Consider the circuit shown in the figure below. The four capacitors have capacitances C₁ = 3,8µF, C₂ = 3µF,, C3 = 16µF, C₁ = 8,6µF and are connected to a battery of voltage V = 2,7Volts. When all capacitors are fully charged, determine the charge on C2. Express your answer in units of μC using two decimal places. C2 C3 CA C1 V

Consider the circuit shown in the figure below. The four capacitors have capacitances C₁ = 3,8µF, C₂ = 3µF,, C3 = 16µF, C₁ = 8,6µF and are connected to a battery of voltage V = 2,7Volts. When all capacitors are fully charged, determine the charge on C2. Express your answer in units of μC using two decimal places. C2 C3 CA C1 V

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter19: Capacitors

Section: Chapter Questions

Problem 3PA: You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors...

See similar textbooks

Similar questions

A capacitor uses air as a dielectric and has a capacitance of 3 F. A dielectric material is inserted between the plates without changing the spacing, and the capacitance becomes 15 F. What is the dielectric constant of this material?
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?
A postage stamp mica capacitor has the following color marks starting at the upper left dot: yellow, violet, brown, green, no color, and blue. What are the capacitance value, tolerance, and voltage rating of this capacitor?
4. In what form is the energy of a capacitor stored?
A pure capacitive circuit is connected to a 480-volt, 60-Hz power source. An ammeter indicates a current flow of 24 amperes. The circuit current must be reduced to 16 amperes by connecting a second capacitor in series with the first. What is the value of the existing capacitor? What value capacitor should be connected in series with the original capacitor to limit the circuit current to 16 amperes?
In a pure capacitive circuit, does the current lead or lag the voltage?
Can current flow through a capacitor?
Determine the total capacitance, total charge, individual voltage drop and charges across each capacitor. Use two decimal places for your answer. Put your answer for the individual voltage and charge for each capacitor in a table for faster checking. Thank you! Here are the values for the capacitors: C1 = 34 C6 = 29 C2 = 46 C7 = 38 C3 = 28 C8 = 23 C4 = 43 C9 = 32 C5 = 24 C10 = 23
Part B. Series-Parallel Capacitor Four capacitors are connected as shown in the figure below. Determine the following: A. Total Capacitance (CT) B. Total Charge (QT) C. Individual Charges (Q1, Q2, Q3, Q4) D. Voltage drop in each capacitor (V1, V2, V3, V4) C3 = 45 nF C2 = 5 µF C = 2.5 µF Vr = 30 V C4 = 30 nF