses an average power of 75.0 W when connected to a 60.0-Hz power source having a maximum voltage of 170 V? (b) What If? What is the resistance of a 100-W lightbulb?
Figure P29.60 shows a simple RC circuit with a 2.50-F capacitor, a 3.50-M resistor, a 9.00-V emf, and a switch. What are a. the charge on the capacitor, b. the current in the resistor, c. the rate at which the capacitor is storing energy, and d. the rate at which the battery is delivering energy exactly 7.50 s alter the switch is closed?
A 20.00-V battery is used to supply current to a 10-k resistor. Assume the voltage drop across any wires used for connections is negligible, (a) What is the current through the resistor? (b) What is the power dissipated by the resistor? (c) What is the power input from the battery; assuming all the electrical power is dissipated by the resistor? (d) What happens to the energy dissipated by the resistor?
A flashing lamp in a Christmas earring is based on an RC discharge of a capacitor through its resistance. The effective duration of the flash is 0.250 s, during which it produces an average 0.500 W from an average 3.00 V. (a) What energy does it dissipate? (b) How much charge moves through the lamp? (c) Find the capacitance, (d) What is the resistance of the lamp? (Since average values are given for some quantities, the shape of the pulse profile is not needed.)
A lightbulb is connected to a variable power supply. As the potential across the bulb is varied, the resulting current and the filaments temperature are measured. The data are listed in Table P28.38. a. Find R for each entry in Table P28.38, and then plot R as a function of T. b. Assume that room temperature is at 293 K. Find R0 (resistance at room temperature). Comment on your result.
(a) What is the resistance of a light bulb that uses an average power of 75.0 W when connected to a 60.0-Hz power source having a maximum voltage of 170. V? (b) What is the resistance of a 100.-W lightbulb?
Consider the circuit shown below. If the voltage source is set to 10 V, R1 = 800 and R3 = 800. Choose R2 so that the current through that resistor is equal to 10 mA. Compute the total power dissipated by the circuit.
The internal resistance of a high voltage power supply is 4 MO and the output is set so that the potential difference across the output when on open circuit is 1800 V? A load resistor RL = 500 kn is connected across the supply. What is the current flowing in the load resistor?
Consider an electric circuit containing a capacitor, resistor, and battery; see the figure. The charge Q(t) on the capacitor satisfies the R V equation R dt O' OP V, where R is the C resistance, C is the capacitance, and V is the constant voltage supplied by the battery. a) If Q(0) = 0, find Q(t) at any time t, and sketch the graph of Q versus t. Q(t) = %3D b) Find the limiting value QL that Q(t) approaches after a long time. The limiting value Qz that Q(t) approaches after a long time is QL c) Suppose that Q(tı) = QL and that at time t = t; the battery is removed and the circuit is closed again. Find Q(t) for t > tį and sketch its graph. Q(t) =
A capacitor, resistor, and an open switch are attached in series as seen below. Initially the switch is open with the capacitor charged. The switch is then closed at time t = 0.00 s. At some time later, the current across the resistor is measured to be 4.0 mA. If the capacitance of the capacitor is 6.6 μF and the resistance of the resistor is 8.8 k, what is the charge on the capacitor in μC? di S
Given a capacitor with capacitance 10.0 ± 0.1 µF and a resistor with resistance 10.0 ± 0.2 MΩ. What is the time constant (including the uncertainty)?
the emf source E = 2,9 V, of the curcuit shown in the figure has negligible internal resistance.The resistors have resistances R1=1,2 ohm and R2=3,4 ohm. The capaccitance C = 3,1 uF. a) determine the constant r, in units of microseconds for charging the capacitor? b)what is the charge Q on the capicotor in units of microcoulomb ?