Consider a twin-engine jet aircraft with an elliptical wing and has the following characteristics: b = 36 ft S = 164 ft? W = 3,370 Ib CDo = 0.03 The aircraft is flying at a standard altitude of 10,000 ft with a velocity of 102 mph. If the thrust available for each engine is 1,100 lb, calculate a) Pa b) PR C) PRmin- Assume level flight condition.

Consider a twin-engine jet aircraft with an elliptical wing and has the following characteristics: b = 36 ft S = 164 ft? W = 3,370 Ib CDo = 0.03 The aircraft is flying at a standard altitude of 10,000 ft with a velocity of 102 mph. If the thrust available for each engine is 1,100 lb, calculate a) Pa b) PR C) PRmin- Assume level flight condition.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1/ A) An impulse wheel is to be designed to develop at the nozzle pressure is 40 kg/cm and the deflect the jet impinging on them 150°. The center line of the bucket is on a circle of 250 cm find:- 1. The speed of the Pelton wheel (rpm). 2. Efficiency and hours power the theoretical, at the nozzle flow rate 3 m/sec. 3. Specific speed. B) What importance has the ratio? M = (mean diameter of Pelton wheel)/ (least diameter of jet) in designing the Pelton turbine.
A turbine develops 10 MW under a head of 25 m at 135 rpm. a) What is the specific speed? b) What would be its normal speed for a head of 20 m c ) it's output under a head of 20 m?
The impeller diameter of a centrifugal pump used in water pumping is 250 mm, the inlet radius of the water to the impeller blades is 25 mm, and the outlet radius is 10 mm. The inlet angle of water to the blade is 30°, and the outlet angle from the blade is 25°. The blade inlet width is 10 mm, and the outlet width is 5 mm. Given that the pump's rotation speed is 1800 rpm; a) Find the flow rate of the water passing through the pump?b) Find the required shaft power for the pump under ideal conditions?c) Find the pump's discharge head under ideal conditions?
02. The aizelane has 50000 kg mass and 300 m² wice.elane area, Maximum lift coofficient of the wing is 3.2. Droe force coefficient ot 12000 m altitude is ebut 0.03. The speed of the aicelane at 12000 m altitude is 700 km/h. a) Calcujate the taksott sessd of the airelane. b) Çalculate the engine power at 12000 m gltitude. (Note: The density of the ait at 12000 m altitude is about Q.42 ke/m)!
A two-blade wind turbine is exposed to 60 mile/h wind. Downstream of the propeller the wind speed is 45 mile/h. The propeller has a diameter of 45 ft. Assume ideal gas and standard condition for air to find a) the thrust on the wind turbine, b) the power delivered to the wind turbine, c) the maximum power extracted by the wind turbine, d) the maximum efficiency obtained from this wind turbine.
A brand-new pick-up truck was driven and tested on a national highway. Due to a very light traffic, 8hp is highly required to drive the said vehicle with a mass of 1800kg at a speed rate of 60kph. Consider the friction and air resistance. a) How much power is needed in order to drive the truck at a same rate up a 10% grade (a hill rising 10m vertically in 100m horizontally)? (in hp)b) Meanwhile, how much power is required for the truck still at a same rate down a 1% grade? (in hp)
There is a double effect cylinder whose plunger and stem have a diameter of 80 mm and 20 mm, respectively. This cylinder is connected to a compressed air network at 2 MPa pressure. Assuming there is no friction: a) Calculate the force exerted by the stem in the forward race.) b) Calculate the force exerted by the stem in the return stroke) c) Draw the symbol of a hydraulic valve 4/3 and explain its operation.
2. A car is traveling on a highway at 28 m/s. a) What is the pressure at the bottom of a car's gas tank. that is a cube with side lengths of 0.5 meters? Assume the tank is full of gasoline with a denisty of 800 kg/m^3. b) How much pressure does a pump need to supply in order to draw gasloine from the bottom of the tank to the top of the tank? The velocity of the gasoline once it is pumped out of the tank should be 1 cm/s; the gas at the bottom of the tank is at rest. c) The gasoline from part b flows through a tube (cylinder) of radius lcm before entering a larger tube of radius 10cm. What will the velocity of the gasoline be in the larger tube? d) The tires on the car have an outer radius of 0.2 meters. How many complete rotations did the tires go through in one hour? Hint: Determine how far the car travels in one hour. e) How many hours can the car travel before running out of gas? f) During your journey. you hit a pothole and have to change your tire. You get your spare…
I need the answer as soon as possible
a) A suction pump. Consider a pipe that is inserted vertically into water. By suction, the pipe is evacuated of air. How high will the water rise? b) A water turbine is designed to extract kinetic energy from the hor- izontal flow of water and convert it into rotation of the turbine. You may assume that the height of the fluid does not change as it flows through the turbine, and that the fluid is incompressible. If the velocity is lowered from 100 m/s to 70 m/s as the fluid flows through the turbine, what is the change in pressure? c) Is the pressure higher upstream or downstream? d) The fluid in (b) is replaced by air to make a wind turbine. What is the change in pressure now for the identical change in velocity to (b)?
1) A pipe carries water from the bottom of a pool to the top of a water slide with the aid of a pump. The pool is 3 meters deep and the water slide is 5 meters above the surface of the pool. The pipe carrying the water has uniform area. A diagram of the system is shown here. Open to atmosphere Pump Pool a) If the pump's output is 62 kJ/m³ and the flow rate is 0.3 m³/s, what is the resistance in the pipe? b) The pool is partially drained for construction. How low can the water go in the pool before the water in the pipe stops flowing? c) After long use, sediment builds up in the pipe, increasing the resistance and decreasing the area of the pipe uniformly. How do these changes affect the current in the pipe?
Maximizing the wind velocīty of 92 m/s and 25 units of wind turbine was installed at the seaside shore What is the total power if the area of turbine blade equal to 42 sq.m with air density of 1.2041 Kg/cu.m. 1.969 MW 1.968,998 Watts c) 4,923 watts 49.23 MW